ZEROWATER 20 Cup Ready Pour 5 Stage Water Filter Dispenser User Guide
- June 14, 2024
- ZeroWater
Table of Contents
ZEROWATER 20 Cup Ready Pour 5 Stage Water Filter Dispenser
ASSEMBLE YOUR ZERO WATER PITCHER QUICKLY AND EASILY
ZeroWater® PITCHER MODELS: 6, 7, 8 round, 10, 10 round, 10RP, 12, 12RR.
STEP 1
Remove the TDS meter from the packaging and test your tap water. Compare to
the TDS chart on page 3 to help give a gauge of filter life.
For Ready-Read products detach the integrated meter from the device
STEP 2
Remove the lid and reservoir from the device. Unwrap the filter and
remove the branded film or blue cap (where applicable).
STEP 3
Clean your device in warm water using a mild soap then rinse and dry
thoroughly. Then rinse the exterior of your filter with warm water for 30
seconds.
Reminder please rewash your device with each filter change.
STEP 4
Twist the filter into the bottom of the reservoir. Do not drop the filter in
from above. Tighten until there is a complete seal between the filter, blue
O-ring and reservoir.
STEP 5
Fill the reservoir with cold tap water (directly onto the filter) and place
the lid on top. Allow all the water to pass through the filter before filling
again.
STEP 6
Fill your cup and enjoy.
STEP 7
Once your TDS meter reads 006 that means it is time to change your filter.
For Ready-Read products simply turn on your meter (while it is docked within
the spigot) during dispensing and get your instant read, every time.
ZeroWater® DISPENSER MODELS: 20, 22RR, 30, 32RR, 40, 52RR.
STEP 1
Remove the TDS meter from the packaging and test your tap water. Compare to
the TDS chart on page 3 to help give a gauge of filter life.
For Ready-Read products detach the integrated meter from the device.
STEP 2
Remove the lid and reservoir from the device. Unwrap the filter and remove the
branded film or blue cap (where applicable).
STEP 3
Clean your device in warm water using a mild soap then rise and dry
thoroughly. Then rinse the exterior of your filter with warm water for 30
seconds.
Reminder please rewash your device with each filter change.
STEP 4
Twist the filter into the bottom of the reservoir. Do not drop the filter in
from above. Tighten until there is a complete seal between the filter, blue
O-ring, and reservoir.
STEP 5
Fill the reservoir with cold tap water (directly on to the filter) and place
the lid on top. Allow all the water to pass through the filter before filling
again.
STEP 6
Fill your cup and enjoy.
STEP 7
Once your TDS meter reads 006 that means it is time to change your filter.
For Ready-Read products simply turn on your meter(while it is docked within
the spigot) during dispensing and get your instant read, every time.
READY-READ DISPENSERS ONLY (22, 32, 52 cup)
Align the spigot with the hole, push into space until the lock engages, and
you hear an audible click.
Helpful Hint: Wet the blue O-ring before assembly for easier fit.
WHAT IS TDS:
Total Dissolved Solids (“TDS”) are organic and inorganic materials, such as
metals, minerals, salts, and ions dissolved in water. TDS can affect the taste
and appearance of water
HOW TO TEST YOUR WATER:
The included TDS meter measures total dissolved solids in PPM. Use it to
compare Zerowater to tap water and to other water filters
- TEST YOUR TAPWATER
- TEST YOUR OLD PITCHER
- TEST YOUR ZEROWATER
- FILTERED WATER: ZERO
- DISSOLVED SOLIDS
- GUARANTEED*
HOW TO WORK THE METER:
- FOR PRODUCTS WITH READY-READ TECHNOLOGY:
- Simply turn on your meter (while it is docked within the spigot) during dispensing and get your instant read, every time.
FOR PRODUCTS WITHOUT READY-READ TECHNOLOGY:
Remove the cap of the TDS meter, turn it on, and submerge in your freshly
poured glass of water.
(006): Change your filter when the meter reads 006 for the product to continue to perform as represented.
HOW TO READ THE RESULTS
TAP WATER
TDS DESCRIPTION/EXPECTED DURATION OF ZERO WATER FILTER
The higher the influent TDS, the shorter the lifespan of the filter as the filter is working harder to remove more impurities
LEARN HOW THE TDS METER WORKS
TDS meters included with select ZeroWater pitchers/dispensers.
WHAT SETS ZERO WATER APART FROM THE COMPETITION
Additional filtration results of ZeroWater’s 5-Stage Filter vs. conventional 2-StageFilter for Inorganic Chemicals as listed under the EPA’s National Primary Drinking Water Regulations and Contaminants listed under the EPA’s Secondary Drinking Water Standards
METALS
INORGANIC NON-METALS
-
Test results based on NSF/ANSI testing standards of pour-through devices as performed by Quality Filter Testing Laboratory, LLC, located in Williamstown,
New Jersey, an independent ISO 17025 laboratory recognized by IAPMO.
ZeroWater’s 5-stage filter with a rated capacity of 20 Gallons and Brita’s -
Stage Standard Filter with a rated capacity of 40 Gallons was tested under the products’ recommended daily usage of 2 gallons of filtration per day. The results shown are based on an averaged calculation of each filter’s test results of drinking water at a pH level of 6.5 and pH level of 8.5.
-
% reduction after 20 Gallons of Filtration
-
% reduction after 40 Gallons of Filtration
Brita® is a registered trademark of Brita®, L.P, which is not listed with Zero Technologies, LLC
SCAN FOR ADDITIONAL PERFORMANCE RESULTS
PERFORMANCE DATA
- ZeroWater® PERFORMANCE DATA SHEET.
- FOR MODELS: ZD-018, ZP-006, ZP-010, ZD-010RP, ZD-023-1, ZD-012RP,
- ZP-007RP, ZBD-040, ZD-030RP, ZR-0810N, ZR-0810GN, ZD-20RPN, ZS-011RPN,
- ZBD-030, ZD-022-RR, ZP-012-RR, ZD-032-RR, ZD-052-RR
IMPORTANT NOTICE
Read this Performance Data Sheet and compare the capabilities of this unit with your actual water treatment needs. It is recommended that before purchasing a water treatment unit you have your water supply tested to determine your actual water treatment needs. All contaminants reduced by this water treatment device are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary.
This system has been tested according to NSF/ANSI 42 and NSF/ANSI 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in the relevant standard.
The service flow rate is 2.0 gallons per day. The operating temperature is 40-90° F. This water treatment device is intended only for use with potable water. Do not use water that is microbiologically unsafe or of unknown quality without proper disinfection before or after the system.
System Tested and Certified by NSF International against NSF/ANSI Standard 42 for reduction of chlorine taste and odor and against NSF/ANSI Standard 53 for reduction of lead, chromium (Hexavalent), PFOA, PFOS and mercury.
GETTING STARTED
- No need to pre-rinse our filter, we have already done it for you with purified water. This can cause condensation inside the bag or lid, which is harmless.
- This also means there is no shelf life to worry about as long as the bag is not opened, and it is stored in a cool dry place.
NOT GETTING A “000” READING?
- Ensure that the filter is threaded correctly. Watch for cross-threading and ensure that the rubber gasket is seated properly.
- Make sure you are pouring your filtered water into a clean glass.
- The TDS meter may pick up trace residue from previous use or soap if not cleaned properly
For all other issues, please contact our customer service center at
1-800-503-2939 or email
customerservice@zerowater.com.
If you experience any problems or have additional questions, please do not
hesitate to contact our dedicated, live US-based technical support team at:
PRODUCT SUPPORT 1-800-503-2939
CUSTOMERSERVICE@ZEROWATER.COM
Mon-Fri: 8am-8pm CT
LIVE CHAT ZEROWATER.COM
SEE FULL ASSORTMENT OF PRODUCTS AT ZEROWATER.COM
LIMITED WARRANTY
VESSELS & TDS METER
Zero Technologies, LLC warrants the ZeroWater vessels & TDS meter to be free
from manufacturing defects for 90 days from the date of purchase when used in
compliance with the Owner’s Manual. During this 90day period if you discover a
manufacturing defect in the vessel or TDS meter (excluding the filter), we
will replace the parts free of charge.
FILTER CARTRIDGE
Zero Technologies, LLC warrants its filters to be free from manufacturing
defects for 30 days from the date of purchase when used in compliance with the
Owner’s
Manual. During these 30 days, if you discover a manufacturing defect in your
filter, we will provide instructions on how to return the filter for
laboratory testing.
If the lab determines that the filter is defective, we will replace it free of
charge (minus shipping costs). If no defect is found, your filter will be
returned to you, and we will not replace it.
NOTE:
This warranty does not guarantee the life of the filter for any specific
period of volume of use. For more information about expected filter life, see
www.zerowater.com/filtrationfilterlife.
aspx
To file a warranty, claim call, 18005032939 to speak with a customer service
representative. Dated proof of purchase is required for any warranty claim.
Every implied warranty is limited to the duration of this written warranty.
Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from State to State
ZERO WATER REPLACEMENT FILTERS 2-PACK or 4-PACK
store finder at zerowater.com
CONSUMER: Take this coupon to the checkout stand and save $2.50 on a 2-pack or 4-pack of Zero Water Replacement Filters. Limit one coupon per store visit. Offer valid in US only. No doubling of coupon allowed. Coupons cannot be assigned, transferred or reproduced. Coupon good only on product indicated, any other use constitutes fraud. RETAILER: You will be reimbursed for the face value of this coupon plus .08 cents handling allowance if submitted in compliance with Standard Coupon Redemption Policies. The manufacturer reserves the right to request invoices proving the purchase of sufficient stock to cover coupons resented for redemption. Void where taxed, restricted, prohibited, or presented by other than retailers of our products. Cash Value: 1/100th of a cent. The coupon must be redeemed by 12/31/25. MAIL TO: PMCI $2.50 Coupon Offer Dept. 11310, PO Box 5016, Stacy MN 55078-5016. ©2020 Zero Technologies, LLC. Coupons are valid in US only
2-PMPHLTG4-03
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>