ALBRECHT ATR 430 Horse Riding Set User Manual
- June 14, 2024
- ALBRECHT
Table of Contents
ALBRECHT ATR 430 Horse Riding Set
Delivery content
The following accessories are included in the scope of delivery of the Albrecht Horse Riding set:
For the student:
- ATR 430 wireless receiver
- 4 silicon earhooks in different sizes
- Neckholder
- Hygenic silicone earcover
- Water protection bag for the receiver
- Micro-USB charging cable
For the trainer:
- ATT 400 transmitter
- Clip mikrophone
- Lanyard
- Belt clip
- Twin USB charger to charge the transmitter and receiver simultaneously
- Charging cable for transmitter
- Softshell transportation bag
Overview
Please familiarise yourself with all the functions of your radio.
Buttons and functions – ATT 400 transmitter
Buttons and functions – ATT 430 receiver
Operation
Charging
All units should be charged completely before using them the first time. The
units should be turned off before charging and it will take about 3-4 hours to
fully charge them. The red LED will be flashing during charging and will stop
once finished charging.
Turn the unit on/off
- To turn on the unit, push the “ON/OFF” button on the right side of the unit down. The status of the signal strength, battery level, volume and channel will be displayed on the screen.
- The receiver is switched on via the ****button on the underside. Press and hold the button for approx. 3 seconds until the LED lights up blue.
Connection the microphone to the transmitter
Insert the plug of the microphone on the top of the unit into the „MIC“
socket. The microphone can be attached with the clip, e.g. to a shirt collar.
It should be placed as close to the mouth as possible to ensure the best audio
quality.
Adjusting the volume at the receiver
- By default, the key lock is enabled on the receivers to avoid accidentally changing any settings. Press and hold the M key for 3 seconds to deactivate the key lock.
- Press “Vol-” button to decrease the volume.
- Press “Vol+” button to increase the volume.
- The volume setting on the transmitter has no function.
Create Tourist Groups / Manage the Receivers (only for Tourist Guide Transmitter ATT400 available)
- Before you start using the receivers and transmitter, you will have to create a group of units. Therefore turn on all units you want to be in one group. Select a channel which is currently not used (for example if you have several tourist groups in a Museum) on the ATT400 transceiver.
- Make sure that all receivers of your group are within the range of 150m. Then press and hold the function button “CONF.” for 5 seconds on the transceiver. The channel of all receiver units will automatically change to the same channel as selected on the transceiver. All receivers are now assigned to your group.
- If one or several students accidentally change the channel and cannot hear the trainer anymore, just press the “CONF.” button again for 5 seconds and all receiver units are synchronised to your channel again.
Notice:
- All receivers which are once assigned to a group, can only be managed by its original transmitter. Management function of other transmitters will not affect these units.
- DO NOT use the same channel for different groups at the same place and the same time..
Change channel manually
Normally your trainer will manage all channels and you do not have to change
it manually. Should it be necessary anyway, follow these steps:
- Press the menu button „M“ for approx. 3 seconds to deactivate the key lock.
- Press and hold the menu button „M“ again for 1 second to activate channel selection
- Select one of the 50 channels by pressing the „+/-“ buttons on the top side
- Press the function button menu button „M“ again to confirm the selected channel.
Installation of the receiver
- Depending on the shape of the ear and how it feels to wear it, the training set can be attached either with the different-sized ear hooks or with the neckholder. The neckholder is placed behind the head with the fastening clip on the right side. The ear hooks are slid over the ear from front to back until they fit snugly.
- The receiver must always be worn on the right ear with the speaker opening facing forward.
Note: The more precisely the receiver sits in the ear, the clearer you will hear the voice announcements. If you want to change the holder, simply pull it carefully off the unit and then clip on another holder.
Technical specification
ATR 430 Receiver|
---|---
Frequency Range| 2.4GHz: 2400 – 2480 MHz
Operating Range| up to 200m
Channels| 50
Earphone Sensitivity| 75db
Earphone Impedance| 32 Ohm
Earphone Power| 0.5W
Battery Type| Built-In Lithium Battery
Battery Working Time| 8-10 hours after full charging
Battery Feature| 3.7V / 300mAh / Working current: 40 – 50mA
Sensitivity| -102dbm
Frequency Response| 50 Hz – 12 KHz
Dimensions| 70x20x25mm
Weight| 18g
ATT 400 Transmitter|
---|---
Frequency Range| 2.4GHz: 2400 – 2480 MHz
Operating Range| up to 200m
Channels| 50
Mic Sensivity| -38db
Mic Impedance| 32 Ohm
Mic Frequency Response| 75 Hz – 8 Khz
Battery Type| Built-In Lithium Battery
Battery Working Time| 8-10 hours after full charging
Battery Feature| 3.7V / 1500mAh / Working current: 170-200mA
RF Output Power| 10mW
Frequency Response| 50 Hz – 12 KHz
Dimensions| 86x50x19mm
Weight| 68g
Warranty and Recycling Information
We are legally obliged to include disposal and warranty information as well as EU declaration of conformity with the use instructions in different countries for every unit. Please find this information on the following pages.
2-Year Warranty from Date of Purchase
- The manufacturer/retailer guarantees this product for two years from date of purchase. This warranty includes all malfunctions caused by defective components or incorrect functions within the warranty period excluding wear and tear, such as exhausted batteries, scratches on the display, defective casing, broken antenna and defects due to external effects such as corrosion, over voltage through improper external power supply or the use of unsuitable accessories. Defects due to unintended use are also excluded from the warranty.
- Please contact your local dealer for warranty claims. The dealer will repair or exchange the product or forward it to an authorized service center. You can also contact our service partner directly. Please include your proof of purchase with the product and describe the malfunction as clearly as possible.
WEEE and Recycling
The European laws do not allow any more the disposal of old or defective
electric or electronic devices with the household waste. Return your product
to a municipal collection point for recycling to dispose of it. This system is
financed by the industry and ensures environmentally responsible disposal and
the recycling of valuable raw materials.
Service Address And Technical Hotline (for units sold in Germany)
- Alan Electronics GmbH
- Service
- Daimlerstraße 1g
- 63303 Dreieich
- Germany
- Contact our service hotline by phone +49 (0) 6103 9481 66 (regular costs for German fixed network) or e-mail at service@albrecht-midland.de
Declaration of Conformity
- Hereby, Alan Electronics GmbH declares that the radio equipment type ATR 430 / ATT 400 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://service.alan-electronics.de/CE-Papiere/
- Printing errors reserved.
- Information in this user manual are subject to change without prior notice.
- © 2023 Alan Electronics GmbH – Daimlerstraße 1g – 63303 Dreieich – Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>