LIVINOX LCO-SB8-70 Built in Combi Oven Instruction Manual

LIVINOX LCO-SB8-70 Built in Combi Oven

Product Introduction

Product main parameters

Safety

1. Please read all instructions carefully before using this product, in order to avoid property damage and personal injury due to improper use.
2. This product must be installed and repaired by the manufacturer’s authorized after-sales personnel only; if consumers entrust personnel not designated by the manufacturer, or if consumers perform the above operations on their own, there may be a risk of personal injury or property loss.
3. If the provisions of this manual conflict with the mandatory provisions of the law, the legal provisions shall prevail.

DANGER

1. This product will generate heat when in use, DO NOT touch the heating elements inside the steam oven cavity. When retrieving food containers from the steam oven, users should wear heat-resistant gloves or oven mittens to avoid getting burnt.
2. Keep children away from the product when it is in use, as accessible parts may become hot to the touch.
3. Disconnect the product from the power source before cleaning, maintenance, and installation to avoid electric shock.
4. To avoid fire hazards, DO NOT use this product to store items.
5. DO NOT place this product near gas pipes. Gas pipes installed in the surrounding vicinity of this product must have sufficient safety insulation (such as metal gag pipe sleeves) to ensure the gas pipes will not be affected by the high temperature emitted by this product.

WARNING

1. DO NOT place objects near the heat vent of this product in order to avoid accidents.
2. DO NOT let persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge use this product without supervision;
3. DO NOT place this product where young children can reach, in order to avoid burns, electric shock, or other accidents; when the product is operated in combination mode, the steam oven will become very hot, and children must not be allowed to use it without adult supervision.
4. DO NOT directly heat food or liquid in a sealed container to avoid explosion. When a product is in use, and after cooking when the oven door is still hot, DO NOT pour water on the oven door as it may cause the glass to break.
5. Use a separate power outlet for this product; sharing the outlet with other appliances may lead to overheating and fire hazards.
6. If the product malfunctions during usage, stop using the product immediately and proceed to the “ TROUBLE SHOOTING” section.
7. When operating in modes with steam, DO NOT stand near the heat vent; when opening the steam oven door, be cautious of hot steam in order to avoid burns.
8. Power connection to this product must be equipped with an air switch or leakage protection switch that meets the electrical parameters marked on the product nameplate before it can be connected and used.
9. DO NOT put heavy objects on top of the power cord to avoid accidents.
10. Please keep the product and power cord away from heat-generating objects, and flammable and explosive materials, to avoid product damage or fire or explosion hazards.
11. If the power cord is damaged, in order to avoid danger, it must be replaced by professionals from the manufacturer’s maintenance department or similarly qualified technicians.
12. Please use suitable steaming trays and containers to avoid spilling oil droplets and causing a fire.
13. Please place the cooking container on the shelf correctly, DO NOT place it directly on the bottom of the oven cavity to avoid accidents.
14. The steam oven door surface will become hot during or after usage, be careful to avoid getting burnt.
15. After cooking, the temperature around the steam oven cavity is still hot, please wait for the cavity to cool down before cleaning to avoid getting burnt.
16. Please keep children away from the appliance at all times.
17. This appliance can be used by children aged from years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved
18. Cleaning and user maintenance shall not be done by children without supervision.
19. Children less than years of age shall be kept away from the appliances at all times.

ATTENTION

1. Do not use the oven handle to hand heavy objects or place any objects on top of the door, or lean against or sit on the product door to avoid damaging the products.
2. Please do not touch the product or plug/unplug the power plug with wet hands, or when feet are wet or barefooted to avoid electric shock.
3. DO NOT use harsh abrasive cleaners or sharp metal scrapers to clean the steam oven door glass, as it may scratch the surface and the glass may be break.
4. This product must be placed on a sturdy and level surface. DO NOT install the product under plastic lighting equipment or plastic rack to avoid deformation or explosion hazard.
5. Handle the product with care, and lift from the bottom of the product when transporting and placing it; DO NOT use the oven door handle as a supporting point for transport to avoid damage due to excessive force.
6. DO NOT use steam cleaner to clean this product.
7. To prevent possible hazards, the control panel of the product can only be connected to the specified heating element.
8. This product can only use the temperature sensor probe recommended for this product.

Accessories List

Installation Instruction

INSTALLATION REQUIREMENTS

1. In order to ensure that the product can be used safely for a long time, the product must be installed on a perfectly sturdy surface, and the electronic components must be isolated to prevent the possibility of contact with metal accessories.
2. The kitchen cabinet where the product is installed and all adhesives used must be able to withstand a temperature of not less than °C to avoid deformation and paint cracking.
3. Before connecting to the power source, make sure :
   • According to regulations, there should be an earth system. The socket and circuit connected to the power supply must be reliably grounded.
   • After installation, the control buttons are easily accessible and operable.
   • After the product is connected to the power source, please check whether the power cord is in contact with heat-prone accessories. If there is contact, move it away to a safe distance.
   • Do not use reducers, shunts, and adapters that can cause overheating or self-ignition.
   • The manufacturer is not responsible for any direct or indirect losses caused by incorrect installation or connection of any electronic components. Therefore, all installation and connection operations must be performed by qualified technicians following local regulations.
   • DO NOT connect the ground wire to gas pipes, water pipes, lightning rods, and telephone lines to avoid accidents caused by electric shock due to poor grounding. The socket should not be installed in a place exposed to moisture, water or near a heat source.
4. When installing electrical appliances, be sure to wait until the installation is complete before turning on the power source.

Caution
This product is equipped with a 1.2m long power cord. Users are required to use a 16A socket, and this socket must be connected to a leakage protection switch. If the power cord is damaged, it must be replaced by professional maintenance personnel to avoid danger.

INSTALLATION PROCEDURE

1. Open the oven door and use the self-tapping screws to fix the product onto the kitchen cabinet (there are self-tapping screw holes on both sides of the front panel of the product). Make sure that the product is firmly fixed, so that the product will not slant forward and damage the contents in the oven during use.
2. Please refer to the diagram below when installing the product.

PRODUCT DIMENSIONS

Usage

BEFORE INITIAL USE：

1. Remove the special film covering the door glass;
2. Thoroughly clean the interior of the product (use a moist cloth to wipe the product’s exterior);
3. Fill the water tank with water, and run the product in Steam Mode at 100°C for 45 minutes, (or above) to remove the new product smell.

Control Panel

Control Key

Control Key

Normal Operation Steps

• Activate the product → select the cooking mode → set the temperature/time → Start cooking → put the dish in after preheating process → end cooking

Step 1: Activate the product

• Connect the power.
• Press to enter into Standby Mode after powering on， the display shows 888℃, 88:88Min

Step 2: Choosing the cooking mode

• Press Steam / Grill / grill&steam / Air fryer/ Recipes/ Separate control to select cooking mode;
• If using the steam or combined function, please add water into the water tank to the MAX level.

Suggest:

1. For health, please use pure water, and pour out water after cooking.
2. Note: Every mode has the default time and temp, if no need to adjust them, can proceed directly to Step 4

Step 3: Set temperature/time

1. After selecting your desired cooking functions, press to adjust temperature and time；
2. The temperature display on the screen will flash, then press or button to set the temperature you want；
3. After setting the temperature, press again and the time display on the screen will flash, then press or button to set the time you want.
   • Note: Short press to increase or decrease by 1, long press to increase or decrease by 2

Step 4: Start Cooking

Press to start cooking and the oven will enter into preheat mode, the icon on display light on. The oven will buzz for 1 minute once preheat is done and will flash; if there is no other setting for 1 minute, the oven will start cooking, and the icon will light on

• If you wish to pause the cooking, press to pause; a beep sound can be heard and the temperature and time display will flash once you pause the cooking; press again to cook continually. When oven cooking is paused, you can press to reset the cooking time or temperature; once you are done setting, just press again to restart cooking with new time and temperature.
• If you wish to cancel the cooking, press and hold for seconds will do.

Step 5: The End

• When cooking is done, the oven will buzz 5 times, “END” will display on the screen and the oven will back to standby mode; press to turn it off.
• Operation of Delay Start

Step 1: Activate the product

• Connect the power.
• Press to enter into Standby Mode after powering on， display shows 888℃, 88:88 Min.

Step 2: Select cooking mode and set the delay start time

• ➀ Press and hold for 3s to enter into the preset mode, the icon on display will flash;
• ➁~➂ Press  button to set the desired time you want, and press to confirm；
• ➃~➆ Select the cooking mode, setting the temperature and time the press the oven to start cooking.

Step 3: The End

• When cooking is done, the oven will buzz 5 times, “END” will display on the screen and the oven will back to standby mode; press to turn it off.

Operation of Smart Recipes

Step 1: Activate the product

• Connect the power.
• Press to enter into Standby Mode after powering on， display shows 888℃, 88:88 Min.

Step 2: Select the recipe code

1. Press the Smart Recipes button, buttons flash, after on buzz sound,the  display will show L01 (press the Smart Recipes button again, will change to other recipes series, like steam recipes, display will show H01)；
2. Press to select the desired recipe code

Step 3: Start the cooking

• Press to start cooking.

Step 4: The END

When cooking is done, the oven will buzz 5 times, “END” will display on the screen and oven will back to standby mode; press to turn it off.

Operation of Separate Control

Step 1: Activate the product

• Connect the power.
• Press to enter into Standby Mode after powering on， display shows 888℃, 88:88 Min.

Step 2: Select Separate Control

The temperature setting of the upper heater and bottom heater. Upper heater’s temperature setting:

1. Press Separate Control, the icon on the display will flash;
2. Press , then and temperature flash；
3. Press to adjust the temperature.

Bottom heater’s temperature setting：

1. Press , then and temperature flash；
2. Press to adjust the temperature.

Time setting：

1. Press , then time flash；
2. Press to adjust the time.

Step 3: Start the cooking

• Press to start cooking.

Step 4: The END

When cooking is done, the oven will buzz 5 times, and “END” will display on the screen and the oven will back to standby mode; press to turn off.

Attention:

• If you wish to open the oven door during cooking, pause the cooking by pressing this button;
• if you are in steam or steam + grill mode, hot steam air will be released when you open the door.
• Therefore, please take a step back to avoid being scalded by hot steam air.

Notice for use

• If food is not cooked: It is recommended to use flat containers on the shelf, the food is better in small pieces, and the time needs to be adjusted according to the amount of food;
• If water shortage is still prompted after adding water: The amount of water added is not enough, please add water to the maximum water level mark and try again;
• Water shortage reminder: When the water tank water level is lower than the minimum water level requirement, the indicator light is on, the buzzer prompts, and the display continues to flash, fill water into water tank to the MAX level ;
• Automatic operation after preheating: After the preheating is completed, if there is no operation, the product will automatically enter the working state after beeping for ? minute;
• Fan delay cooling function: After the work is suspended or finished, the cooling fan will work for more than ? minutes to ensure safety and product life;

Lamp:

1. under standby mode, light is on when open the door or light is off;
2. Starting cooking, pause, and cooking is done, light will be off after 2 mins.

Operating Instruction

Cooking Functions Guide

Auto Menu ‒ Additional Functions

Attention: Default time, temperature set, advisable portion, etc for each menu/function are for reference ONLY; actual cooking time and temperature needed have to depend on the actual dishes you are cooking.

Attention: Preset recipes are for reference only. Cooking time and temperature may vary with actual ingredients and personal preference.

Maintenance

Precautions for cleaning and maintenance

1. After each use, the water in the water tank must be cleaned up in time to prevent excessive water from overflowing to the cabinet;
2. After using the steam mode, please pull out the remaining water in the water tank to prevent the remaining water from forming condensate or breeding bacteria in the water tank.

The following phenomena are normal

Attention

1. If the oven can’t work normally, please check
   • a. Is the power plug inserted
   • b. Whether the circuit breaker has tripped or blown
   • c. Is the door closed well
   • d. Is the water tank in place
   • f. Is the child-lock activated
2. If the steam oven is activated accidentally, please open the door immediately and power off.

Tips

• a. The cooling fan will work for 5 minutes after cooking is finished, for a delay to exhaust the heat in the cavity, which is a normal phenomenon;
• b. During work, if the door, the oven will pause work, closes the door, the oven will continue the work automatically;
• c. In any state, the water tank can be manually opened or closed.
• d. Suggest using pure water or distilled water to cooking in steam mode, after cooking, clean the residual water in the cavity to avoid scale inside the cavity.

Attention

1. Do not use cleaners containing alkali/soda, acid, or chlorine, nor use cleaning sprays, dishwasher cleaners or corrosive cleaners.
2. Do not use hard brushes, scouring pads, wire brushes, and other hard cleaning tools that will scratch the surface of stainless steel.

Maintenance method

Door assembly/display panel
The hard-to-clean dirt attached to the door can be cleaned with a neutral detergent, but not with a steel wire ball to avoid scratching the coating on the glass surface. After cleaning, dry it with a rag.
Door seal

1. After each use, please wipe the product seal with a sponge soaked in warm water, and then dry the door seal with a dry cloth;
2. Do not use cleaning agents to clean the door seal tape, because some components in the cleaning agent may corrode the tape;
3. The door seal tape may be perforated or cracked due to long-term use. If this happens, please replace it with a new one;

Cavity

1. After each use of the steam mode, please clean the cavity, use an absorbent sponge or a rag to wipe off the condensation on the cavity. It is best to open the door to dry the cavity;
2. After each use of the baking mode, please clean it up in time after the product has cooled down. The oil stains should be cleaned with a neutral detergent and wiped with wet cloth.

Attention

Be sure to shut down and unplug the power plug before repairing

1. The MAX water level of the water tank
   There is a MAX water level line on the water tank. please add water to this MAX line to extend the cooking time. Do not fill in water beyond the MAX line to avoid water splashing out when pulling the water tank.

2. A reminder of water shortage
   When the water shortage symbol is shown and with a beep, cooking will be stopped, please add water into the water tank.

3. About the choice of cooking utensils
   When choosing a cooking utensil for steam, please choose a porous container as much as possible. The depth of the container should not be too deep. The height of the steamed food should be 3~5cm so that the steam can contact the food more to ensure its taste.

4. The first use of the product produces a burnt smell
   Since the heater isolation will produce odor or smoke after high temperature, it is recommended to fill the water tank and steam for more than 45 minutes for the first time use, and let the oven cool down before formal cooking.

5. Not used for a long time
   If the product is not used for a long time, please clean the inside and use any baking mode to dry the remaining water in the cavity to avoid bacterial growth and odor.

6. Screen save energy
   After cooking, no operation for 10min, the screen will be lit off to save energy, just need to click it to wake up.

Troubleshooting

Wiring Diagram

DISTRIBUTED BY:

• LIVINOX MALAYSIA SDN.BHD.
• Block B-1-29, Dataran Cascades
• No. 13A, Jalan PJU 5
• Kota Damansara
• 47810 Petaling Jaya, Selangor
• Model No.: LCO-SB8-70

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>