linptech K9B Series Self Powered BLE Wireless Switch User Manual
- June 14, 2024
- linptech
Table of Contents
linptech K9B Series Self Powered BLE Wireless Switch
Product Introduction
K9B Series Self-powered BLE Wireless Switch
Linptech K9B series self-powered BLE wireless switch, which is a BLE broadcast transmitter with no wiring and batteries, and can be used with the corresponding receiver/wall switch/gateway to achieve lighting control, interaction and other functions, please refer to the instruction manual to learn the specific use methods and pairing operation. The K9B series self- powered BLE wireless switch uses innovative self-powered technology to collect the energy at the moment of switch action for sending wireless sign- als without batteries, eliminating the trouble of battery replacement and protecting the environment.
Installation Instruction
Option 1:
Tear off the double-sided tape and stick it on the wall if the wall is clean
- Tear off one side of the double-sided tape and stick it onto the back of the switch, and then remove the protective film of the dou- double-sided tape.
- Stick the switch onto the wall and press firmly.
Option 2:
Install the switch in the position of the original switch by using screws
.
- Pull up to remove the back cover.
- Install the back cover onto the 86mm switch case with screws.
- Push the switch onto the back cover.
Product Parameter
Environmental protection
The device and its accessories (if included) should not be disposed of with household garbage. Disposal of the device and its accessories is subject to local regulations. Support proper collection and recycling.
Disposal and recycling information
- This symbol (with or without a solid bar) on the device, and /or the packaging, indicates that the device and its electrical accessories (for example, a cable) should not be disposed of as household garbage. These items should not be disposed of as unsorted municipal waste and should be taken to a certified collection point for recycling or proper disposal. For more detailed information about the device, contact your local city office, household waste disposal service, or retail store. Disposal of the device is subject to
- WEEE Directive Recast (Directive 2012/19/EU) . The purpose of separating WEEE from other waste is to minimize the potential environmental impacts and human health risks of any hazardous substances that may be present.
- Reduction of hazardous substances This device is compliant with the REACH Regulation [Regulation (EC) No 1907/2006] and RoHS Directive Recast (Directive 2011/65/EU).
EU Regulatory Conformance Statement
Hereby, Wuhan Linptech Co., Ltd. declares that this device is in compliance with the essential requirements and other relevant provisions of 2014/53/EU.
The following marking is included in the product:
This device may be operated in all member states of the EU. Observe national and local regulations where the device is used. This device may be restricted for use, depending on the local network. Restrictions in the 2.4 GHz band: Norway: This subsection does not apply for the geographical area within a radius of 20 km from the center of Ny-Alesund.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note : The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to op- erate the equipment. The device has been evaluated to meet ge- neral RF exposure requirement. To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s)
Self-powered BLE Wireless Switch User Manual V1.1 Model: K9B-W1,K9B-W2,K9B-W3
Please read this user manual carefully before using the product and keep it
properly.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>