HOLY STONE HS430 Drone with Camera for Kids Instruction Manual

Instructions For Use

HS430 Drone with Camera for Kids

V3.0
HS430

+1(855) 888-6699
www.holystone.com
  usa@holystone.com (USA)
eu@holystone.com [EU)
Ca@holystone.com (CA)
jp@holystone.com (JP)

DISCLAIMER & WARNING

1. Please read this Disclaimer & Warning and Safety Guidelines careful before using our product. This product is not recommended for people under the age of 14. By using this product, you hereby agree 1o this disclaimer and signify that you have read it fully. You agree that you are responsible for your own conduct and any damage caused while Using this product, and any consequence. You agree to only use this product for its designed purposes and in accordance with the local laws, reguiations and all applicable policies and guidelines that HolyStone may provide.
2.  When using this product, please be sure to strictly abide by the speciication requirements and safety guidelines statedin- this document. Any personal injury. property damage. legal disputes and al other adverse events caused by the violation of any of the safety instructions or due to any other factor, WILL NOT be HolyStone’s responsibiliy.

SAFETY GUIDELINES

2.1 Check Before Use

1. This product is a high precision drone that integrates various electronic stability and control mechanisms. Please be sure to configure this drone carefully and correctly to ensure safe, accidentfree operation,
2. Ensure that the batieries of the drone and transmitter are clean, undamaged and fully charged before every use.
3. Ensure that al the propellers are undamaged and are installed in the correct orientation
4. Pease perform a orough check of the product before each use. Inspect the integrity of the parts, any signs of cracks and wear off on the propeliers, battery power and effectiveness of the indicator, etc. If there is any problem found after checking the drone, please refrain from using it until the problem is resolved

2.2 Flight Environment

Avoid fiying over, or near obstacles, crowds, high voltage power lines, trees, airports or bodies of water.
DO NOT fly near strong electromagnetic sources such as power fines and base stations as it may affect the onboard compass,DO NOT use this drone in adverse weather conditions such as rain, snow, fog, and wind
2.3 Operation Requirements

1. DO NOT use this product to follow any moving vehicles.
2. During the flight, turn off the motors only in case of an emergency.
3. When the battery runs low, return the drone back to your starting point
4. DO NOT use this product if you feel tired, take medicine or feel unwel and drink alcohol.
5. Be aware of the volume of noise that the drone produces. Please. ensure to keep your distance to avoid ear damage.
6. Stay away from the rotating ‘propellers and motars.
7. DO NOT fly in any spaces  where drones are prohibited. Please respect people’s right to privacy by not flying your drone close to others.

2.4 Use of Battery

1. Please ensure batteries are fitted in the correct orientation as shown in the instruction manual
2. Avoid short circuits by ftting the batteries correctly, and do not crush to squeeze the batteries as this could cause the fisk of fire or explosion.
3. DO NOT mix new and old batteries as this can lead o poor performance of the product.
4. Please cispose of used batteries carefuly, do not iter and recycle where ever possible.
5.  DO NOT expose dead batteries to heat or fire or they may explode
6. If the device is not going to be used for an extended period of time, please remove batteries t0 prevent potential damage to the drone from battery leakage
7. Only use the USB charging cable that comes with the drone to charge the battery.
8. DO NOT connect the battery directly to wall outlets or car cigarette Jighter sockets as this will damage your battery since they have different votages
9. DO NOT attempt to disassemble or modify the battery in any way
10. DO NOT use the battery if it gives off an odor, generates heat, becomes discolored, deformed or appears abnormal in any way. I any of these situations occur while the battery is in use or being charged, remove it from the device or charger immediately and discontine use.
11. DO NOT pierce the battery casing with a nail or any other sharp object, break it open with a hammer, or step on itl Dispose or recycle this battery as it may cause personal injury or damage to your drone.
12. Always charge the batteries on a fireproof surface and away from combustible materials. DO NOT charge on surfaces that can catch fire, which includes: wood, cloth, carpet.
13. DO NOT immerse the battery in water or get it wet.
14. DO NOT solder battery termina in any way.
15. Keep batteries out of reach of children or pets.
16. DO NOT short-circuit the battery by connecting wires or any other metal object to the positive+] and negativel-) terminals

Li-Po Battery Disposal & Recycling
Wtioyssotb placed iooe conoctocal nvormenia o waste agency to the waste agency orthesuppier to your model to yout nerest 49 bty eceling cencer. ****

MAINTENANCE

1.  Clean the drone after each use with a clean, soft cloth.
2. Avoid prolonged exposure to direct sunlight and avoid buildup of heat on the drone or batteries.
3. This device is not waterproof and must not be submerged or subjected to water nder any circumstance. Failre (o keep the device completely dry will resultn Tailure and permanent damage to the unit Be aware that although it might be dry where you are, droplets of rain or mist from a river or waterfall could damage your drone where it is flying.
4. Frequently check the charging plug and other accessories for signs of damage. If any part of the device or cables are damaged, avoid use or charging until the damaged parts are replaced

 PACKAGE CONTENTS

| |
---|---|---
Drone| Transmitter| Drone Battery
| |
USB Charging Cable| Spare Propellers| Screwdriver
| |
Propeller Guard| Instructions For Use

DRONE DETAILS

TRANSMITTER DETAILS

Open the battery cover on the back of the transmitter, insert the three AAA batteries (ot included) into the battery compartment, and close the battery cover to complete the installation.
**** When installing the batteries, please pay attention to the  positive and negative polarity of the batery to ensure the correctinstallation of the batteries.

JOYSTICK MODE

7.1 MODE 2 (Default Setting)

7.2 MODE 1
To enter Mode 1, long press the Trimmer button while turning on  the transmitter. (Please do not release the Trimmer button until thetransmitter is powered on.)

INSTALLATION

8.1 Drone Battery
Installation:

Push the battery sure that you hear a click sound indicating the battery is firmly instay correctly into the drone battery compartment.
Attention: The battery should be installed firmly, failure to do so may affect the flight safety of your drone. The drone may crash due to a power-cut during the flight.
Removal:

As shown in the above, press the lock button on the battery and pul it back to remove the battery from the fuselage
8.2 Propellers

Connect each propeller to its corresponding motor shaft, either position “A/B”, then lock the propeller to the motor shaft with a screw.
Attention: Pay attention to the “A” or “B” printed on each propeller. The drone will not fly unless the correct propeller is installed on the correct motor shaft.

8.3 Propeller Guard

As shown in the picture, install the propeller guard to the motor base.
8.4 Phone Holder

As shown abave, open the phone holder completely [Pic.1]. Adjust the  phone holder upward and downward according ing to the size of phone (Pic.2)

CHARGING

1. When the drone battery runs low, the indicator lights on the drone wil biink continuously
2. Connect the battery with the USB charging cable.
3. Plug the USB charging cable into a USB charging port on the power bank or USB adapter (5V/14]
4. When the batiery is charging, the indicator light on the USB charging cable s red. When the battery is charged, the indicator light on the USB charging cable tums green
5. The charging time is about 100 minutes
   **** Before charging, please read the introduction of the “Use of Battery” section of the “Safety Guidelines” carefully!

OPERATION GUIDE

10.1 Download APP

https://apps.apple.com/us/app/holystone-fpv/id1557382812https://play.google.com/store/apps/details?id=com.mjx.holystone

Scan the OR code, connect to the App Store™ or Google™ Play and download the “HolyStone-FPV” application for free.
Required Operating Systems: iOS 9.0 or later/Android 5.0 or later.
10.2 Connect to Wi-Fi
Connect your phone to the Wi-Fi network created by the drone. You can check the drone’s status on the HolyStone-FPV App.

1. Make sure to turn off Bluetooth, Mobile Data, and VPN. Enter your phone’s Wi-Fi settings and click Wi-Fi to search for the Wi-Fi of the drone. {Make sure to turn on the drone before going to the W/Fi settings on your phone}
2. Select the Wi-Fi network: HolyStoneFPV-* *****,
3. Wait for a couple of seconds for your phone to connect to the drone’s Wi-Fi.
4. Enter the HolyStone-FPV application. > The connection between your phone and the drone is established automatically.

Attention: The Wi-Fi network created by the drone does not access the Internet.
10.3 Pairing
Al of the following operations on this manual uses MODE 2.

1. Long press the Power Switch to tum on the drone, the indicator lights of the drone will keep fashing.
2. Place the drone on a flat and level surface with the head forward and the tail facing towards the pilot.
3. Long press the Power Switch to turn on the transmitter, and you will hear the “DiDi” sound, then the indicator lights keep flashing.
4. Push the throttle joystick up then down to pair the drone with the transmitter. The indicator lights on the drone will turn solid if the drone is paired successfully.

10.4 Calibrating the Gyro

Simultaneously push the left joystick and the right joy right comer to calbrate the gyro. The indicator ights on the drore will blink and turn solid, and the transmitter will send out a long “Di* sound, which indicates the calibration is completed
Tip: To ensure a stable flight, we suggest that the pilot calibrates the gyro every time after pairing the drone and after a crash.
10.5 Unlocking/Locking the Motors

Unlocking the Motors: As shown above, push the left oystick to the bottom right comer and the right stick to the bottom left corner at the same time to uniock the motors. The motors wil start to spin.
Locking the Motors: Repeat this operation, the motors will siop immediately.
10.6 Auto Takeoff
There are two methods to take off the drone.
Method 1:

Alter paifing/calibration, unlock the motors, short press the One Key Takeoff/Landing button, the drone will take off automatically and hover at 4 feet altitude.
Method 2:

After pairing, pick up the drone and lay it flat on your palm. Gently toss the drone into the air, and it will hover in place.
10.7 One Key Landing

During the flight, snorty the drone will land on the ground automatically.

FUNCTIONS DETAILS

11.1 Emergency Stop
**** The Emergency Stop function should only be used in case of emergency during the flight to avoid any damage or injury.

As shown above, long press the One Key Takeoff/Landing button for 2 seconds, the motors will stop immediately.
Attention: Be aware that you risk breakage of the drone if it falls a large distance or hits anything at a high rate of speed.
11.2 Trimmer

F/B Sideways Drift Trim: If the drone tends to drift forward, hold down the Trimmer button and do not release it while pushing the direction joystick down to re-balance the drone. If the drone tends to drift backward, hold down the Trimmer button and do not release it while pushing the direction joystick up to re-balance the drone, L/R Sideways Drift Trim: If the drone tends to drift left, hold down the Trimmer button and do not release it while pushing the direction joystick right to re-balance the drone. if the drone tends to drift right. hold down the Trimmer button and do not release it while pushing the direction joystick left to re-balance the drone.
11.3 Speed Switch

This drone comes with 2 speed modes (Low/High]. As shown above, push the Speed Switch button to the left, the transmitter sends out a Di” sound, indicating Low Speed. Push the Speed Switch bution to the fight, the transmitter sends oLt a “DIDI” sound, indicating High Speed.
11.4 Take Photo/Record Video

Take Photo: Short press the Take Photo/Record Video buition, the transmitter sends out a “Di” sound, indicating that the camera has taken orie photo successfully
Record Video: Long press the transmitter sends Take Photo/Record Video button, the  out  a “DIDI” sound, indicating that the mera is recording video. Long press the button again to exit the Record Video
11.5 High-Speed Rotation

During the flight, short press the High-Speed Rotation button, the transmitter will make a “Di” sound, which indicates that the drone enters the High-Speed Rotation function. The drone will exit the High-Speed Rotation function automatically 10 seconds after, and you can also push the direction joystick to any direction to stop the rotation.
11.6 Circle Fly During the flight, long press the Circle Fly button, the transmitter will make a long “Di” sound, which indicates that the drone enters the Circle Fly. This drone will exit the Circle Fly function automatically 10 seconds after, and you can also push the direction joystick to any direction to exit the Circle Fly.
11.7 360° Flip

When you get familir with al the functions of the drone, you can try this amazing fip mode the Right Joystick on the transmitter, then push the right joystickfe. When youfly the drone at feast 10 feet, press in Forward/Backward or Lefi/Right, and the drone will do a fip towards the corresponding direction
Tip: This function will perform better when the battery is fully charged.
If you do not operate after entering the 360″ Fiip, short press the right joystick again to exit the 360″ Fiip
11.8 Altitude-hold Function

The drone is designed with an altitude-hold function so the drone can maintain its alitude The left joystick. (The left joystick you relea will automatically spring back to the midde)
11.9 Headless Mode
****Please familiarize yourself with the Headless Mode function first before using this mode. Otherwise, it is easy to lose the drone and cause unnecessary loss.

1. After pairing/calibration, short press the Headiess Mode button on the transmitter. In Headless Mode, the indicator lights of the drone will flash continuously, and the transmitter sends out beeps continuously.
2. Press the Headless Mode button again, and you will hear a beep from the transmitter, indicating the drone exits the Headless Mode.

While in Headless Mode, pushing the directin joy stick forward will make it iy in the direction th e drone faces when it he head to takes off. To make sure the pilot can tell drone’s direction, during the flight, we recommend that 1 pilot stays facing the same direction that the drone head faces at take-off. By doing so it is nsured that when the pilot pushes the direction joystick forward/backward, the drone wilfly forward/backward toward him/her. If the pilot moves the direction Joystick efy/right, the drone will move left/righi relative to hirmyher

SPECIFICATIONS

• DRONE
  Model H5430
  Weight: 75/2 6502
  Max Flight Time: 13 minutes [per battery)
  Motor Mode: 716
  Operating Temperature Range: 32″ to 104°F (0″ 0 40°C) Size: 187+13543mm{Unfolded) 9363*43mmiFolded)

• DRONE BATTERY
  Capacity: 730mAh
  Voltage: 385V
  Battery Type: Lithium-ion Polymer Battery
  Energy: 281Wh
  Charging Temperature Range: 41° 1o 104°F (5″ t0 40°C)
  Charging Time: 100minutes (Depends on charging power and remaining battery power|

• TRANSMITTER
  Operating Frequency: 2452-2474MHz
  Max Flight Distance: 13 feet/40m (Otdoors and unobstrLicted)
  Operating Temperature Range: 32″ to 104F (0″ t0 40°C)
  Battery Type: 3*1.5V AAA Battery (Not included]

• CAMERA
  Operating Frequency: 2417MHz
  Lens Angle: 67
  Manual Adjustable Range: -90’~0″
  Photo Resalution: HD1920 x 1080P
  Video Resolution: HD1920 x 1080P
  Max Transmission Distance: 98feet/30m [Outdoors and unabsiruct ed)
  Live View Quality: 20ps
  Photo Formats: JPEG
  Video Formats: MP4/AVI
  Operating Temperature Range: 32″ 0 104°F (0 to 40°C)

• USB CHARGING CABLE
  Input 5v/1A
  Rated Power; s5W

CONTACT US

Please do not hesitate to contact us if you need further support.
  4:00 PM ~ 7:00 AM (PST)
 usa@holystone.com (America)
ca@holystone.com (Canadal
eu@holystone.com (Europe] **** +1(855) 8886699

https://webchat.7moor.com/wapchat.html?accessId=033f17e0-68e8-11eb-b704-1d14beee0e86&fromUrl

For online support, please scan this code with Live Chat

GENERAL INFORMATION

FCC Notice:
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference that may cause undesired operation.
The Supplier’s Deciaration of Conformity is available at the following address https://wwwv.holystone.comy/Download/US/HS430_FCC_sDoCpdf
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference o radio communications. However, there s no quarantee that interference will Not occur in a particular instaliation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/ TV technician for help

WARNING: Changes or modifications rot expressly approved by the party responsible for compliance could void the users authorty to operate the equipment
RF Exposure
The equipment complies with FCC radiation exposure imits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body.
IC Norice:
This device complies with Canada Industry licence-exempt RSS standard (s). Operation s subject to the following two conditions:
(1] ths device may rot cause interference; and
(2} this device must accept any interference. Including interference that may cause undesired operation of the device.
CAN NMB-003 (8] RF Exposure
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for  an uncontrolled environment. This equipment shouid be installed andoperated with minimum distance 20cm between the radiator & your body.
HOW TO RECYCLE THIS PRODUCT
This symbol on the product or its documentation indicates that it MUST not be disposed of together with household waste.
Uncontrolled waste disposal may harm the environment or human health
Please separate your device from other types of waste of recycling it responsibly.
This will help to foster the sustainable re-use of material resources.
We suggest you contact your retailer, inquire at your local town hall or business store to find oLt where and how the drone can be recycled
BATTERY WARNING:

1. Failure to follow all the instructions may result in serious injury. ireparable damage to the battery may cause a fire, smoke or explosion a5 well
2. Always check the battery’s condition before charging or Lsing it
3. Please replace the battery if the battery is dropped or has any peciliar smell, overheating, discoloration, deformation or leakage happens.
4. Never use anything other than the approved LiPo Charger to charge the battery. Always use a balancing charger for LiPo cels or a LiPo cel balancer. It is recommended that you Use the one provided with the product
5. The battery temperature must never exceed 60°C[140°F) otherwise the battery could be damaged or ignited.
6. Never charge the battery on a flammable surface, near flammable products or inside a vehicle(lt is better to place the battery on a non-flammable and non-conductive suiface).
7. Never leave the battery unattended during the charging process Never diszssemble or modify the housing’s wiring, or puncture the cells. Always ensure that the charger output voltage corresponds to the voltage of the battery. Do not short circut the batteries.
8. Never expose the Li-Pa battery to moisture or direct sunfigh, or store: it in a place where lemperatures coLid exceed 60°Cicar in the sun, for example].
9. Aways keep it oLt of reach of chidren 10 Improper battery use may resLit in a fire, explosion or other hazards.
10. Nonechargeable batteries are not allowed to be recharged Rechargeable batteries should be charged under adults’ supervision.
11. DO NOT mix different types of batteries including the new and Used ones.
12. Batteries MUST be inserted with the correct polarity.
13. The supply terminals MUST not to be shortcircuited. Reguiar examination of transformer or battery charger for any damage to their cords, plugs, enclosures and other parts MUST be done. If there is damage, they MUST ot be used until the darmage has been repaired.
14. The packaging has to be kept since it contains important information.
15. The toy is shouid only be connected to the equipment with symbol Class II
    EU RF Power(EIRP): <10 dBm (2452MHz ~ 2474 MHz)

Caution

1. The max aperating of the EUT is 45°C. and shouldn’t be lower than -10°C
2. The device complies with RF specifications when the device used at 0mm from your body.
3. Declaration of Conformity.

We, Xiamen Huoshiquan Import & Export CO,LTD hereby, declare that the compliance of the essential requirements with the Directive 2014/53/EU, the RoHS Directive 201 1/65/EU and Safety Directive 2009/48/EC have been fully fulfilled on our product with indication below:
Product Name: Remote control four axis series
Model/Mark: Hs430/HOLYSTONE
The Statement of compliance is available at the following address http://www.holystone.com/Download/CE/HS430_EU_DOCpdf
This product can be used among EU member states
MANUFACTURER INFORMATION
Manufactured by
Xiamen Huoshiquan Import & Export CO.LTD,
Address: Unit 1,
Room 501, Hongxiang Building, No 258 Hubin Nan
Road, Siming District, Xiamen, China
+11855) 888-6699

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>