amazon basics B08CHGKHYG Teflon Soleplate Steam Iron User Manual

Teflon Soleplate Steam Iron
BO8CHGKHYG, BOSGGLBZWF, BOSGGGLN67

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/ or injury to persons including the following:

READ ALL INSTRUCTIONS BEFORE USING

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a  person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Only use an iron for its intended use.
• To avoid the risk of electric shock, do not immerse the iron in water or other liquids.
• Always turn the iron OFF before plugging or unplugging the iron from the electrical outlet. Never pull on the cord to disconnect the iron from the electrical outlet; instead, grasp the plug and pull on the plug to disconnect the iron.
• Do not let the cord touch hot surfaces. Let the iron cool completely before putting the iron away. Coil the cord loosely around the iron when storing.
• Always disconnect the iron from the electrical outlet before filling the iron with water, emptying the water from the iron, and when the iron is not in use.
• Do not operate the iron with a damaged cord or in the event the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to a qualified serviceman for examination and repair. Incorrect assembly might result in a risk of electric shock when the iron is used after reassembly.
• Close supervision is required for any appliance used by or near children. Do not leave the iron unattended while the iron is connected or on an ironing board.
• Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a STEAM IRON upside down— there might be hot water in the reservoir.
• To avoid a circuit overload, do not operate an iron on the same circuit with another high wattage appliance.
• If an extension cord is absolutely necessary, a cord with an ampere rating equal to or greater than the maximum rating of the iron shall be used. A cord rated for less amperage can result in a risk of fire or electric shock due to overheating. Care shall be taken to arrange the cord so that it cannot be pulled or be tripped over.
• The iron must not be left unattended while it is connected to the supply mains.
• The plug must be removed from the socket-outlet before the water reservoir is filled with water.
• The iron must be used and rested on a flat, stable surface.
• When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.
• The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.
• Keep the iron and its cord out of reach of children less than 8 years of age when it is energized or cooling down.
• The surfaces of the appliance are liable to get hot during use.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Polarized Plug

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified  electrician. Do not modify the plug in any way.

Intended Use

• This product is intended for ironing clothes and fabric.
• This product is intended for household use only.
• This product is intended to be used in dry indoor areas only.
• No liability will be accepted for damages resulting from improper use or noncompliance with these instructions.

Before First Use

DANGER Risk of suffocation!
Keep any packaging materials away from children and pets— these materials are a potential source of danger, e.g. suffocation.

• Remove all the packing materials.
• Remove and review all components before use.
• check the product for transport damages.
• Before connecting the product to the power supply, check that the power supply voltage and current rating corresponds with the power supply details shown on the product rating label.
• Fill water into the water tank, heat up the product at maximum temperature and then iron a piece of scrap cloth for 3 minutes to remove any residue on the soleplate (1).

NOTICE It is normal for the product to release a strange odor when it is first used. The odor will disappear after a while.

Product Description

A Steam burst switch
B Spray switch
C Steam setting knob
D Spray nozzle
E Water inlet cover| F Temperature dial
G Power cable with plug
H Indicator light
I Soleplate
J Measuring cup
---|---

Symbols Explanation

Vertical bursts
Auto off
Anti-drip

**** This symbol stands for “Conformité Européenne”, which declares “Conformity with EU directives, regulations and applicable standards”.
With the CE-marking, the manufacturer confirms that this product complies with applicable European directives and regulation.
This symbol stands for “United Kingdom Conformity Assessed”.
With the UKCA-marking, the manufacturer confirms that this product complies with applicable regulations and standards within Great Britain.

Ironing tips

• Sort the garments that needs to be ironed by fabric type. It minimizes the need to change the temperature settings often.
• Changing the temperature higher or lower both requires time. Wait for approximately 3 minutes after changing the temperature so the desired temperature can be reached.
• If it is unsure what temperature setting to use for a certain type of fabric, use a low temperature setting and increase gradually if needed. Test ironing on a small and less noticeable area or the inside of the item.
• Use an ironing cloth over delicate fabrics (e.g. silk, wool) to prevent shine marks after ironing.
• If the fabric consists of various kinds of fibers, you must always select the lowest ironing temperature to iron the composition of those fibers.
• Velvet and other textures that rapidly become shiny should be ironed in one direction with light pressure applied. Always keep the iron moving at any moment.
• Never iron over zippers and rivets on clothes. This can damage the soleplate (I).
• Read the care label on the garment to determine which temperature setting to use.
  As a reference the symbols are as follows:
  Low heat
  For: acetate, elastane, polyamide, polypropylene etc.
  Medium heat
  For: polyester, silk, triacetate, viscose, wool etc.
  **High heat
  ** For: cotton, linen etc.

Operation

8.1 Filling the water tank

1. Unplug the product from the socket- outlet.
2. Fill the measuring cup (J) with water.
3. Open the water inlet cover (E).
4. Tilt the product backwards at a 45° angle, then pour the water in the water inlet using the measuring cup (J). Do not overfill the water tank above the MAX line.
5. After filling, close the water inlet cover (E). Wipe away any spillage on the product.

NOTICE

• Do not put place liquids other than water (e.g. perfume, vinegar, starch, descaling agent etc.) inside the water tank.
• If the tap water in the household is hard, mix the tap water with equal parts of distilled water or only use distilled water to fill the water tank.

8.2 Ironing
NOTICE It is normal for the indicator light (H) to go on and off while in use. The product is constantly reheating to maintain at the same temperature.

8.2.1 Dry Ironing

1. Place the product on its heel. This is the default position for when the product is preheating or hot but not in use.
2. Connect the plug (G) to a suitable socket-outlet.
3. Rotate the temperature dial (F) to select the desired heat setting . The indicator light (H) lights up, the product is preheating.
4. Preheating is finished when the indicator light (H) goes off. The desired temperature is reached. The product is ready to use.
5. After use, rotate the temperature dial (F) counter-clockwise to the no heat position, then place the product on its heel.
6. Unplug the product from the socket- outlet.
7. Let the product cool completely before storing vertically in a safe place.

8.2.2 Steam ironing
NOTICE This function cannot be used on low heat ( • ) setting and is not suitable for delicate fabrics.

1. Fill the water tank.

2. Place the product on its heel. This is the default position for when the product is preheating or hot but not in use.

3. Connect the plug (G) to a suitable socket-outlet.

4. Rotate the temperature dial (F) to select the medium or high heat setting . The indicator light (H) lights up, the product is preheating.

5. Preheating is finished when the indicator light (H) goes off. The desired temperature is reached. The product is ready to use.

6. Set the steam settings knob (C) to the desired setting. The steam is released from the holes on the soleplate (I).
   – Steaming function on
   – Steaming function off

7. After use, switch off the steam and rotate the temperature dial (F) counter-clockwise to the no heat position then place the product on its heel.

8. Unplug the product from the socket-outlet.

9. Empty the water tank.

10. Let the product cool completely before storing vertically in a safe place.

8.3 Spraying
This function can be used at any time and it does not affect other functions.

1. Fill the water tank.
2. Aim the spray nozzle (D) at the garment.
3. Press the spray switch (B) to release some water droplets.

NOTICE It may take a few presses to start spraying if water is newly added to the water tank.

8.4 Burst of steam
A burst of steam provides extra steam to remove stubborn wrinkles. It can be used at any time and it does not affect other functions.

NOTICE

• It may take a few presses to start the bursts of steam if water is newly added to the water tank.
• Do not use burst of steam more than 3 times in succession.

8.4.1 Horizontal bursts

1. Fill the water tank and preheat the product to .

2. When preheating is done, press the soleplate (I) on the stubborn wrinkles.

3. Press the steam burst switch (A).
   The product releases a strong burst of steam penetrating through the garment to remove the wrinkles.

4. If the wrinkles still remain, wait for a few seconds then press the steam burst switch (A) again.

8.4.2 Vertical bursts
WARNING  Risk of burns!
Do not apply steam on any clothing that are being worn by humans or pets. The steam can penetrate through the fabric and cause burns.

1. Fill the water tank and preheat the product to .

2. When preheating is done, hold the product vertically between 6 — 12” (15 — 30 cm) away from the garment.

3. Press the steam burst switch (A).
   The product releases a strong burst of steam penetrating through the garment to remove the wrinkles.

4. If the wrinkles still remain, wait for a few seconds then press the steam burst switch (A) again.

8.5 Automatic shut-off
As a Safety feature, the product would automatically shut off after a period of inactivity. The product makes beep sounds and the indicator light (H) flashes when automatic shut-off is functioning. Automatic shut-off happens if:

• The product is in a horizontal position for 30 seconds.
• The product is in a side position for 30 seconds.
• The product is in a vertical position for 8 minutes.
  To return the product to heating, pick up or move it slightly. The product stops flashing and preheats again for normal use.

Cleaning and Maintenance

WARNING Risk of electric shock!

• To prevent electric shock, unplug the product before cleaning.
• During cleaning do not immerse the product in water or other liquids. Never hold the product under running water.

NOTICE The soleplate (I) should not come into contact with hard metal objects.
Never use a souring pad, vinegar or other chemical to clean it.

9.1 Emptying the water tank
WARNING Risk of burns!
The product can be hot after use. Do not touch the soleplate (I) unless it has cooled completely.

After every use, pour away the remaining water in the water tank.

1. Unplug the product from the socket-outlet.
2. Open the water inlet cover (E) and pour out the water in water tank.
3. Shake the product to remove any remaining water.

9.2 Storage
Store the product in its original packaging in a dry area. Keep away from children and pets.

9.3 Maintenance
Any other servicing than mentioned in this manual should be performed by a professional repair center.

Troubleshooting

socket outlet. Use voltage tester to verify if the socket outlet is powered.
For UK only: Fuse in the plug is blown.| • Use a flat screwdriver to open the fuse compartment cover. Remove the fuse and replace with the same type (10 A, BS1362). Refit the cover.
No spray mist coming out from the spray nozzle (D).| • Mist might not spray out immediately, press a few more times until the spray mist comes  out.
• The water tank is empty. Fill the water tank.
Soleplate(I) is not hot enough.| • The temperature setting is set too low. Increase the temperature setting using the temperature dial (F).
• If the indicator light (H) is on, the product is preheating. Wait for the indicator to go off, this means the product has reached desired temperature.
The garment is damaged.| • The temperature setting is too high. Follow the care label on the garment and use the recommended temperature settings.
Flakes and scale come out from the soleplate (I) holes during ironing.| • Hard water is causing the formation of flakes and scale. Use the self-cleaning function to remove the flakes and scale before using.

Disposal (for Europe only)

**** The Waste Electrical and Electronic Equipment (WEEE) laws aim to minimise the impact of electrical and electronic goods on the environment and human health, by increasing re-use and recycling and by reducing the amount of WEEE going to landfill. The  symbol on this product or its packaging signifies that this product must be disposed separately from ordinary household wastes at its end of life. Be aware that this is your responsibility to dispose of electronic equipment at recycling centres in order to conserve  natural resources. Each country should have its collection centres for electrical and electronic equipment recycling. For information about your recycling drop off area, please contact your related electrical and electronic equipment waste management authority, your local city office, or your household waste disposal service.

Specifications

12.1 North American market (BO8CHGKHYG)

12.2 European market (BOSGGLBZWF, BO8GGGLN67)

12.3 Importer Information

| For EU
---|---
Postal:| Amazon EU S.ar.L, 38 avenue John F. Kennedy, L-1855 Luxembourg
Business Reg.:| 134248
| For UK
Postal:| Amazon EU SARL, UK Branch, 1 Principal Place, Worship St, London EC2A 2FA, United Kingdom
Business Reg.:| BRO17427

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.
Scan QR Code below with your phone camera or QR reader:
US:

https://www.amazon.com/review/review-your-purchases/listing/?ref=HPB_UM_CR

UK: amazon.co.uk/review/review-your- purchases#
If you need help with your Amazon Basics product, please use the website or number below.
US: amazon.com/gp/help/customer/contact- us
UK: amazon.co.uk/gp/help/customer/contact- us
+1 877-485-0385 (US Phone Number)

MADE IN CHINA
VO2-08/23

Documents / Resources

| amazon basics B08CHGKHYG Teflon Soleplate Steam Iron [pdf] User Manual
B08CHGKHYG Teflon Soleplate Steam Iron, B08CHGKHYG, Teflon Soleplate Steam Iron, Soleplate Steam Iron, Steam Iron, Iron
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>