CUTECH 40700H-CT 12-1-2 Inch Spiral Cutter Head Planer User Guide
- June 5, 2024
- CUTECH
Table of Contents
CUTECH 40700H-CT 12-1-2 Inch Spiral Cutter Head Planer User Guide
INTRODUCTION
This user manual is intended for use by anyone working with this machine. It
should be kept available for immediate reference so that all operations can be
performed with maximum efficiency and safety. Do not attempt to perform
maintenance or operate this machine until you have read and understand the
information contained in this manual.
The drawings, illustrations, photographs, and specifications in this user
manual represent your machine at time of print. However, changes may be made
to your machine or this manual at any time with no obligation to CUTECH.
WARRANTY
2 YEAR LIMITED WARRANTY
CUTECH warrants its machinery to be free of defects in workmanship and materials for a period of two (2) years from the date of the original purchase by the original owner. This warranty applies to products sold in the United States only. The warranty does not apply to any product used for professional or commercial production purposes nor for industrial or educational applications. Such cases are covered by our 1 year Limited Warranty with the Conditions and Exceptions.
Warranty does not include failures, breakage or defects deemed after inspection by an Authorized Service Center or our agent to have been directly or indirectly caused by or resulting from improper use, lack of or improper maintenance, misuse or abuse, negligence, accidents, damage in handling or transport, or normal wear and tear of any part or component. Examples are consumables such as inserts and knives or wear items like drive belts, bearings or brushes. Additionally, warranty is void if repairs or alterations are made to the machine by an unauthorized service center without the direct consent of CUTECH.
To file a claim of warranty or to find a service center, call
858-886-7333 or email
support@cutechtools.us.
Warranty applies to the original buyer only and may not be transferred. You
will need to furnish with your claim a copy of the original sales receipt as
proof of purchase and the serial number from the machine.
The defective units should be returned Freight prepaid to CUTECH’s Authorized Service Center for inspection. If the warranty claim is considered to be invalid due to exclusions listed above, CUTECH will at your direction dispose of or return the product. In the event you choose to have the product returned, you will be responsible for the handling and shipping cost of the return.
CUTECH furnishes the above warranties in lieu of all other warranties, express or implied. CUTECH shall not be liable for any special, indirect, incidental, punitive or consequential damages, including without limitation loss of profits arising from or related to the warranty, the breach of any agreement or warranty, or the operation or use of its machinery, including without limitation damages arising from damage to fixtures, tools, equipment, parts or materials, direct or indirect loss caused by any other part, loss of revenue or profits, financing or interest charges, and claims by and third person, whether or not notice of such possible damages has been given to CUTECH. Not responsible for damages of any kind for any delay by or failure of CUTECH to perform its obligations under this agreement or claims made a subject of a legal proceeding against CUTECH more than one (1) year after such cause of action first arose.
The validity, construction and performance of this Warranty and any sale of machinery by CUTECH shall be governed by the law of the State of California, without regard to conflicts of laws provisions of any jurisdiction. Any action related in any way to any alleged or actual offer, acceptance or sale by CUTECH or any claim related to the performance of and agreement including without limitation this Warranty, shall take place in the federal or state courts in San Diego, California.
CUTECH reserves the right to change the specification without prior notice. PRODUCT SPECIFICATIONS
Feed speed F/min 26 FPM
Cutterhead speed RPM 10,000
Motor RPM 23000+/-10% (No Load)
Cutterhead diameter 2”
Max planer capacity 6″ x 12-1/2″
Max depth of cut @ 6” 3/32″
Max depth of cut @ 12-1/2” 1/16″
Minimum Length of Stock 7”
Minimum Thickness of Stock 3/16”
Cutter Inserts Qty 24
Motor power input 120V, 60 Hz, AC Only, 15 Amp
ShippingWeight 60.5lbs
Shipping Dimensions 25” W x 15” D x 18” H
Product Dimensions 22 1/16” W x 28” D (w/ tables) x 16 1/32” H (w/o handle)
Dust Port Opening 2”
FEATURE IDENTIFICATION
GENERAL SAFETY
NOTE: The WARNING! and CAUTION! symbols indicate a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. READ THIS MANUAL completely before assembling and operating this machine.
WARNING! TO AVOID serious injury, death, or damage to the machine, please read, understand, and follow, all Safety and Operating Instructions before assembling and operating this machine. This manual is not totally comprehensive. It does not and can not convey every possible safety and operational problem which may arise while using this machine. The manual will cover many of the basic and specific safety procedures needed in an industrial environment.
All federal and state laws, and any regulations having jurisdiction covering the safety requirements for use of this machine, take precedence over the statements in this manual. Users of this machine must adhere to all such regulations.
WARNING! Exposure to the dust created by power sanding, sawing, grinding, drilling and other construction activities may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. The dust may contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
- Lead from lead-based paints.
- Crystalline silica from bricks, cement and other masonry products.
- Arsenic and chromium from chemically-treated lumber.
Always operate tool in well ventilated area and provide for proper dust removal. Use a dust collection system along with an air filtration system whenever possible. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.
WARNING! ALWAYS wear eye protection. Any machine can throw debris into the eyes during operations, which could cause severe and permanent eye damage. Everyday eyeglasses are NOT safety glasses. ALWAYS wear Safety Goggles (that comply with ANSI standard Z87.1) when operating power tools.
WARNING! ALWAYS wear hearing protection. Plain cotton is not an acceptable protective device. Hearing equipment should comply with ANSI S3.19 Standards.
WARNING! ALWAYS wear a NIOSH/OSHA approved dust mask to prevent inhaling dangerous dust or airborne particles.
ALWAYS keep the work area clean, well lit, and organized. DO NOT work in an area that has slippery floor surfaces from debris, grease, and wax.
CAUTION! ALWAYS unplug the machine from the electrical receptacle when making adjustments, changing parts or performing any maintenance.
AVOID ACCIDENTAL STARTING. Make sure that the power switch is in the “OFF” position before plugging in the power cord to the electrical receptacle.
WARNING! AVOID a dangerous working environment. DO NOT use electrical tools in a damp environment or expose them to rain or moisture.
WARNING! CHILDPROOF THE WORKSHOP AREA by removing switch keys, unplugging tools from the electrical receptacles, and using padlocks.
CAUTION! DO NOT use electrical tools in the presence of flammable liquids or gasses.
DO NOT FORCE the machine to perform an operation for which it was not designed. It will do a safer and higher quality job by only performing operations for which the machine was intended.
WARNING! DO NOT stand on a machine. Serious injury could result if it tips over or you accidentally contact any moving part.
DO NOT store anything above or near the machine.
WARNING! DO NOT operate any machine or tool if under the influence of drugs, alcohol, or medication.
EACH AND EVERY time, check for damaged parts prior to using any machine. Carefully check all guards to see that they operate properly, are not damaged, and perform their intended functions.
Check for alignment, binding or breakage of all moving parts. Any guard or other part that is damaged should be immediately repaired or replaced.
WARNING! Ground all machines. If any machine is supplied with a 3-prong plug, it must be plugged into a 3-contact electrical receptacle. The third prong is used to ground the tool and provide protection against accidental electric shock. DO NOT remove the third prong.
CAUTION! Keep visitors and children away from any machine. DO NOT permit people to be in the immediate work area, especially when the machine is operating.
KEEP protective guards in place and in working order.
CAUTION! MAINTAIN your balance. DO NOT extend yourself over the tool. Wear oil resistant rubber soled shoes. Keep floor clear of debris, grease, and wax.
MAINTAIN all machines with care. ALWAYS KEEP machine clean and in good working
order.
KEEP all blades and tool bits sharp.
NEVER leave a machine running, unattended. Turn the power switch to the OFF
position. DO
NOT leave the machine until it has come to a complete stop.
REMOVE ALL MAINTENANCE TOOLS from the immediate area prior to turning the machine ON.
WARNING! STAY ALERT, watch what you are doing, and use common sense when operating any machine. DO NOT operate any machine tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
WARNING! USE ONLY recommended accessories. Use of incorrect or improper accessories could cause serious injury to the operator and cause damage to the machine. If in doubt, DO NOT use it.
THE USE of extension cords is not recommended for 230V equipment. It is better
to arrange the placement of your equipment and the installed wiring to
eliminate the need for an extension cord.
If an extension cord is necessary, refer to the chart in the Grounding
Instructions section to determine the minimum gauge for the extension cord.
The extension cord must also contain a ground wire and plug pin.
CAUTION! Wear proper clothing, DO NOT wear loose clothing, gloves,
neckties, or jewelry.
These items can get caught in the machine during operations and pull the
operator into the moving parts. Users must wear a protective cover on their
hair, if the hair is long, to prevent it from contacting any moving parts.
SAVE these instructions and refer to them frequently and use them to instruct other users.
NOTE: Information regarding the safe and proper operation of this tool is also available from the following sources:
Power Tool Institute
1300 Summer Avenue
Cleveland, OH 44115-2851
www.powertoolinstitute.org
National Safety Council
1121 Spring Lake Drive
Itasca, IL 60143-3201
American National Standards Institute
23 West 43rd Street, 4th Floor
New York, NY 10036
www.ansi.org
ANSI 01.1 Safety Requirements for
Woodworking Machines and the
U.S. Department of Labor Relations
www.osha.gov
PRODUCT SAFETY
-
Serious personal injury may occur if normal safety precautions are overlooked or ignored.
Accidents are frequently caused by lack of familiarity or failure to pay attention. Obtain advice from supervisor, instructor, or another qualified individual who is familiar with this machine and its operations. -
Every work area is different. Always consider safety first, as it applies to your work area.
Use this machine with respect and caution. Failure to do so could result in serious personal injury and damage to the machine. -
Prevent electrical shock. Follow all electrical and safety codes, including the National Electrical Code (NEC) and the Occupational Safety and Health Regulations (OSHA). All electrical connections and wiring should be made by qualified personnel only
-
WARNING! TO REDUCE the risk of electrical shock. DO NOT use this machine outdoors.
DO NOT expose to rain. Store indoors in a dry area. -
STOP using this machine, if at any time you experience difficulties in performing any operation. Contact your supervisor, instructor or machine service center immediately.
-
Safety decals are on this machine to warn and direct you to how to protector yourself or visitors from personal injury. These decals MUST be maintained so that they are legible. REPLACE decals that are not legible.
-
DO NOT leave the unit plugged into the electrical outlet. Unplug the unit from the outlet when not in use and before servicing, performing maintenance tasks, or cleaning.
-
WARNING! DO NOT handle the plug or planer with wet hands
-
USE only accessories as described in this manual and recommended by CUTECH.
-
DO NOT pull the planer by the power cord. NEVER allow the power cord to come in contact with sharp edges, hot surfaces, oil or grease.
-
ALWAYS turn the power switch “OFF” before unplugging the planer.DO NOT unplug the planer by pulling on the power cord. ALWAYS grasp the plug, not the cord.
-
REPLACE a damaged cord immediately. DO NOT use a damaged cord or plug.
-
DO NOT use the planer as a toy. DO NOT use near or around children.
-
ENSURE that the machine sits firmly before using. If the machine wobbles or is unstable, correct the problem by using shims or blocks prior to operation.
-
This machine is designed to process wood ONLY.
-
WARNING! NEVER position fingers or thumbs near the infeed/ outfeed rollers or cutterhead.
-
Long pieces of stock should ALWAYS be supported with some type of fixture.
-
DO NOT operate planer with dull or damaged blades.
-
MAKE CERTAIN that the planer is properly adjusted prior to use.
-
DO NOT try and remove excessive amounts of wood in one single pass.
-
INSPECT all stock before planing, ensuring that there are no foreign objects embedded in the wood, loose knots, or knots that may become loose during operation.
-
WARNING! DO NOT attempt to remove jams until power is disconnected and all moving parts have come to a complete stop.
-
MAKE SURE that there is adequate operating space on both the infeed and outfeed sides of the planer before operating.
-
DO NOT attempt to plane wood that is less than 7” long or less than 3/16” thick.
GROUNDING INSTRUCTIONS
WARNING! This machine MUST BE GROUNDED while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, GROUNDING provides the path of least resistance for electric current and reduces the risk of electric shock. The plug MUST be plugged into a matching electrical receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.
If a plug is provided with your machine DO NOT modify the plug. If it will not fit your electrical receptacle, have a qualified electrician install the proper connections to meet all electrical codes local and state. ALL connections must also adhere to NEC and OSHA mandates.
WARNING! IMPROPER ELECTRICAL CONNECTION of the equipment grounding conductor can result in risk of electric shock. The conductor with the green insulation (with or without yellow stripes) is the equipment-grounding conductor. DO NOT connect the equipment-grounding conductor to a live terminal if repair or replacement of the electric cord or plug is necessary.
Check with a qualified electrician or service personnel if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded.
WARNING! Electrocution or fire could result if this machine is not grounded properly or if the electrical configuration does not comply with local and state electrical codes.
MAKE CERTAIN the machine is disconnected from power source before starting any electrical work.
MAKE SURE the circuit breaker does not exceed the rating of the plug and receptacle.
The motor supplied with your machine is a 115 volt, 60 hertz, single phase motor. Never connect the green or ground wire to a live terminal. A machine with a 115 volt plug should only be connected to an outlet having the same configuration as the plug.
WARNING! To reduce the risk of fire or electrical shock, use the proper gauge of extension cord. When using an extension cord, be sure to use one heavy enough to carry the current your machine will draw.
The smaller the gauge-number, the larger the diameter of the extension cord is. If in doubt of the proper size of an extension cord, use a shorter and thicker cord. An undersized cord will cause a drop in line voltage resulting in a loss of power and overheating.
CAUTION! USE ONLY a 3-wire extension cord that has a 3-prong grounding plug and a 3-pole receptacle that accepts the machine’s plug. If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use.
Make certain the extension cord is properly sized, and in good electrical condition. Always replace a worn or damaged extension cord immediately or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
MINIMUM RECOMMENDED GAUGE FOR EXTENSION CORDS (AWG)
120 VOLT OPERATION ONLY
| 25’ LONG| 50’ LONG| 100’ LONG| 150’ LONG
0 to 6 Amps| 18 AWG| 16 AWG| 16 AWG| 14 AWG
6 to 10 Amps| 18 AWG| 18 AWG| 14 AWG| 12 AWG
10 to 12 Amps| 16 AWG| 16 AWG| 14 AWG| 12 AWG
12 to 16 Amps| 14 AWG| 12 AWG| GREATER THAN 50 FEET NOT RECOMMENDED
UNPACKING AND INVENTORY
Check shipping carton and machine for damage before unpacking. Carefully remove packaging materials, parts and machine from shipping carton. Always check for and remove protective shipping materials around motors and moving parts. Lay out all parts on a clean work surface.
Remove any protective materials and coatings from all of the parts and the planer. The protective coatings can be removed by spraying WD-40 on them and wiping it off with a soft cloth. This may need to be redone several times before all of the protective coatings are removed completely.
After cleaning, apply a good quality paste wax to any unpainted surfaces including the infeed, outfeed, and center tables. Make sure to buff out the wax before assembly.
Compare the items to inventory figures and verify that all items are accounted for. If at all possible, retain shipping carton for warranty service if ever needed.
If any parts are missing, do not attempt to plug in the power cord and run the
machine. The machine should only be turned “ON” after all the parts have been
obtained and installed correctly.
For missing parts, contact CUTECH at
858-886-7333.
- A. Raise / Lower Handle
- B. Dust Port
- C. Dust Port Thumb Screw (2)
- D. Handle Screw
- E. Torx Wrench
- F. Hex Wrench
- G. Vacuum Adaptor (2” to 2-1/2” and 4”)
ASSEMBLY
WARNING! MAKE CERTAIN THAT THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE.
ATTACHING DEPTH ADJUSTMENT HANDLE
Attach the raise/lower adjustment handle (A) to the shaft (B) and fasten in
place with 1 Hex Socket Head screw. Tighten screw using supplied hex wrench.
SEE FIG 1.
ATTACHING DUST PORT and ADAPTOR
The Dust Port is to be used when the planer to be connected to a dust
collector. It has a 2” port on it to accommodate dust collection systems and
2-1/2” & 4” adaptor to connect vacuum hose.
To install:
1. Install the 2” dust port (A) in the rear of the planer by using 2 thumb
screws (B). SEE FIG 2A. If needed for 2-1/2” or 4” vacuum hose, install the
vacuum adaptor by supplied hex wrench(C). SEE FIG 2B.
SECURING PLANER TO A TABLE OR WORKBENCH
During operation, if there is any tendency for the planer to tip over, slide
or walk, the planer MUST be secured to a supporting surface such as a
workbench or table. Four holes are provided (2 are shown at (A)) to securely
mount the planer. The surface you are mounting the planer to should be
perfectly flat. SEE FIG 3.
ADJUSTMENTS
WARNING! MAKE CERTAIN THAT THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE BEFORE ANY ADJUSTMENTS ARE MADE.
LEVELING EXTENSION TABLES
The extension tables must be level with the planer table. To check the extension tables and adjust if necessary:
-
Lay a straight edge (A) on the planer table (C) with one end of the straight edge over theb infeed table (B). SEE FIG 4.
-
Check to make sure that the infeed table is level with the planer table.
-
If an adjustment is necessary, raise table, loosen lock nuts (D) and adjust Hex Head Screws (E) on each side of the table until the infeed table is level with the planer table. This will adjust the outer edge of the table. If necessary, loosen the three screws of one side of infeed table (F), after adjusting, then retighten the screws back. Adjust another side of infeed table in the same manner.
-
Recheck for level and repeat adjustment if necessary.
-
Repeat this process for leveling the outfeed table.
RAISING AND LOWERING HEAD ASSEMBLY
The head assembly consists of the cutterhead, knives, feed rollers, cutterhead guard, and the motor. Raising and lowering of the head assembly controls the depth of cut on the planer.
To adjust:
-
To raise the head assembly (A), turn the adjusting handle (B) clockwise. SEE FIG 5.
-
To lower the head assembly, turn the adjusting handle counterclockwise.
NOTE: One revolution of the handle will move the cutterhead up or down
approximately 1/16”.
You can confirm this by referencing the scale (C) on the front right side of
the planer.
REPLACING CUTTER INSERTS
WARNING! MAKE CERTAIN THAT THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE BEFORE ANY ADJUSTMENTS ARE MADE.
WARNING! Be VERY CAREFUL when handling the cutter inserts as they are EXTREMELY SHARP and can cause serious injury!!!
WARNING! NEVER GRASP THE CUTTERHEAD BY HAND!
This 12-1/2″ cutterhead is equipped with 24 indexable cutter inserts. Each cutter insert can be rotated to reveal one of its two cutting edges. Therefore, if one cutting edge becomes dull or damaged, simply rotate it 90° to reveal a fresh cutting edge.
In addition, each cutter insert has a reference mark on one corner. As the
cutter insert is rotated, the reference mark location can be used as an
indicator of which edges are used and which are new. When the reference mark
revolves back around to its starting position, the cutter should be replaced.”
WARNING! NEVER GRASP CUTTERHEAD BY HAND AS THIS WILL RESULT IN SERIOUS INJURY!
To rotate or change cutter inserts:
-
Face the rear of the machine. Remove the Dust Port and Chute. Refer back to the section labeled ATTACHING DUST PORT in the ASSEMBLY section page 13 for information on removal.
-
Use the handle to lower the cutterhead assembly down to about 1” on the scale.
-
Insert the supplied Hex wrench through the hole located on the side of the machine.
Rotate the cutterhead to a position where a cutter inserts is visible. SEE FIG. A. next page.
(You may have to raise or lower cutterhead to be able to insert the Hex wrench into the cutterhead) -
While holding the hex wrench to prevent cutterhead rotation, remove the cutter inserts screw using the provided Torx wrench allowing the tip to be removed.
-
Carefully clean all dust and dirt off the cutter tip and the cutterhead seat. Replace or rotate the cutter insert so a fresh sharp edge is facing outward. If available, use pitch remover to be sure all wood residue is off the cutterhead, cutter insert, and screws, before attempting to rotate or replace them. Using a shot of compressed air is also helpful.
Be sure to wear safety glasses when using compressed air. -
Lubricate the Torx screw threads with light machine oil and wipe the excess oil off the threads. Install cutter insert and torque the Torx screw to 48-50 inch/ pounds.
THICKNESS SCALE ADJUSTMENT
The thickness scale, located on the right of the planer, shows the thickness
of the finished workpiece. To make sure the scale is set properly, run a piece
of wood through the planer and measure the thickness of the wood. If the scale
is out of alignment, loosen the two round head screws (A) holding the scale
indicator (B) and adjust the thickness indicator to the correct setting.
Make sure to re-tighten the two screws once the adjustment is complete. FIG 6
OPERATIONS
NOTE: This operations section was designed to give instructions on the basic operations of this planer. However, it is in no way comprehensive of every planer operation. It is strongly recommended that you read books, trade magazines, or get formal training to maximize the potential of your planer while minimizing the risks.
NOTE: This planer is designed to process wood ONLY.
WARNING! Make sure the switch is in the “OFF” position before connecting cord into socket. Do not touch the plug’s prongs when unplugging or plugging.
WARNING! In the case of a power outage (such as a breaker or fuse trip), always turn the switch to the “OFF” position until the power is restored.
- The on/off switch (A) Fig. 7 is on the front of the planer motor. To turn the machine “ON”, move the switch up to the “ON” position.
- To turn the machine “OFF”, move the switch (A) down to the “OFF” position.
TURNING SWITCH IN THE “OFF” POSITION
IMPORTANT: When the machine is not in use, the switch should be on the
“OFF” position to prevent unauthorized use. To lock the machine, pull the
switch key (K) out of the switch (Fig. 8). Without the switch key, the switch
will not work. However, if the switch key be removed while running the planer,
the machine can be moved to “OFF” position, but cannot be restarted without
the switch key.
DEPTH-OF-CUT INDICATOR
The Depth-Of-Cut Indicator, located on the front of the machine, is a convenient way to quickly determine how much material is being planed off in one pass.
-
With the machine OFF, insert your workpiece just under the cut scale (A). SEE FIG 9
-
Crank the raising / lowering handle until the button (B) comes in contact with the workpiece.
As you rotate the raise / lower handle, the needle on the depth of cut scale will move showing how much material will be removed in that pass.
GETTING PREPARED
It is always a good idea to use a piece of scrap wood for your first planing attempt. Also, before each use of the planer, make it a habit of checking for loose fasteners, fittings or hardware. Turn the planer ON and allow it to reach full speed. Pay close attention to any excessively loud noises that may be coming from the planer or any excessive vibration. If either occurs, shut down the planer immediately checking again for loose hardware. Go through the ASSEMBLY and ADJUSTMENTS sections again if necessary.
BASIC OPERATION
WARNING! To avoid serious personal injury, NEVER stand directly in line with the front or rear of the planer. If an object is thrown from the planer, it will travel in this direction.
- Stand to either the left or right side of the planer.
- Turn the switch to the ON position.
- Lift the workpiece onto the infeed table by grabbing the edges of the board at the middle of the length. NOTE: For longer pieces, be sure to use additional supports or stands.
- Push slightly on the board to start feed and allow the feed rollers to pull the board through the planer. Once the feed rollers start to pull the workpiece through, let go of the board and allow the rollers to do their job. DO NOT push or pull on the workpiece once the rollers have engaged.
- Move to one side of the rear of the planer and receive the planed workpiece by grabbing the edges of the wood like you did when feeding the workpiece in.
- It normally takes several passes of varying depths to achieve a smooth finish, so repeat this process as many times as necessary. Remember the less you take off in a pass, the smoother the finish will be. Finish the surface by sanding.
THICKNESS PLANING
Thickness planing sizes the workpiece to a desired thickness, while at the
same time creating a smooth and level surface. The thickness of each cut will
depend on the type of wood, width of the workpiece, and condition of the
lumber (i.e. dryness, grain composition, straightness, etc).
Always make thin test cuts on a scrap piece of wood prior to performing final
cuts.
GENERAL TIPS AND GUIDELINES
- Thickness planing always works best when at least one side of the workpiece has a flat surface. If both sides of the workpiece are rough, feed one face of the board through the planer until the entire surface is flat.
- ALWAYS plane both sides of the workpiece to reach the desired thickness.
- DO NOT plane workpieces less than 3/16-in thick, less than 3/4-in wide, or shorter than 7-in.
- It is not recommended to continuously use the planer at its maximum depth of cut (1/16”) and at its full width (12-1/2”) as this will shorten the life of the motor.
- Light cuts create a smoother finish than heavier cuts.
- If a smooth cut is not obtained, see TROUBLESHOOTING GUIDE on page 24.
AVOIDING SNIPE
Snipe, gouging or depression of the board at the ends, can occur when the
board is not properly supported. For workpieces longer than 4 ft, greater care
must be taken to reduce the problem because the additional length of the
workpiece translates into more unsupported weight pulling down on the end of
the board. This unsupported weight will work against keeping the stock flat.
Make sure to use supports or stands whenever long pieces are being planed to
avoid this problem.
Since snipe occurs at the end of the boards, it is good practice to start with
a workpiece that is slightly longer than what you need so that you can simply
cut off the ends if necessary.
Also see TROUBLESHOOTING for further information.
MAINTENANCE
WARNING! MAKE CERTAIN THAT THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE PROCEDURES
Your planer should provide you with a long time of service provided you take the time to perform the following maintenance operations
CLEANING
Sawdust buildup and other debris can cause the tool to plane incorrectly. Periodic cleaning and waxing is needed for accurate, precision planing. Any moving parts should be cleaned regularly with a penetrating oil and lubricated with a light coating of medium weight machine oil
CAUTION! With the machine unplugged, blow off motor with low pressure air to remove dust or dirt. Air pressure above 50 P.S.I. should not be used as high-pressured air may damage insulation. The operator should always wear a respirator and eye protection when using compressed air. Do not allow chips and dust to accumulate under the machine. Keep area clean and in safe order.
Having clean feed rollers is essential for optimal results. Check feed rollers after each use for buildup of pitch, gum, or resin, and be sure to clean off with a non-flammable tar and pitch remover that is not harmful to rubberized surfaces.
Periodically clean, wax, and buff the tables. This will aid in the prevention of improper feeding of the workpiece.
HARDWARE TIGHTNESS
Periodically check all clamps, nuts, bolts, and screws, for tightness and condition. Stop the machine and recheck the cutterhead screw and knives, or tips, for tightness after about 50 hours of operation. Recheck periodically.
GEAR LUBRICATION
The gears in the gear box should be lubricated periodically.
-
Facing the front of the machine, remove the raise/ lower handle. SEE FIG. 1 page 13.
-
Remove the 4 screws on the upper sides for holding the top cover on the machine. Remove the top cover.
-
On the left side panel, remove the 3 socket head screws (A) located around the bottom edge and remove the side panel to expose the gearbox cover. SEE FIG 10.
-
Place a light coat of multi-purpose grease on the teeth of the gears (A) and a light coat of spray lubricant on the chain (B). Do not over-lubricate and replace the side panel. SEE FIG 11.
-
Replace all covers, panels and guards, that you removed once lubrication is complete.
BRUSH REPLACEMENT
Brush life will vary depending on the load placed on the motor. The brushes should be inspected every 10-15 hours of use. To inspect or replace:
-
Remove the brush holders, one of which is shown at (A). The other is located in the same position on the rear of the motor assembly. The Brush Holder can be removed using a flat blade screwdriver. SEE FIG. 12.
-
Once the brush has been removed, inspect the carbon (B), the spring (C), and the wire (D). SEE FIG 13.
-
If the carbon of either brush is worn down to 3/16” or less, both brushes should be replaced.
Also if the spring or wire are burned or damaged in any way, both brushes should be replaced.
TROUBLESHOOTING GUIDE
Motor and Machine Operation
| PROBLEM | LIKELY CAUSE | SOLUTION |
|---|---|---|
| Snipe (depressions at end of workpiece) | Dull cutter inserts |
Infeed or outfeed tables out of adjustment.
Residue on rollers.| Replace or turn cutter inserts. Readjust tables. Feed
scrap of same thickness before and after workpiece.
Clean rollers.
Torn grain.| Too deep or shallow blade setting.
Work piece being fed against grain.
Dull cutter inserts| Reduce or increase the depth of cut. Feed other end of
board first.
Replace or turn cutter inserts. Try skewing board when feeding.
VERY slightly dampen work piece.
Fuzzy/rough grain.| High wood moisture content. Dull cutter inserts Too deep
cut.| Dry wood before planing. Replace or turn cutter inserts Reduce depth of
cut
Board thickness does not match depth scale indicator.| Depth scale incorrectly
set.| Adjust depth scale.
Will not start.| Not plugged in. Blown circuit.
Switch key removed.| Check the power source.
Replace fuse, reset breaker, or call electrician.
Replace switch key.
Interrupted operation| Unit overloaded. Circuit overloaded.| Reduce load.
Operate on circuit separate from other appliances or motors or connect to
circuit with adequate amp rating.
Planer not feeding properly| Too much material being removed.
Cutter inserts dull.
Build up on tables.
Build up on rollers.| Reduce cut depth.
Replace cutter inserts.
Clean tables and apply paste wax.
Clean rollers with a cleaner safe for rubber surfaces.
PARTS
Item NO.| ****
DESCRIPTION
| ****
Size
| ****
QTY
---|---|---|---
1| TORX WRENCH| | 1
2| HEX WRENCH| | 1
3| HEX SOC HD CAP SCR| M6xP1.0x8L| 15
4| HANDLE ASSEMBLY| 4a~4f| 1
5| TOP COVER| | 1
6| LEFT SIDE PANEL| | 1
7| SCREW| M5XP0.8X12L| 6
8| WASHER| Ø5xØ12x1T| 2
9| AIR DEFLECTOR| | 1
10| LEAD SCREW BUSHING| | 3
11| BEARING RETAINER| | 1
12| RIGHT SIDE PANEL| | 1
13| SPINDLE BEARINGS| 6000ZZ Ø26xØ10| 5
14| HANDLE BAR| | 2
15| C-RING| | 3
16| CHAIN| | 2
17| SPROCKET| | 4
18| SPACER| | 1
19| SCREW| M5xP0.8x35L| 4
24| ELEVATION NUT| | 8
31| GEAR BOX COVER| | 1
32| GEAR BOX COVER| | 1
33| PINION GEAR| | 1
34| BEARING| 6203ZZ
Ø40xØ17x12T
| 2
35| BASE BEARING RETAINER| | 4
36| CORD CLAMP| | 1
37| PLATE| | 2
38| SPINDLE SPROCKET| | 4
39| SCREW| M5X0.8X8| 2
40| STAR WASHER| Ø10xØ5.5| 2
41| SCREW| M5xP0.8x12L| 8
42| FLAT WASHER| Ø10.3xØ18x1T| 4
43| WASHER| Ø12.2xØ25.8| 4
44| MOTOR PIVOT ROD| | 1
45| UPPER FRAME| | 1
46| BELT GUARD| | 1
47| WASHER| Ø18xØ8x2T| 2
48| SCREW| M5X0.8X12| 21
49| MOTOR BRACKET| | 1
51| SCREW| M8X1.25X16L| 1
52| HEIGHT ADJ SPINDLE| | 1
53| SPINDLE| | 3
54| SPACER| | 1
55| KEY| | 1
57| SCREW| M5xP0.8x5L| 1
58| TAP SCR| M4.5xP1.6x8L| 8
59| DUST CHUTE| | 1
60| BEARING CAP| | 1
61| DUST PORT| | 1
62| CUTTERHEAD PULLEY| | 1
63| BELT| 135J6| 1
64| HEX NUT| M16X22T| 1
65| MOTOR PULLEY| | 1
66| IDLE WHEEL| | 2
67| IDLE WHEEL SHAFT| | 2
68| HEX SOC HD SCR| M5xP0.8x25L| 2
69| SPRING| Ø2.0xØ17x30L| 2
70| THUMB SCREW| | 2
73| INFEED ROLLER| | 1
76| SPRING| Ø2.0xØ15.5x30L| 2
77| OUTFEED ROLLER| | 1
78| MOTOR* (150~184)| | 1
79| BASE| | 1
80| FLAT WASHER| Ø4.2xØ15x2T| 4
81| NYLOCK HEX SOC HD SCR| M4xP0.7x12L| 4
82| CURSOR| | 1
83| PAN HD SCR| M3xP0.5x20L| 2
84| SCREW| M4xP0.7x10L| 2
85| WASHER| Ø19.95xØ28×0.5T| 4
86| FLAT WASHER| Ø20xØ27×1.5T| 4
87| HEX SOC HD SCR| M5xP0.8x20L| 1
88| GEAR BOX ASSEMBLY| | 1
89| SCREW| M5xP0.8x6L,SCM3| 8
112| BASE GUIDE RAIL| | 2
113| PAN HD SCR W/WASH| M4xP0.7x6L| 12
114| TABLE SUPPORT| 4T,STK| 4
115| SPRING WASHER| | 4
116| TABLE BUSHING| | 4
117| PAN HD SCR| M6xP1.0x16L| 4
118| EXTENSION TABLE| | 2
119| SPIRAL CUTTERHEAD| | 1
120| CUTTER INSERTS| | 24
121| TORX SCREW| M5xP0.8×15.6L| 24
126| SCALE| | 1
141| SCREW| M6x5T| 5
142| SCREW| M6x20L| 5
226| CHAIN| | 1
230| THUMB SCREW| | 2
235| VAC ADAPTER| | 1
236| NUT HEX| M5xP0.8| 1
237| NYLOCK SCR HEX SOC HD| M5xP0.8x25L| 1
238| WEAR PLATE| | 1
239| BEARING| | 4
240| BEARING BLOCK| | 2
241| BEARING BLOCK| | 2
242| INDICATOR DEPTH ASSY| | 1
243| PAN HD SCR| M4xP0.7x12L| 3
244| SPECIAL NUT| | 1
245| POINTER HOUSING| | 1
246| COIL SPRING| | 1
247| ROD POINTER ELEVATING| | 1
248| POINTER| | 1
249| BUSHING| | 1
250| NYLOCK SCR PAN W/WASHER| M4xP0.7x10L| 1
251| POINTER HOUSING| | 1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>