VICTOR 6235P Contact Tachometer Instruction Manual

VICTOR 6235P Contact Tachometer

PRODUCT INFORMATION

Characteristics

1. Beautiful and elegant appearance design, convenient and comfortable to use;
2. Wide measurement range, and high resolution;
3. Single-chip microcomputer technology, photoelectric technology and anti-interference technology used, to accurately measure the rotation speed;
4. Super large-size LCD, with clear reading;
5. Automatically memorizing the measured maximum, minimum and the last displayed values;
6. Low power indication when the battery voltage is lower than the specified value;
7. Automatic off: Automatic off in about 15min when no key is operated.

Specifications

• Function: Photoelectric type
• Contact type: Contact line speed (metric system)
• Contact line speed: Contact line speed (British system)
• Display: 5-digit 16mm LCD
• Accuracy: Range selection: Automatic range
• Effective distance: 50mm-500mm
• Dimension: 157mm64mm31mm
• Power supply: 1*9V 6F22 batteries
• Power consumption: Less than 40mA
• Weight: About 200g (including batteries)
• Measurement range: 10-99999 rpm for photoelectric rotation speed
• Resolution: Photoelectric rotation speed: 0.1rpm (2.5-999.99rpm), 1rpm (above 1000rpm)

Operation Instructions

Starting up:
Load four 9V 6F22 batteries. Long press the ON/OFF key to switch it on or off, and short press this key for function selection.

Photoelectric rotation speed:
[Instructions for using the photoelectric type of rotation speed measurement]

Measurement Notes:
[Additional notes or precautions for accurate measurements]

Description of MEM Function:
When TEST key is released, the display will display 0 and current measurement mode, but the measured maximum, minimum and the last measured values are automatically stored in the instrument, and at this time, press MEM key for it to display the measured values, wherein MAX means maximum, MIN means minimum, and LA means the last value. Each time the MEM is pressed, another memorized value will be displayed.

Battery Replacement:

• When batteries are lower than 7V, LCD will display icon to prompt for battery replacement.
• Open the battery cover and take out batteries, and then correctly install batteries according to the identifications in the battery case.

Operating Manual of Intelligent Digital Tachometer

Characteristics

1. Beautiful and elegant appearance design, convenient and comfortable to use;
2. Wide measurement range, and high resolution;
3. Single-chip microcomputer technology, photoelectric technology and anti-interference technology used, to accurately measure the rotation speed;
4. Super large-size LCD, with clear reading;
5. Automatically memorizing the measured maximum, minimum and the last displayed values;
6. Low power indication when the battery voltage is lower than the specified value;
7. Automatic off: Automatic off in about 15min when no key is operated.

Specifications

Function|
---|---
Photoelectric type| △
Contact type|
Contact line speed

(metric system)

|
Contact line speed

(British system)

|

• Display : 5-digit 16mm LCD
• Accuracy : ± (0. 05%+5)
• Range selection : Automatic range
• Effective distance : 50mm-500mm
• Dimension : 157mm64mm31mm
• Power supply : 1*9V 6F22 batteries
• Power consumption : Less than 40mA
• Weight : About 200g (including batteries)
• Measurement range: 10-99999 rpm for photoelectric rotation speed
• Resolution: Photoelectric rotation speed: 0.1rpm (2.5-999.99rpm) 1rpm (above 1000rpm)

Operation Instructions

Starting up
Load four 9V 6F22 batteries. Long press the ON/OFF key to switch it on or off, and short press this key for function selecti

Photoelectric rotation speed:

• A : Stick one reflective marker on the object to measure.
• B : Long press ON/OFF key to switch it on, short press ON/OFF key to select the measurement mode photo RPM, and remove the contact accessory installed, if any.
• C : Press the TEST key to make the visible beam and the measured target in a line. Release the TEST key after the displayed value stabilizes and the measured maximum, minimum and the last displayed values will be automatically stored in the instrument.
• D : Press MEM key to display the maximum, minimum and the last measured values.

Measurement Notes

• A : Reflective marker: Cut off 12mm square adhesive tapes, and stick one on each rotation axis. Pay attention that the non-reflective area shall be larger than the reflective area. If the rotation axis obviously gives out light, first smear it with black paint or stick black tape, and then stick reflective marker thereon; rotation axis surface must be clean and smooth before sticking of the reflective marker.
• B : Measurement of low rotation speed: To improve the measurement accuracy, user is recommended to evenly stick more reflective markers on the measured object when the rotation speed is very low, and then divide the reading on the display by the number of reflective markers to obtain the actual measured value.
• C : Please take out the batteries if not to use the instrument for a long time, so as to avoid damaging the instrument by corroded batteries.

Description of MEM Function

When TEST key is released, the display will display “0” and current measurement mode, but the measured maximum, minimum and the last measured values are automatically stored in the instrument, and at this time, press MEM key for it to display the measured values, wherein “MAX” means maximum, “MIN” means minimum, and “LA” means the last value. Each time the MEM is pressed, another memorized value will be displayed.

Battery Replacement

• A. When batteries are lower than 7V, LCD will display icon to prompt for battery replacement.
• B. Open the battery cover and take out batteries, and then correctly install batteries according to the identifications in the battery case.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>