BARSKA BC362 GLX Green 5mW Tactical Laser Sight Instruction Manual
- June 14, 2024
- BARSKA
Table of Contents
BARSKA BC362 GLX Green 5mW Tactical Laser Sight
GLX Green 5mW Tactical Laser Sight with Picatinny Rail and 1” Ring
Description
BARSKA’s 5mW Green Laser Sight GLX features external riflescope style
windage and elevation (W/E) adjustments for quick, high precision targeting.
Zeroing in your laser is a quick and easy process. The tactical design
integrates a tactical edged bezel into the strong T6 aluminum body for added
protection. The diamond cut exterior grip improves the mounting capability of
the picatinny 1” mounting ring included with the laser sight.
WARNING : BE CERTAIN THAT YOUR FIREARM IS NOT LOADED AND POINTED AWAY FROM YOU IN A SAFE DIRECTION- ATTENTION : THIS BARSKA LASER SIGHT IS A POWERFUL TARGETING DEVICE THAT REQUIRES SPECIAL ATTENTION WHEN OPERATING. CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND SAFETY PRECAUTIONS BEFORE USING THIS PRODUCT.
- CAUTION : UNAUTHORIZED USE MODIFICATIONS OF ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN SPECIFIED HEREIN MAY RESULT IN DANGEROUS/HAZARDOUS RADIATION EXPOSURE.
- LASER LIGHT: AVOID DIRECT EYE EXPOSURE. WARNING KEEP OUT OF REACH OF CHILDREN. DO NOT POINT LASER AT PEOPLE, PETS, AIRPLANES, SHINY/HIGHLY REFLECTIVE SURFACES, OR ANY OTHER OBJECT NOT INTENDED FOR DESIGNATED USE.
MOUNTING
Your laser sight is equipped with a Picatinny Rail. This rail will attach your laser to your firearm.
- Slide the laser sight into the bore of the Picatinny rail.
- Once the sight is in the rail tighten it in place by using an Allen wench.
- Slide the rail onto your firearm, then tighten it in place.
BATTERY
This device is powered by one 3v (CR123A) Lithium Battery.
- Unscrew the cable switch by turning it counter clockwise
- Insert the battery so that the positive pole of the battery faces out.
- Replace the switch back on the laser sight. Turn clockwise to tighten the cable switch onto the sight. Make sure that you have screwed the switch on tightly.
WINTAGE & ELEVATION
Adjustments must be made in the shooter’s position of the sight. This laser sight has been factory calibrated. Should you require adjusting the windage and elevation remove turret caps and see chart below to distinguish which of these knobs you need to turn and in which direction. CC: Counter Clockwise C: Clockwise
| Up| Down| Left| Right
---|---|---|---|---
Elevation| C| CC| |
Windage| | | CC| C
ASSESORIES INCLUDED
- Continuous push button on/off cap
- 1” picatinny rail ring with removable cross-bar
- •Momentary on/off long cable switch
- 1” High Dovetail .22/Airgun Ring
NOTE
- After 3 minutes of continuous use, turn laser off for 1 minute
- If operating laser in cold weather (under 68˚ F) let laser warm up by turning it on for 30 seconds before use. (Actual warm up time may vary depending on surrounding environment)
- Test laser periodically during periods of non-usage to ensure adequate battery level
TECHNICAL DATA
BVisible Laser Class IIIA Laser Product
- Length
- 138mm
- Weight
- 204g
- Main Tube Diameter
- 1 inch
- Output Power
- <5mW
- Wavelength
- 532(±10)nm
- Reach
- 1000 YDS
- Operating Temperature
- 59˚F-95˚F
- Adjustment
- Windage & Elevation
- MaterialT6
- Aluminum
- Battery Type
- CR-123A Lithium
WARNING:
- AVOID EXPOSURE LASER RADIATION IS EMITTED FROM THIS APERTURE
- LASER RADIATION AVOID DIRECT EYE EXPOSURE
- Max Output<5mW WAVELENGTH 532(±10)nm Class IIIA Laser Product FDA NO.:0720007
- This product complies with 21 CFR chapter 1, subchapter
- 5mW Green Laser Sight w/ring Model: AU11368 Made In China Manufactured on 08/2013 BARSKA Optics 855 Towne Center Drive Pomona, CA 91767
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>