Panasonic F-PXV35A Air Purifier Instruction Manual

OPERATING INSTRUCTIONS
Air Purifier
Model No. F- PXV3 BA

F-PXV35A Air Purifier

This product is for indoor use only

Warranty card attached]

Thank you very much for purchasing this Panasonic product. Please read these operating instructions carefully before operation and maintenance. Also, be sure to read the “SAFETY PRECAUTIONS” section (P.2~5) before use.
Failure to comply with instructions could result in injury or property damage.
Make sure that the correct information is written on the warranty card, including the date of purchase and the name of the dealer. Keep the warranty card in a safe place along with the operating instructions for future reference.

CONFIRNATION AND SETUP

SAFETY PRECAUTIONS
Please strictly follow

• Disconnect power supply before maintenance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for the safety.
  Children should be supervised to ensure that they do not play with the product.

The safety precautions should be strictly followed in order to prevent injury or damage to properties.

• The following symbols differentiate the levels of danger or injury that may result if the product is not used correctly as instructed.

WARNING
Those things shown in this column indicate that there is possibility of causing death or severe injury.

CAUTION
Those things shown in this column indicate that there is possibility of causing minor injury or damage to properties.

• The following symbols are used to indicate the type of instructions that need to be followed. (The symbols given below are examples)

This symbol indicates an action that must not be performed.
Do not touch the power plug with wet hands.

■ Do not let the product get wet.

• Do not place cups, etc. on the product.
  (Otherwise, the product may short circuit with the possibility of fire or electric shock.)

This symbol indicates an action that must be performed.
Do not insert your fingers, metallic objects or others into the air inlet, air outlet or gaps.
(Otherwise, you may be hurt by the inner units with the possibility of electric shock or injury.)

WARNING
■ Do not pull the power cord when carrying or storing the product.
(Otherwise, the power cord may be damaged with the possibility of fire or electric shock.)
■ Do not damage the power cord or power plug.

• Do not cut, modify, excessive distort twist, squeeze the power cord, and do not place it near heat sources, place heavy weight on it, etc.
  (Otherwise, the power cord may be damaged with the possibility of fire or electric shock.)

■ Do not use power other than the rated voltage.
(Otherwise, the power cord may be overheated and induce fire.)
■ Do not disassemble or modify the product.
(Otherwise, the product may catch fire or malfunction, thus resulting in fire orelectric shock.)
→ Contact the dealer for repair.

■ In case of any abnormality or malfunction, stop using the product immediately and disconnect the power plug.

• The product stops operating when moving the power cord.
• If any buttons do not work.
• If the circuit breaker is tripped or when fuse blows.
• If the power cord or power plug becomes abnormally hot.
• If you notice a burning smell or an abnormal sound or vibration.
• If there is any other abnormalities or malfunctions.
  → Please stop using the product immediately and disconnect the power plug, and contact the dealer to check and repair.

****■ Clean the power plug regularly.
(If dust is found on the power plug, insulation may be damaged by humidity and fire may occur.)

• Disconnect the power plug and wipe it with dry cloth.
• When the product will not be used for a long period, disconnect the power plug.

■ Insert the power plug completely.
(If the power plug is not fully inserted, the power cord may be overheated, thus resulting in fire or electric shock.)

• Do not use damaged power plug or loose power socket.

CAUTION
■ Do not clean the product with gasoline or other volatile mix-ture solvents, and avoid contacting with spray insecticides.
(Otherwise, the product may crack or short circuit with the possibility of injury, fire or electric shock.)
■ Do not sit on or lean against this product.
(Otherwise, the product may fallover and injury may occur.)

• Families with children should pay more attention.

■ Do not operate this product in places where indoor fumigation type insecticides are being used.
(Chemical residue may build up inside the product and discharge from the air outlet, and cause damage to health.)
→ Ventilate the room with fresh air thoroughly after using insecticides before operating the product.
■ Do not place the product near combustible materials such as lighted cigarette, incense, etc.
(Otherwise, these may be absorbed into the product with possibility of fire.)

■ When disconnecting the power plug, hold the power plug instead of the power cord.
(Otherwise, the power cord may damage with the possibility of fire or electric shock.)
■ Keep the room well-ventilated when using the product together with a burner.
(Otherwise, carbon monoxide poisoning may Occur.)

• This product cannot remove carbon monoxide.

■ When carrying the product, please hold the left and right handles, but not the front panel.
(Otherwise, the product may fall off, injury may occur.)

■ Do not place the product in the following places.

• Incline and unstable place.
  (Otherwise, the product may fall over and injury may occur.)

• Where the temperature or humidity is too high, or watery area such as bathroom.
  (Otherwise, current may leak with the possibility of fire or electric shock.)

• Where oil fume is emitted, such as in kitchens.
  (Otherwise, the product may crack and injury may occur)

• Where oil or inflammable gas is present and maybe leaked.
  (Otherwise, a fire may occur due to ignition in the product.)

• Where the air outlet faces animals or plants directly.
  (Otherwise, it may cause discomfort to animals and dry out plant.)

SETTING AND OPERATING REQUIREMENTS

Area that can enhance the effectiveness!

■ Way to against PM2.5 and indoor dust, etc.
We recommend you to place the product on flat floor in the room.
■ Way to circulate air more effectively.
Place the product with its left, right and top about 30 cm or more away from walls, furniture or curtains, etc. Otherwise, the pollutants are difficult to be cleared.
To ensure effectiveness of this product, keep its back at least 1 cm away from the wall.
■ If the product is used in the same place for a long period.
Using the product continuously at the same location may result in dirty surrounding walls or floor. You are recommend to move the product away from where it is placed when maintenance it.
■ Do not use the same power socket with TV, radio, etc.
(Otherwise, visual disturbances or noises may be caused.
→ In this case, insert the power plug into another power socket.
■ Do not set the product in the following places.

• Where the product will be exposed directly to sunlight, outlet air of air conditioner or heat, etc.
  (Otherwise, deformation, degeneration, discolor or malfunction may be occurred.)

• Near equipment such as TV and radio.
  (Otherwise, visual disturbances or noises may be caused.)

→ Keep the product 1 m or above away from such devices.

■ Do not place any object on the product.
■ Do not place obstacles on the product air in let and outlet.
(Otherwise it may affect product performance.)

PRODUCT FEATURES

“House Dust Catcher” and “nanoe™  X” give you clean and fresh air.
■ House Dust Catcher completely cleaning dust from the airnear the floor
■ Equipped with nanoe™ X technology
■ Compact and stylish design
■ About nanoe™ X

• The so-called nanoe™ X are charged water purification particles generated by applying high voltage to separate water molecules.
• nanoe™ X features: high moisture content, small particles, high stability, etc.

1. High moisture content (the moisture content is 1,000 times the moisture content of ordinary anions).
2. Small particles (about 5 nm – 20 nm (nanometers) in size, able to penetrate deep into the fiber and stratum corneum).
3. High stability (6 times more stable than a common ion, covering a distance of 10 m or above).
4. More hydroxyl radicals (up to 4,800 billion of radical sare generated per second).
5. Weak acidity (with weak acidity features close to that of hair and skin).

All o f the above features have been tested by SGS-CSTC Standards Technical Services Co., Ltd.
Note: nanoe™ and the nanoe™ mark are trademarks of Panasonic Holdings Corporation.
nanoe™ X are particulate ions containing hydroxyl radicals whose amount is 10 times that of nanoe™.

MAIN PARTS IDENTIFICATION

Control panel

■ nanoe™ X indicator
The indicator lights on indicates nanoe™ X is being generated. nanoe™ X will be generated in all operation modes except you switch off it. (P.17)
■ Clean sign
Show the air pollution levels detected by odor sensor. The clean sign can be turned off. (P.18)

SETUP

Before Startup

1. Fill in the label with the first date of use. Notice
   Be sure to read P.2~5 before Startup.

2. Remove the deodorizing filter from poly bag.
   ① Remove the front panel. ② Remove the filters (2 types).③ Remove the deodorizing ilter from the poly bag.
   Notice
   Do not remove the black net of deodorizing filter. Install filters

3. Install the filters (2 types) and front panel.
   ① Install deodorizing filter.
   (There is no distinction between inside and outside, upper and lower) ② Install HEPA composite filter.
   (There is distinction between inside and outside, no distinction between upper and lower)③ Install front panel. Notice
   Be sure to install the front panel before use.
   Power-on
   

4. Connect the power plug.
   ■ When inserting the power plug, as the odor sensor uses the degree of cleanliness at this time as the standard, we recommend that you plug it in when the air is fresh (such as when there is no cigarette smoke). (The standard of the odor sensor automatically updates itself according to the degree of the indoor cleanliness.)
   ■ Press [Power off/0n] button, then the clean sign blinks for about 5 seconds.

OPERATION

Power Off/On
Turn on or off the product.
Press the button to operate. (Air volume indicator lights on)

1. When using for the first time, operation will begin with the air volume under “Auto”.
2. Other than the above situations, operation will begin with the air volume from the last time it was stopped.
3. Press the button again, the product stops operating.

■ To operate product within 2 minutes after the power plug is inserted, the indicator of air volume under “Auto” will blink about 2 minutes, what it indicates the odor sensor is in the standby mode.

Air volume
Select appropriate air volume for purifying air.
The indicator will be changed sequentially as figure below.

Turbo Timer

(Indicator lights on)
Turbo operation.
Press this button to begin turbo operation.

• During turbo operation, the clean sign will flash in blue and red.
  After 10 minutes, the turbo operation ends and will return to the previous operation mode.

■ Press the button again to deactivate turbo operation.
(The indicator turns off.)

Sleep

Sleeping operation.
When this button is pressed, the clean sign will turn off and operate with low air volume.
After 8 hours, the sleeping operation ends and the product stops operating.
■  Press the button again to deactivate sleeping operation. (The indicator turns off.)
Notice
■  If power failure occurs when product is operating, the product will restart automatically when power on again, and operate in the mode when power failure.

MAINTENANCE

WARNING
Make sure to disconnect the power plug before cleaning the product.
(Otherwise, the product might operate with the possibility of electric shock or injury.)
Notice

• For installation and removal methods of front panel and filters, please read P.10~11.

• When maintenance, do not leave the removed parts unattended.
  (Otherwise, it may cause tripping or damage.)

• Do not operate the product when the HEPA composite filter is removed.
  (Dust will be inhaled into product inner parts, and causes the product breakdown. The HEPA composite filter cannot function while it is removed.)

• Do not operate the product when the deodorizing filter is removed.
  (The deodorizing filter cannot function while it is removed.)

• When using chemically treated cloth, be sure to follow the instructions carefully.

• Do not use the detergents shown below.

Cleaning method

Filter replacement

| HEPA composite filter| Deodorizing filter
---|---|---
Replacement period| When the filter replacement indicator lights on. (About once every 3 years)※
Conditions| When the product inhales the smoke of six cigarettes every day. (Japan Electrical Manufacturers’ Association JEM 1467)

(Optional accessories: back cover)
※ Filter replacement period may be shorten, depending on the environment (such as where smoking is frequent).
Please replace it when ineffective.

1. After replacement, please connect power plug, then press button for about 3 seconds until the filter replacement indicator turns off, then the reset is completed.
2. Fill in installation date on the label attached with filter, then stick it on product to cover the old date. (P.10)

Notice

• The filter which needs to exchange cannot be used again even it is cleaned, please dispose it a s non-flammable garbage.
• If the product is used in a room (especially hotel) with strong odor such as aromatic smell, cigarette smoke or barbecue smell, these odors may adhere to the filter. When the adsorption capacity of filter reaches saturation, odor will also be blown out again with the wind because of excess adsorption. When there is above situation, please clean the HEPA composite filter. If the situation persists, please replace the HEPA composite filter and deodorizing filter, even if the filter replacement icon is off. In addition, if often used in a room with strong odor, please open the windows to ventilate the room regularly.

When idle for a long time

1. Disconnect power plug after turning off the product. (The product still consumes power even at rest.)
2. Maintain the product as usual.
3. Put the product into poly bag and carton, and keep it in a dry place. (If you overturn it or keep it flat, product malfunctions may occur.)

FURTHER INFORMATION

About nanoe™ X

• Mi nanoe™ X can be switched off.
  During operation, press and buttons at the same time for about 3 seconds to switch off. (nanoe™ X indicator lights off)
  Please press the buttons for about 3 seconds again to restart the nanoe™ X.

• Conditions for nanoe™ X generation
  nanoe™ X is generated using the air in the room. Therefore, depending on the temperature and humidity, nanoe™ X may not be generated stably.

  • Room temperature: about 5ºC~35°C (dew-point temperature: 2°C and above)
  • Relative humidity: about 30%~85 %

• When nanoe™ X is generated, small amount of ozone will be released. However, the quantity will be far less than the level in natural environment such as forest, and not be harmful to human beings.

About HEPA composite filter
The HEPA composite filter which with the Bio-sterilization and Super Allergy-buster can inhibit allergens (pollen, dead mites and feces), bacteria and mold.

• Super Allergy-buster: inhibits the activity of allergens (pollen, dead mites and feces).
  Testing authority: Osaka Municipal Technical Research Institute
  Test method: check the decrease of refined house dust mite allergen, by using enzyme immune measuring method.
  Inhibiting method: contact with Super Allergy-buster
  Target: allergens trapped by the filter (mites, pollen)
  Test result: inhibited 99% and above. (Daikou research report No. 2127)

• The HEPA composite filter may give off unique and harmless smell of “Green Tea Catechin”, “Bio-sterilization” and ‘ “Super Allergy-buster”.

About odor sensor
The sensor can detect the pollution of the air, and show the pollution level by indicator. The product can optimize the air volume automatically in auto operation according to the air quality.

•The wind generated when a door is opened or closed, or sudden temperature changes

• The sensor’s operation may vary depending on the indoor airflow condition if a heater is placed near the product in a room.
• The sensor is not designed to detect bacteria and viruses.
• The sensitivity of the sensor can be adjusted. (The default setting is “medium sensitivity” .)

1. Stop operating the product, then press and buttons at the same time for about 3 seconds. The air volume indicator will light on sequentially.
2. Please release the buttons, when the sensitivity is set as required.

FAQ

Please confirm the following before you put questions forward or send the product for repair.

Q1. Why is there a “jee” sound from the air outlet?

A. There is a slight sound when nanoe™ X is being generated. Depends on the environment and operation mode, the sound may be a bit loud or inaudible but it is not abnormal.

Q2. Why does the clean sign remain red even when the operation continues?

A. The indicator may illuminate red when the product is subject to steam or vapor emitting from sprayers.

Q3. Why does the clean sign remain blue even when the air is dirty?

A. Is the product placed in area where the dirty air is difficult to be cleared or the room size is too large for the product? (P.6, back cover)A. Is the product placed in area where the dirty air is difficult to be cleared or the room size is too large for the product? (P.6, back cover)

Q4. How to turn off the clean sign?

A. Please press Sleep (8H) and Air Volume buttons at the same time for about 3 seconds during operation to turn off. Please press the buttons for about 3 seconds again to relight.

TROUBLESHOOTING

If a problem i s encountered, please investigate it by going through the following items.
If the problem still persists, please disconnect the power plug and contact the dealer for repair.

dirty? (P.15)
→ Please clean it. If the situation persists, replace the filter with a new one.
② The air volume is small
③ The odor from the product is unpleasant| ■ Is the body, front panel or filter dirty? (P.15)
→ Please clean it. If the situation persists, replace the filter with a new one.
(The harmful carbon monoxide generated by cigarette cannot be removed)
■ Has the product ever been used in a room with strong odor?
If the product is used in a room with strong odor such as aromatic smell, cigarette smoke or barbecue smell, the filter replacement period may be shortened.
→ If you use the product in such environments, it is recommended to open the air ventilation system or open the windows to ventilate the room at the same time. If there is still strong odor to be blown out after the maintenance , please replace the HEPA composite filter and deodorizing filter , even if the filter replacement indicator does not light on.
④ The sensor sensitivity can not be set up| ■ Is the product turned on?
Sensor sensitivity can not be set up unless the product turned off.

If any of the following cases occur, please contact the dealer immediately for repair.

All the air volume indicators are blinking| ■ Product may be out of order.
→ Please disconnect the power plug and contact the dealer for repair.
---|---

SPECIFICATIONS

220 V-230 V∼ 60 Hz
Air volume settings| Hi| Med| Lo
Power consumption (W) ※1| 24| 9| 6
Air volume (m3/min)| 3.5| 2.0| 1.0
Floor area capacity ※2| Up to 26 m² in a standard household room
Power cord length| 2.0 m
Product dimension| 300 mm x 189 mm x 520 mm (WxDxH)
Product weight| 4.8 kg

※1 The power consumption is about 0.8 W when the operation is set to “Off”. (With the power plug inserted).
※2 Floor area capacity is based on JEM1467, under the condition of Hi speed.
(Japan Electrical Manufacturers’ Association)
Note: This product cannot remove hazardous substances such as carbon monoxide from the cigarette smoke.

OPTIONAL ACCESSORIES

• Replacement HEPA composite filter
  Part No.: F-ZXMP35Z

• Replacement deodorizing filter
  Part No.:F-ZXFD35X

Please contact dealer

• All the air volume indicators are blinking.
  Product may be out of order.
  Please disconnect the power and contact the dealer for repair.

Panasonic Corporation
Web Site:http://www.panasonic.com
© Panasonic Corporation 2022
Issue date:12/2022
P1222-0 PXV3A8953

Documents / Resources

| Panasonic F-PXV35A Air Purifier [pdf] Instruction Manual
F-PXV35A Air Purifier, F-PXV35A, Air Purifier, Purifier
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>