SKYWORTH WXT2IM2511 WIFI BT Module Instructions

June 15, 2024
SKYWORTH

SKYWORTH WXT2IM2511 WIFI BT Module

Product Descrition

This document is to specify the product requirements for 802.11a/b/g/n/ac/ax and Bluetooth USB Module.This Card is based on MediaTek MT7921 chipset .It is a complete multi-band(2.4GHz and 5GHz)WIFI 2 ×2 MIMO MAC/PHY/Radio System- on-a-Chip. This module provides a high level of integration with adual-stream IEEE 802.11ax MAC/ base band /radio.The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 1201Mbps. It is also backward complied with IEEE 802.11a standardfrom 5.15~5.825GHz wideband and IEEE 802.11b/g standard from 2.4~2.5GHz. It can be used to provideup to 54Mbps for IEEE 802.11a and IEEE 802.11g, 11Mbps for IEEE 802.11b and 300Mbps for IEEE802.11n. The Bluetooth part supports latest 5.2 .  With seamless roaming, fully interoperability and advanced security with WEP standard, 802.11 a/b/g/n/ac/axUSB2.0/USB3.0 Module offers absolute interoperability with different vendors 802.11a/b/g/n/ac/ax. Access Points through the wireless LAN.

Product Features

  • Compatible with IEEE 802.11a standard to provide wireless 54Mbps data rate
  • Compatible with IEEE 802.11b standard to provide wireless 11Mbps data rate
  • Compatible with IEEE 802.11g standard to provide wireless 54Mbps data rate
  • Compatible with IEEE 802.11n standard to provide wireless 300Mbps data rate
  • Compatible with IEEE 802.11ac standard to provide wireless 866.7Mbps date rate.
  • Compatible with IEEE 802.11ax standard to provide wireless 1201Mbps data rate.
  • Operation at 2.4~2.5GHz and 5.15~5.825GHz frequency band to meet worldwide regulations.
  • Support MU-MIMO RX.
  • Bluetooth specification 2.1+EDR
  • Bluetooth 5.2 Low Energy (LE)
  • IEEE 802.11 d/e/h/i/j/k/mc/r/v/w support
  • Security support for WFA WPA/WPA2/WPA3 personal, WPS2.0, WAPI
  • Drivers support Win10,Win8,Win7,XP,Linux
  • High speed USB 2.0 interface
  • High speed USB 3.0 interface
  • HSF compliant

Product Specification

Operating Voltage 5V±10%
Current Consumption <2000mA
Antenna Type PIFA Antenna

Operating

Temperature

| ****

0 ~ 70°C ambient temperature

Storage Temperature| -40 ~ 80°C ambient temperature

NOTICE

  • please keep this product and accessories attached to the places which children can’t touch;
  • do not splash water or other liquid onto this product, otherwise it may cause damage;
  • do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
  • please keep this product away from flammable or naked flame;
  • please do not repair this product by yourself. Only qualified personnel can be repaired.

Antenna description

The DUT supports Bluetooth, 2.4 and 5GHz functions, and there is only one antenna type. The information is as follows. PIFA antenna and module are permanently connected. 1) PIFA Antenna, Bluetooth peak gain 1.85dbi, 2.4G peak gain 1.56dbi/Ant1 and 3.33dbi/Ant2, 5G peak gain 3.41 dBi/Ant1 and 4.77 dBi/Ant2.

Federal Communication Commission Interference Statement

USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio- frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT
The final end product must be labeled in a visible area with the following ” Contains FCC ID: 2BAD6-7METZIFPD “. If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesiredoperation.

IMPORTANT NOTE

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without C2PC. This module is intended for OEM integrator. The OEM integrator isresponsible for the compliance to all the rulesthat apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. Industry Canada Statement The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

RSS-Gen Section 8.4 User manual notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.This device isintended only for OEM integrators underthe following conditions: (For module device use)
  3. The antenna must be installed such that 20 cm is maintained between the antenna and users, and
  4. The transmitter module may not be co-located with any other transmitter or antenna.

As long as 2 conditions above are met, further transmitter test will not be required. However,the OEM integrator is stillresponsible for testing their end-product for any additional compliance requirements required with this module installed.

IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter),then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.

Manual Information To the End User
The OEM integrator hasto be aware not to provide information to the end user regarding how to install orremove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals