INALSA Micro WD12 Wet And Dry Vacum Cleaner Instruction Manual

INALSA Micro WD12 Wet And Dry Vacum Cleaner

Dear Customer,
Congratulations! On the purchase of your INALSA Wet & Dry Vacuum Cleaner! this is designed to include many superior features that permit you the fullest expression of your cleaning skill and enthusiasm. You are now on the threshold of a whole new world of cleaning pleasure. At INALSA, we have a reputation of manufacturing innovative, high quality appliances such as Food Processors, Mixer Grinders, Cooking Ranges, Air Fryers, Oven Toaster Grillers, Hand Blenders, Electric Kettles, Electric Chimneys, Garment Steamers, Vacuum Cleaners & Power Tools. Your newly acquired INALSA Wet & Dry Vacuum Cleaner bears the same distinctive hallmark of excellence. It is all the result of vigorous quality consciousness in INALSA’s design and development where uncompromising standards are maintained and rigid quality control measures are exercised on raw materials, components and finally, the finished product. Your INALSA Wet & Dry Vacuum Cleaner has a lot of thoughtful features built in to make your living convenient. Please read these instructions carefully, so that you may get the best out of the power packed features in your INALSA Wet & Dry Vacuum Cleaner.
Welcome to the INALSA world of living pleasure!!

Parts Identification

Part No. Part Name

1. Carry Handle
2. ON/OFF Switch (0-OFF, 1-ON)
3. Motor Unit
4. Side Locks
5. SSTank
6. Wheel Base
7. 360° Rotation Wheels
8. Power Cord
9. Suction Port
10. Wet&DrySqueezingBrush
11. 2-in-1 Crevice Nozzle
12. Small Round Brush
13. Filter Holder Ring
14. ClothFilter(Dry Use)-2 Nos (lN Fitted inside Unit& lNExtra)
15. Sponge Filter (Wet Use)
16. Extension Pipes (3Nos)
17. Flexible Hose Pipe
18. Lock Catch (Air Flow Controller)
19. Hose Handle

Technical Specification

6L (Wet use with hose pipe only)
4.SL (Wet use with other brushes)
Vacuum Pressure (max)| 14 kpa
Wind Volume of Flow| 25L/s
Noise Level| 75dB
Safety| Auto Shut Float Valve & Overheat Safety Protection

• Due to continuous improvements in product, specifications are subject to change without prior notice.

Attention
If any part is missing or damaged, please do not assemble unit until you have all the parts.

• Invert SS Tank to install wheel. Insert the four wheels into the socket of wheel base. Be sure that wheels spin freely.
• Carry handle is detachable. Connect the handle on top of the motor unit by tightening through 2 screws. (Fig 1)
• For dry use : Put the cloth bag filter into float holder and place filter holder ring upto the end of the holder to tight its assembly.
• For wet use: Put the sponge filter into float holder firmly to the end of the holder.

Important Information

1. Please read operating instructions before using the appliance.
2. The input supply from the mains must comply with the rated input.

Do’s

1. Only use the accessories that have been supplied with the vacuum cleaner, by INALSA.
2. Before starting vacuuming, any pointed, sharp-edged or very large items should be removed in order to avoid damage of filter & motor.
3. Always ensure that the surface you are vacuuming is dry (while using Dry cloth filter), otherwise you can end up damaging the vacuum cleaner. If the carpet has been recently shampooed, ensure that it has completely dried out.
4. Always remove the plug from the socket after you have finished using the vacuum cleaner, before you replace the dust bag and filter, and before you clean it.
5. The appliance is intended for household use only.
6. In the event of any malfunctions or damage, remove the plug from the socket immediately.
7. If you have an extension cable, it must be suitable for use with corresponding power rating.
8. In case of any defect, contact the nearest INALSAauthorized service centre.

Don’ts

1. Do not use near the direct flames or acid.
2. Do not use the vacuum cleaner to vacuum any type of fluid.
3. Never allow this appliance to be operated by children, or other people who are unaware of the dangers of working with electrical apparatus.
4. Never touch the plug if your hands are wet or damp.
5. Do not insert any objects into the interior of the cleaner’s housing.
6. Never use the vacuum cleaner without a filter inserted.
7. Do not wind the cable around the vacuum cleaner.
8. Do not place the vacuum cleaner near appliances such as cookers, radiators, heaters etc.
9. Do not use the cleaner to vacuum hot or incandescent items.
10. Do not immerse in water.
11. Do not try to clean the product when it is in running condition.

Attention: Before Use the products

1. Please do not use the vacuum cleaner near some liquids or gases which is inflammable and explosive in order to avoid the fire.
2. Before plug in and out, please turn off the power in order to avoid the fire and get an electric shock.
3. Please do not touch the plug when your hands are wet, in order to avoid getting an electric shock.

Warning

1. Please do not plug up the vent in order to avoid damaging the machine because the temperature inside is too high.
2. Do not suck the following objects: None extinguished cigarette, gas, kerosene, and other objects which is inflammable explosive and volatile. Do not pick up sharp object.
3. The toner lime powder gypsum and other subtle thing which easy to suck on the filter bag, it will blocking airiness, damage the motor.
4. During the using process there is some possibility that the tube and the machine generate electricity, so please pay attention.
5. Please do not overset the cleaner, in order to avoid the water in and damage the machine.
6. When water coming out of the air outlet, mending or checking up the cleaner, please do not overset it, in order to avoid the water in, and damage the motor. Do not use this product as water pump, in order to avoid damaging the machine.
7. Every time, after finish dusting, maintaining and checking-up, please turn off the power and plug out.
8. Please do not put the cleaner under the sun or other high­ temperature places, in order to avoid the plastic deforming.
9. The tube should not bend excessively, stretch force, or it will damage the tube.
10. Do not immerse the motor unit in the water or rinse the container with water, in order to avoid water flow into the electrical components, and causing the personal accident. You should use soft cloth and twisting very dry of water, then wipe the surface lightly.

How to Use

Dry Cleaning
Use the cloth bag while using vacuum cleaner for dry cleaning purpose only.

• Open the side locks, take out the motor unit, then cover the cloth bag on the bottom basket, then fix with a filter holder ring.
• After that put the motor unit into the SS tank & close the 2 side locks, now the machine is ready to clean.
• When finish cleaning or too much garbage is sucked into the SS tank, the suction force drops obviously. Please cut off the power and clean up the garbage in the barrel timely.
  1. Open the side locks, take out the motor unit.
  2. Clean up the garbage in the barrel, then put motorunit and locked it.
     (The cloth bag is consumable, please clean or replace timely)

Wet Cleaning
Use the sponge filter when using the vacuum cleaner for sucking water.

• Open the side locks, take out the motor unit, take off the dust bag and put sponge filter on the bottom basket.
• When finish cleaning or the SS tank is full of water with permitable limits (that time safety valve works) please switch the power off and pull out the water in the bucket.
  1. Open the side locks, take out the motor unit.
  2. Pull out water, then put the motor unit and locked it.
  3. Please dry the sponge filter after finish vacuum water.

NOTE: Never use wet or damp cloth filter for dry vacuum process. In that case always dries the cloth filter in sun light and use it in accordance.

The Hose Pipe & the Vacuum Cleaner Linking up 

Insert: Insert the hose pipe connector into the vacuum cleaner, and then rotate it clockwise until it locked.
Exsert: Hold the hose pipe connector, rotate it counter-clockwise until exsert the hose pipe.
When using the blowing function, insert the hose pipe into the blowing port, then rotate it clockwise until it locked. When exserting it, rotate it counter-clockwise, exsert the hose pipe.

Connecting Hose Pipe with Other Attachments

1. Contact Joint: Insert the bush at one end of the plastic pipe & push it inside until it is tight. And insert the other end of the plastic pipe into the hose pipe.
2. Exsert: Pull out outside each accessories from flexible hose pipe end & from plastic pipe until it’s out.

Function Instruction

1. Poweron
   • Insert the plug into the socket.
   • Turn on the switch.
2. Air register
   •  Adjust the suction-assisted using lock catch(18), when the lock catch open, the suction gradually decreases, when it closed, the suction is gradually increasing.

According to Diffrent Occasions. You Could Choose a Suitable Accessory

1. Small round brush is suitable for the floor, carpet and so on.
2. 2-in-1 crevice nozzle brush is suitable for the crevice comer and other places’ dusting and sopping up.
3. Wet & dry squeezing brush can be used as MOP’s and cleans dry dust, wet spillage and even dries your floor.
4. Blowing Port is suitable for blowing out the dust in the crevice comers & blown the leaves in the open area/ gardens.

Protection Device

Special instructions concerning protective device

1. When the water in the SS tank is full. The device will be keep on working but the suction power will vanish at this moment. The machine will make a noise which indicates the motor is running at a high speed. Under this circumstance, you should cut off the electricity, clean out the water. Then equip the machine and tum it on, it will begin to work normally.
2. Only connect to a proper 220-240V,AC, 50Hz socket.
3. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent to a similarly qualified person in order to avoid a hazard.
4. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction or instruction concerning use of the appliance by a person responsible for their safety.
5. Children should be supervised to ensure that they do not play with the appliance.
6. The plug must be removed from the socket before cleaning or maintaining the appliance.

Safeguard About the Float Valve

1. When water is full of the SS tank with permitable limits, the float valve starts, at this time, the sucking is pause, but it will make some unusual sounds, it means the machine is operating at a high-speed, when this situation happens, please quickly tum off the power supply, pour out of water, and then install the machine, tum on the power again , the vacuum cleaner still can operate normally.
2. When vacuum cleaner is overset, the float valve starts, please quickly tum off the power supply, set upright the vacuum cleaner , and then tum on the power again.
3. When the float valve starts, using vacuum cleaner can cause damage to the motor & can lead to a fire. In that case , we should stop using it , and pour out of water , then use it again.

Blowing Function
After absorbing sewage & other garbage, the ground is wet & needs to be dry. You can connect the hose pipe to outlet behind the motor unit. Tum ON the switch & then vacuum cleaner can be used an air dyer.
NOTE: For blowing function, do not use any filter inside the product

Trouble Shooting

instructions mentioned in Safety Feature.
The appliance has weak suction power| SS tank is full| Empty SS tank.
Unit clogged| Turn unit off and unplug from wall socket. Remove dust filter duct and check for big objects in container and remove.
Dust filter needs cleaning| Clean or replace dust filter.
The dust escapes from the appliance| SS tank is full| Empty SS tank.
Cloth filter is not installed correctly| Install cloth filter as per instructions.
Puncture/Hole in Cloth filter| Replace Cloth filter.
**** The hose or brushes do not pick up dust| Hose clogged| Remove hose and/or brushes clear obstruction from hose.
SS tank is full| Empty and clean SS tank.
Heat produced during use| A small amount of heat is normally produced by the vacuum cleaner due to high motor RPM.

Safety Feature:
This vacuum cleaner is provided with ‘Overload Protection’. In case the motor gets overheated, this protector will automatically stop the motor till the temperature is normal. In such situation, switch off the unit and restart after 20-30minutes.
For better performance, use this vacuum cleaner for 15min and then give 3 minutes break so that the motor does not heat up.
Warning: Vacuum and blower operation must be used one at a time and not together.

WARRANTY

The “lnalsa Wet & Dry Vacnum Cleaner” is fully warranted against any manufacturing defect for a period of One Year from the date of purchase. Should any defect develop iu the Wet & Dry Vacuum Cleaner during the warranty period, TUAREG MARKETING PVT. LTD. undertakes to get the Wet & Dry Vacuum Cleaner or any part thereof, repaired at any of its Authorized Service Center.

The above warranty shall be subject to the following terms and conditions:-

1. Any defective product or part thereof will be repaired within the above stated warranty period on receiptofthe samewith this card duly filled in and stamped by dealer from whom the product was purchased along with the purchase bill/ invoice, provided the product is brought to our nearest service center freight paid and packed securely.
2. In the event of repairs/ replacement of any part of product, this warranty will thereafter continue and remain in force only for the unexpired period of warranty.
3. This warranty is valid only when:-
   • The product is purchased from the company’s authorized dealer and accompanied by this warranty card / cash memo.
   • The product has been installed, used and maintained in accordance with the instruction manual.
4. The warranty does not apply to :-
   • Normal wear and tear of the product
   • The product has not been serviced by the Inalsa authorized service personnel.
   • Damage due to chipping, peeling, plating and denting.
   • Damages arising due to running of the appliances on the alternate sources of power such as Inverter, generator or any such auxiliary power supply aid resulting in variation/ fluctuating voltage
   • Breakage or damage to components made of ABS, SAN, Bakelite, Glass and such plastic/rubber parts, cord, bulbs and surface coating.
   • Damages resulting from accidents, mishandling or negligence on the part of the customer
   • Product ifused for the commercial purposes.
   • Product, the serial number of which has been removed obliterated or altered on the specification plate.
5. The warranty is in lieu of all other warranty, expressed or implied and does not cover indirect or consequential damages/ loss.

WARRANTY CARD

Dealer’s stamp and Signature

Scan and Download INALSA Connect App to Register your Warranty
E-mail: customercare@inalsa.co.in
Customer Care Number (Open on all 7 Days* from 9:30 to 18:30)
9773982065
INALSA
TUAREG MARKETING PVT. LTD.
Khasra No – 1189, Bhalswa, Delhi- 110033

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>