SONOFF MINIR4 WiFi Smart Switch User Guide
- June 14, 2024
- SonOFF
Table of Contents
SONOFF MINIR4 WiFi Smart Switch
Power off
Please install and maintain the device by a professional electrician.
To avoid electric shock hazard, do not operate any connection or contact the
terminal connector while the device is powered on!
Wiring instruction
- No matter S1 and S2 are connected or left idle to the external switch, this device can be controlled by automation or the App.
- It is prohibited to connect S1 and S2 terminals to the neutral or ground wire, in order to avoid damaging the equipment and causing danger.
- Make sure all wires are connected correctly.
Download the eWeLink App
Power on
After powering on, the device will enter the Pairing Mode during the first use. The LED indicator changes in a cycle of two short and one long flash.
The device will exit the Pairing Mode if not paired within 10mins.
If you want to enter this mode, please long press button for about 5s until
the LED indicator changes in a cycle of two short and one long flash and
release.
Add device
Tap “+” and select “Add Device”, then operate following the prompt on the App
It’s required to turn on the Bluetooth on your Phone when adding a device.
Add eWeLink-Remote Sub-devices
Enter the Device Settings page on the eWeLink App, select “eWeLink-Remote sub- devices” and tap “Add”, then trigger the sub-device to add it successfully.
User Manual
Scan the QR code or visit the website to learn about the detailed user manual and help. ****
FCC compliance statement
-
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
-
This device may not cause harmful interference, and
-
This device must accept any interference received, including interference
that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES – 003(B).
This device complies with RSS – 247 of Industry Canada. Operation is subject
to the condition that this device does not cause harmful interference.
SAR Warning
Under normal use of condition, this equipment should be kept a separation
distance of at least 20 cm between the antenna and thebody of the user.
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type MINIR4 is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address:
For CE Frequency:
Operation frequency Range:
- BLE: 2402-2480MHz
- Wi-Fi: 2412-2472MHz
- RF Output Power:
- BLE: 1.87dBm
- Wi-Fi: 16.12dBm(802.11b),15.80dBm(802.11g), 15.67dBm(802.11n20), 13.33dBm(802.11n40)
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste. Instead, you should protect human health and the environment
by handing over your waste equipment to a designated collection point for the
recycling of waste electrical and electronic equipment, appointed by the
government or local authorities. Correct disposal and recycling will
helpprevent potential negative consequences to the environment and human
health. Please contact the installer or localauthorities for more information
about the location as well as terms and conditions of such collection points.
Shenzhen Sonoff Technologies Co., Ltd.
- 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
- ZIP code: 518000
- Website: sonoff.tech.
- Service email: support@itead.cc.
- MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>