beko BHCI31322BBH Cooker Hood User Manual

June 15, 2024
Beko

beko Logo Cooker Hood
User Manual

BHCI31322BBH Cooker Hood

beko BHCI31322BBH Cooker Hood BHCI 31322 BBH

Please read this user manual first!
Dear Valued Customer,
Thank you for preferring this Beko appliance. We hope that you get the best results from your appliance which has been manufactured with high quality and state-of-the-art technology. For this reason, please read this entire user manual and all other  ccompanying documents carefully before using the appliance and keep it as a reference for future use. If you handover the appliance to someone else, give the user manual as well.
Follow the instructions by paying attention to all the information and warnings in the user manual.
Remember that this user manual  may also apply to other models.Differences between models are explicitly described in the manual.
Meanings of the Symbols
Following symbols are used in various sections of this user manual:

**** Important information and useful hints about usage.
WARNING: Warnings against dangerous situations concerning the security

of life and property.
| WARNING: Warning for danger of fire.
| WARNING: Warning for electric shock.
Icon| Protection class for electric shock.

RECYC LED & RECYCLABLEPAPER

Important safety and environmental instructions

1.1 General Safety
Important SafetyInstructions Read CarefullyAnd Keep For FutureReference This sectioncontains safety instructions that will help protectfrom risk of fire, electricshock, exposure to leak microwave energy, personalinjury or property damage.Failure to follow these instructions shall void anywarranty.

  • Beko products complywith the applicable safetystandards; therefore, incase of any damage onthe appliance or powercable, it should be repaired or replaced by thedealer, service center or aspecialist and authorizedservice alike to avoid anydanger. Faulty or unqualified repair work may bedangerous and cause riskto the user.

  • This appliance is intendedto be used in household and similar applications such as:
    – Staff kitchen areas in shops, offices and other working environments;
    – Farm houses
    – By clients in hotels, and other residential type environments;
    – Bed and Breakfast type environments.

  • Operate the appliance for its intended purpose only as described in this manual.

  • The manufacturer cannot be held liable for damages resulting from improper installation or misuse of the product.

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowl- edge if they have been given supervision or in struction concerning use of the appliance in a safeway and understand thehazards involved.

  • Children shall not be allowed play with the appliance. Cleaning and usermaintenance shall not bemade by children withoutsupervision.

  • The minimum distancebetween the supportingsurface for the cookingvessels on the hob andthe lowest part of yourproduct must be at least 65 cm.

  • If the instructions for installation for the gas hobspecify a greater distance,this has to be taken into account.

  • Make sure that your mainspower supply complies with the information supplied on the rating plate ofthe appliance.

  • Never use the appliance ifthe power cable or the appliance itself is damaged.

  • Prevent damage to the power cable by not squeezing, bending, or rubbing it on sharp edges. Keep the power cable away from hot surfaces and naked flame.

  • Use the appliance with a grounded outlet only.
    WARNING: Do not connect the appliance to the mains until the installation is fully complete.

  • Place the appliance in a way so that the plug is always accessible.

  • Do not touch the lamps if they have operated for a long time. They can burn your hands since they will be hot.

  • Follow the regulations set out by competent authorities on discharge of the exhaust air (this warning is not applicable for use without flue).

  • Operate your appliance after putting a pot, pan etc. on the hob. Otherwise, high heat may cause deformation in some parts of your product.

  • Turn off the hob before taking the pot, pan etc. from it.

  • Do not leave hot on the hob. Pans with hot may cause self combustion.

  • Pay attention to your curtains and covers since may catch fire while cooking food such as fries.

  • Grease filter must be cleaned at least monthly. Carbon filter must be replaced at least every 3 months.

  • Product shall be cleaned accordance with user manual. If cleaning was not carried out in accordance with user manual, there may be fire risk.

  • Do not use non-fire-resistant filtering materials instead of the current filter.

  • Only use the original parts or parts recommended by the manufacturer.

  • Do not operate the product without the filter and do not remove the filters while the product is running.

  • In the event of be started any flame, de-energize your product and cooking appliances.

  • In the event of be started any flame, cover the flame and never use water to extinguish.

  • Unplug the appliance before each cleaning and when the appliance is not in use.

  • The negative pressure in the environment should not exceed 4 Pa (4×10 bar) while the hood for electric hob and appliances running on another type of energy but electricity operate simultaneously.

  • In the environment where the appliance is being used, the exhaust of devices running on fuel orgas, such as room heatermust be absolutely isolated or device must behermetical type.

  • When connecting the flueuse pipes with a diameteof 120 or 150 mm. Pipeconnection must be ashort as possible and havas few elbows as possible

  • Danger of choking! Keeall the packaging materials away from children.
    CAUTION: Accessible parts may become hot when used with cooking appliances.

  • The product outlet mustnot be connected to airchannels that includother smoke.

  • The ventilation in the roommay be insufficient whethe hood for electric hobis used simultaneouslywith the devices operatingon gas or other fuels (this may not apply to appli ances that only discharge the air back into the room).

  • Objects placed on the product may fall. Do not place any objects on the product.

  • Do not flambe under the your product.
    WARNING: Before installing the Hood, remove the protective films.

  • Never leave high naked flames under the hood when it is in operation

  • Deep fat fryers must be continuously monitored during use: overheated can burst into flames.

1.2 Compliance with the WEEE Directive and Disposing of the Waste Product:
** This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).
This symbol indicates that this product shall not be disposed with other household wastes at the end of its service life.
Used device must be returned to offical collection point for recycling of electrical and electronic devices. To find these  collection systems please contact to your local authorities or retailer where the product was puchased. Each household performs important role in recovering and recycling of old appliance.
Appropriate disposal of used appliance helps prevent potential negative consequences for the environment and human health.
1.3 Compliance with RoHS Directive
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.
1.4 Package Information
**
Packaging materials of the product are manufactured from  recyclable materialsin accordance with our National  Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

General appearance

2.1 Overview

  1. Body
  2. Control panel
  3. Grease filter
  4. Lighting

beko BHCI31322BBH Cooker Hood - Technical 2.2 Technical data

Model BHCI 31322 BBH
Supply voltage & frequency 220-240V ~ 50 Hz
Lamp power 2 x 3 W
Motor power 115 W
Air flow – 3. Level 300 m³/h
Motor Insulation Class Class F
Insulation class Class II

Using the appliance

3.1 Controls panel


A : Light on/off| Pressing the “a “ button turns on the light. Pressing the button again switches off the lighting.
B : 1. Speed button| Pressing the “1” button activates the hood turbine at minimum speed
C : 2. Speed button| Pressing the “2” button activates the hood turbine at medium speed
D : 3. Speed button| Pressing the “3” button activates the hood turbine at maximum speed
E : 0. Hood shut off| Pressing the “0” button deactivates the hood turbine

  • The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
  • Never use the hood for purposes other than for which it has been designed.
  • Never leave high naked flames under the hood when it is in operation.
  • Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
  • Deep fat fryers must be continuously monitored during use: overheated can burst into flames.

3.2 Efficient use in terms of energy saving

  • When using your appliance, adjust the speed settings according to vapour and odour intensity, in order to save energy.
  • Use low speeds (1-2) under normal conditions, and high speed (3) and boost mode for intense odour and vapour.
  • The hood is equipped with lamps in order to illuminate the cooking area.
  • Using them for environmental lighting shall cause unnecessary energy expenditure and insufficient lighting.
  • For your device to consume less energy, run it at a low speed level.
  • Your device will reduce energy consumption as it will run more efficiently when you provide sufficient air intake to it.
  • Set your device to the intense suction power level before the formation of steam, in cases where you know that the dense steam will occur. So, you reduce energy consumption by using your device for a shorter time as it will have a sufficient air intake.
  • Keep the lids of the cookware closed to reduce the steam evolving.

3.3 Operating the hood

  • Hood is equipped with a motor having various speed settings.
  • For a better performance, we advise you to use low speeds in normal conditions, and high speeds when smell and vapors are intensified.
  • You can start the hood by pressing the desired speed level key.(B, C, D)
  • You can illuminate the cooking area by pressing the light key. (A)

3.4 Lamp replacement

beko BHCI31322BBH Cooker Hood - replacement

Lamp|
---|---
Bulb power| 3 W
Holder/Socket| GU10
Bulb voltage| 230 V
Size| 53×50 mm
ILCOS Code| DR/F-3-230-GU10-50
Luminous flux| 255 lm
Correlated colour temperature| 3000 K

This product contains a light source of energy efficiency class “A”.

  • Before replacing the light bulbs, disconnect the power supply of the hood.
  • Do not touch the light bulbs when they are hot.
  • Be careful not to touch the replaced light bulb directly with hands.

** You may procure lamps from Authorised Service Agents.
3.5 Operation with flue connection**

  • Vapour is extracted through the flue duct, which is fastened to the connection head on the hood.
  • The diameter of the flue duct must be the same as the connection ring. In horizontal settings, the pipe has to have a slight upward slope (around 10º) so that the air can exit the room easily.

3.6 Operation without flue connection

  • Air is filtered through the carbon filter and recirculated in the room. Carbon filter is used when it is impossible to use a flue in the house.
  • In flueless use, remove the flaps inside the flue adapter.
  • Remove the oil filter. To install the carbon filter, fit the filter to the tabs by centring it on the plastic piece on both sides of the fan body. Tighten it by turning right or left.
  • Replace aluminium oil filter.

Cleaning and maintenance

The device should be cleaned and maintained regularly. Failure to keep the device clean will adversely affect the service life of the device. For cleaning and maintenance, follow the instructions stated in the manual.
**Before cleaning and maintenance, unplug the product or turn off the switch.
Non-compliance with the provisions associated with the cleaning of the  device and replacement of the filters may result in a risk of fire. Therefore, it is recommended to follow the guidelines stated here. The manufacturer is not responsible for the engine  damages or fires originating from the improper use.
Clean using only a cloth dampened with a neutral liquid detergent. Do not use abrasive products or alcohol.
4.1 Cleaning of grease filter**
This filter captures particles in the airFirst remove the grease filters for this process. Wash the filters with liquid detergent and rinse them with water and install them back after they get dryGrease filters may get discolered as they are washed; this is normal and you don’t need to change your filter.beko BHCI31322BBH Cooker Hood - filter

  • The filter is removed by moving the locks in the direction indicated by the arrows.
  • Tilt the metal grease filter forward and take it out. Wash and rinse the oil filters in liquid detergent water and reinsert the oil filter into its socket by reversing the above steps.

** You can wash the grease filter in the dishwasher.
CAUTION: In case of normal use, clean your filter once in a month.
4.2 Changing of carbon filter
The hood can be fitted with an active carbon filter.
The carbon filter is applied only  in case the hood isnot connected to the vent duct.
beko BHCI31322BBH Cooker Hood - connectedWARNING:**

  • The carbon filter is neverwashed.
  • Replace carbon filters once every 3 months.
  • Carbon filter is available from Authorized Services.

Installation of appliance

WARNING: Before starting the installation, read the safety information on user manual.
WARNING: Failure to install with screws and stabilizers in accordance with these instructions may result in electric shock.
For the installation of the hood, please contact the nearest Authorized Service.
It is the customer’s responsibility to prepare the location and electrical installation of the hood.
5.1 Position of the appliance

beko BHCI31322BBH Cooker Hood - appliance 1

  • Distance between the cooker and the cooker hood must be considered priorto assembly. This distance should be 65 cm.
  • Distance must be measured from thesurface of grate for gas cookers, fromsurface of glass for electric cookers.

5.2 Installation accessories

  1. beko BHCI31322BBH Cooker Hood - channels 2 Product
  2. User manual
  3.  Ø120mm flue flap
  4. 4x Ø8X70 steel screw dowel

5.3 Hood installation
Before installing the hood, make sure that the component to which the hood is to be attached can carry sufficient load. The hood should be mounted directly to the ceiling or to a load-bearing construction which is sufficiently strong. It is forbidden to mount the hood to flimsy elements such as plasterboards. The hood is equipped with fixing pins for concrete. During installation, the generally applicable regulations for the discharge of air from rooms must be observed.
Before proceeding with the installation:

  • Check that the dimensions of the purchased product are appropriate for the chosen destination.
  • Disconnect and remove (if possible) furniture located in the hood installation area to gain easy access to the ceiling or wall on which the hood is to be mounted. If this is not possible, components in the vicinity of the work to be carried out must be secured.
  • Check that there are outgoing cables for the hood connection near the hood installation area.
  • Check that there are no installation cables (electrical, hydraulic, etc.) in the areas to be drilled.
  • Equip yourself with the following tools: tape measure, pencil, drill, Ø10 drill bit, screwdriver.

5.4 Installation steps

  1. Remove the aluminium filter and disconnect the turbine plug.beko BHCI31322BBH Cooker Hood - turbine
  2. Unscrew the six M4x12 bolts that connect the base body to the mounting channels and remove the body from the rest of the hood.beko BHCI31322BBH Cooker Hood - Removing
  3. Unscrew the mounting channels, which are fastened with M4x12 bolts, remove and set aside.beko BHCI31322BBH Cooker Hood - fastened
  4. Unscrew the six M4x12 bolts and carefully separate the turbine insert with the turbine from the upper body.beko BHCI31322BBH Cooker Hood - upper
  5. Loosen the M4x12 bolts and remove the ceiling bracket from the upper body.beko BHCI31322BBH Cooker Hood - ceiling
  6. Mount the hood according to the drawings.beko BHCI31322BBH Cooker Hood - Mountingbeko BHCI31322BBH Cooker Hood - dimensions

Mounting the hood to the ceiling. Mounting the lower body.beko BHCI31322BBH
Cooker Hood - Mounting 1Fit the pipe to the bracket by aligning it with the mounting holes. The ventilation grilles must be located on the sides.
After adjusting the holes, screw the pipe in place using M4x12 bolts Mounting the hood to the ceiling. Mounting the turbine to an outlet pipe.beko
BHCI31322BBH Cooker Hood - lettersThe turbine outlet axis coincides with the discharge pipe axis (assuming that the steps in Fig. 10 have been performed correctly). When assembling the turbine insert, care must be taken to match the turbine outlet with the discharge pipe. Then screw in the insert with the turbine using 6x M4x12 bolts, positioning it with the LETTERS F marked in the two components of the hood.
Mounting the hood to the ceiling. Mounting the turbine to a flexible pipe
Important note! Pass the cable through the glands before screwing on the insert.beko BHCI31322BBH Cooker Hood - screwingWhen installing the turbine insert, first lengthen the spiro tube and connect it to the turbine outlet via a tie. Then screw in the insert with the turbine using 6x M4x12 bolts, positioning it with the letters F marked in the two components of the hood. Mounting the hood to the ceiling. Mounting the brackets.
Use 6 pcs. of M4x12 bolts to fix the mounting channels and at the same time set the required height of hood H. The brackets can be adjusted in 40 mm intervals.beko BHCI31322BBH Cooker Hood - channelsMounting the hood to the ceiling. Mounting the lower body.beko BHCI31322BBH Cooker
Hood - channels 1Slide the lower body onto the mounting channels as shown in Photo 2.
Mount the lower body to the channels with 6x M4x12 bolts
Slide the lower body gently over the upper body.
Pay special attention to the wires (so as not to damage the insulation during installation).
Mounting the hood to the ceiling. Connection of turbine, power supply, mounting of aluminium filter.beko BHCI31322BBH Cooker Hood -
aluminium 5.5 Turbine flaps
NOTE! The flaps should remain in place only when the hood is in extraction mode, i.e. when it is connected to the ventilation.

beko BHCI31322BBH Cooker Hood - Turbine 1

5.6 Storage

  • If you do not intend to use the appliance for a long time, please store it carefully.
  • Please make sure that the appliance is unplugged, cooled down and totally dry.
  • Store the appliance in a cool and dry place.
  • Keep the appliance out of the reach of children

5.7 Handling and transportation

  • During handling and transportation, carry the appliance in its original packaging. The packaging of the appliance protects it against physical damages.
  • Do not place heavy loads on the appliance or the packaging. The appliance may be damaged.
  • Dropping the appliance will render it non-operational or cause permanent damage.

Troubleshooting

Troubleshooting Reason Help
The product does not work. Check your fuse. Your fuse might be closed, make

it work.
The product does not work.| Check the electrical con- nection.| The mains voltage should be between 220-240 V
The product does not work.| Check the electrical con- nection.| Check if the other products in your kitchen are working or not.
The lighting lamp does not work.| Check the electrical con- nection.| The mains voltage should be between 220-240 V
The lighting lamp does not work.| Check the lamp switch.| The lamp switch should be in the “on” position.
The lighting lamp does not work.| Check the lamps.| The lamps of the product should not be faulty.
The air intake of the product is poor.| Check the aluminum filter.| The aluminum filter should be
cleaned at least once a month under normal conditions.
The air intake of the product is poor.| Check the air vent flue.| The air vent flue should be in the “on° position.
The air intake of the product is poor.| Check the carbon filter.| For products with carbon filters, the filter should normally be changed every 3 months.

Arçelik A.Ş.
Karaağaç Caddesi No: 2-6, 34445,
Sütlüce, İstanbul, Türkiye
www.beko.com

Documents / Resources

| beko BHCI31322BBH Cooker Hood [pdf] User Manual
BHCI31322BBH Cooker Hood, BHCI31322BBH, Cooker Hood, Hood
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals