CBG 1001524 30 RTS 24V DC Motor User Guide
- June 3, 2024
- CBG
Table of Contents
CBG 1001524 30 RTS 24V DC Motor User Guide
SAFETY
- Before installation, check that this product is compatible with the associated equipments and accessories.
- Moreover, the installer must comply with current standards and legislation in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for the product.
IMPORTANT: Upper and lower limits are set at the factory. In the event limit setting is required, please follow steps under INITIAL PROGRAMMING AND LIMIT SETTING.
TO FINISH PROGRAMMING:
- Supply power to the motor (see example under WIRING). The LED on the motor will flash Orange twice (repeating every 10 seconds)
- Choose the transmitter you wish to control the shade and choose the appropriate channel for control.
- PRESS & HOLD the UP and DOWN buttons on the transmitter until the shade jogs once.
- BRIEFLY PRESS the PROGRAMMING BUTTON on the transmitter to pair the control to the motor. The motor will jog once.
The LED on the motor will flash Green 5 times then stop flashing.
The control is now paired to the motor.
WIRING
Connect the power cable to the motor.
INITIAL PROGRAMMING AND LIMIT SETTING
NOTE: Motor will exit programming mode after 2 minutes of inactivity.
Prior to confirming limits, the shade only operates when the UP or DOWN
buttons are continuously pressed. Releasing the buttons stops the shade.
Step 1 : Supply power to motor.
Step 2 : To initiate programming PRESS & HOLD both the UP and DOWN buttons at the same time until the shade jogs.
Step 3 : Check the direction of operation. Press the DOWN button and confirm the shade lowers.
if the shade raises instead of lowering, change the direction – PRESS & HOLD the MY/STOP button until the shade jogs. Confirm correct direction of operation before proceeding.
Step 4: Bring the shade to your desired upper limit. PRESS & HOLD both the MY/ STOP and DOWN buttons until the shade begins to move down, then release. Stop the shade at the desired lower limit, adjust by pressing the UP or DOWN buttons.
Step 5 : PRESS & HOLD the UP and MY/STOP buttons until the shade begins to move up. The shade will stop at the original upper limit.
Step 6 : PRESS &
HOLD the MY/STOP button until the shade jogs to confirm both limit settings.
Step 7 : To finalize BRIEFLY PRESS the PROG button on the back of the remote. The shade will jog and will now operate in user mode. A brief press of the UP or DOWN button will send the shade to the respective limit.
ADJUSTING THE LIMITS IN USER MODE
step 1 : Move the shade to the current limit position you wish to adjust and let it stop.
Step 2 : PRESS & HOLD both UP and DOWN buttons simultaneously until the shade jogs, then release.
Step 3 : Adjust to a new limit position using the UP or DOWN buttons.
Step 4: PRESS & HOLD the MZ / STOP button until the shade jogs, then release. Check the new limit.
ADJUSTING THE SPEED
LED blinks alternately in green and yellow during the adjustment.
-
Move the shade away from the end limits. PRESS & HOLD the UP, MY/STOP and DOWN buttons simultaneously, until the shade jogs. The shade will move up and down automatically in 10 second cycles.
-
To increase the speed, PRESS & HOLD the UP button until the shade jogs. Repeat as needed.
Maximum speed is achieved when the shade jogs 3 times in each direction when the UP button is pressed.
-
To decrease the speed, PRESS & HOLD the DOWN button until the shade jogs. Repeat as needed.
Minimum speed is achieved when the shade jogs 3 times in each direction when the DOWN button is pressed. -
To confirm the new speed, PRESS & HOLD the MY/STOP button until the shade jogs.
RESETTING THE MOTOR TO FACTORY MODE
PRESS & HOLD the PROG button on the motor (shown below) for
approximately 12 seconds during which the shade will jog 3 separate times.
All programmed remotes and limit settings will be erased. Motor is now reset to factory mode. Motor limits will need to be re-established.
SETTING FAVORITE “MY” POSITION
-
Move the shade to the desired position and press MY/STOP button to stop the shade.
-
PRESS & HOLD the MY/STOP button until the shade jogs. The “my” favorite position is set.
-
To set a NEW “my” position, repeat steps 1 and 2.
TO DELETE: First send the shade to the current “my” position, then PRESS & HOLD the MY/STOP button for 5 seconds. The shade will jog to confirm deletion.
USING THE FAVORITE “MY” POSITION
While the shade is stationary, a simple PRESS of the MY/STOP button will move the shade to the “my” position from any shade position.
If the shade is in motion, first stop it by pressing MY/STOP and then PRESS MY/STOP again to send it to the “my” favorite position.
TIPS AND RECOMMENDATIONS
To delete all the transmitters programed, PRESS and HOLD the PROG
button on the motor (as shown) until the shade jogs twice. All the
transmitters are deleted.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>