Moes WS-US-RF Multi-Control 3 Gang Wi-Fi + RF Smart Switch Instruction Manual
- June 4, 2024
- MOES
Table of Contents
**Moes WS-US-RF Multi-Control 3 Gang Wi-Fi + RF Smart Switch Instruction Manual
**
Product Description
This new designed glass panel wireless touch smart switch is designed with WiFi + RF to replace traditional switches with a variety of ways to control. Now one new smart feature as multi-control association to other smart switches is added into the Smart Life/Tuya App, together with the backlight on/off and relay status.And its scratch resistance glass panel is suitable for different decoration styles with its best value.
Note: Button sound on and off: no button operations before operations begin within 6 seconds.Then press switch button for 4 times and long press for the fourth time until the switch beep sounds as Di-Di for 2 times for successful operation.
Safety Information
Risk of Electric Shock: Electricity can cause personal injury and property damage if handled improperly. If you are not sure about any part of these instructions, please seek professional assistance from a qualified electrician.
Technical Parameters:
Model: WS-EU-RF / WS-US-RF
Voltage: 90-250V AC, 50/60Hz
Max. Current: 10A/Gang; Total 10A
Wireless Protocol: Wi-Fi 2.4GHz+RF433MHz
Warnings
Turn off the power at the circuit breaker and test that power is off before wiring.
Installation
Note:
- Install the switch with electricity off.
- Do not install in damp environment.
- Neutral wire in not required(single live line).
- Do not exceed the maximum load.
- Please follow instructions and properly install.
- If you don’t have any wiring experience, please call a professional electrician.
Step 1
- Turn off the circuit breaker and use the electrical tester to test the power.
- Ensure the switch is off before wiring.
Step 2
- Remove the old switch
Step 3
Remove the switch and pull it away from the wall.
ldentify Line/Load Wire(Note: The color of your wire may be different from the
color shown on the manual.)
Verify power is off
- We recommend you remove the faceplate from the old switch and use an electrical tester to test all wires connected to the switch to ensure there is no voltage in the circuit.
- You may need to turn off more than one circuit breaker.
Step 4
-
Take pictures of the wiring
-
Follow the wiring diagram to connect the switch wires to the wires in the wall box with the wire conductors.
Step 5
- Remove the panel with screwdriver
(Please don’t install with electricity power on)
Step 6
-
Prepare to install wiring
A. Live wire connects “ L ” terminal
B. Lamp wire connects “ L1,L2,L3,L4 ” terminal
1 Gang connects “L1” terminal
2 Gang connects “L1,L2” terminal
3 Gang connects “L1,L2,L3” terminal
4 Gang connects “L1,L2,L3,L4” terminal -
Capacitor Installation
When the lamp lights or starts flashing, Please connect Capacitor the as shown in the drawing:
1 Gang L1 and N line.
2 Gang L1 and N line.
3 Gang L1 and N line.
4 Gang L1 and N line.
1-3 Gang
4 Gang
Step 7
- Put the switch into switch box in the wall
- Mount the two side screws
- Install the glass panel (install from up above)
- Finish installation
Add Devices
-
Download Smart Life App
Please scan the QR code or download Smart Life on App store. -
Registration or Log in
- Download “Smart Life” Application
- Enter the Register/Login interface; tap “Register” to create an account by entering your phone number to get verification code and “Set password”. Choose “Log in” if you already have a Smart Life account.
-
Configure the APP to the switch
- Preparation: Ensure the switch has been connected with electricity; ensure your phone has been connected to Wi-Fi and is able to connect to the Internet.
Note:
The switch only supports 2.4G network. If you have connected 5G network, please disconnect 5G network firstly and connect 2.4G network.
Wi-Fi link method:
Pair and clear up the WiFi code(New Updated)
-
Make sure your phone is connected to Wi-Fi and Bluetooth.
-
Open Smart Life/Tuya App and Click“+”, then the promptpage will automatically show on the screen. Click “Go to add”.
-
Select the device you want to add and click “Add”
-
Enter Wi-Fi Password and click “Confirm”, waiting for completing the connection.
-
Add the device successfully, you can edit the name of the device to enter the device page by click “Done”
How to reset/repair Wi-Fi code
Press the switch button for 6 times, and hold on the 6th time, then release
until you hear Di-Di-Di(3 times),and the blue indicator on the switch will
flash fast after 3 seconds. Reset/repair is successful.
Remote radio frequency (RF)link method:
Pair and clear up the RF code
How to pair the RF code
-
(can be turned on and off): Confirm your switch is off before operations. Press the switch button for about 8 seconds until you hear Di-Di(2 times).Then the matching of RF code is successful. The key of the remote controller can control the switching of the state of the switch on and off corresponding to the position of the switch.
-
(Open only): Confirm your switch is off before operations.-
Press the switch button for about 5 seconds until you hear Di(1 time).After that, release the button, press the corresponding button on the remote control to turn on. Then the matching of RF codes is successful. The key of the remote controller can control the corresponding position of the switch to be open. -
(Close only): Confirm your switch is on before operations.
Press the switch button for about 5 seconds until you hear Di(1time).After that, release the button, press the corresponding button on the remote control to turn on. Then the matching of RF codes is successful. The key of the remote controller can control the corresponding position of the switch to be closed.
How to clear up the RF code
Confirm your switch is off before operations. Press the switch button for a
long time until you hear Di-Di-Di-Di(4 times), and then release the button.
The RF code is now cleared up.
How to achieve multi-control association
Note: Please confirm you have successfully finished the WiFi link method above for adding this switch to your Smart Life App before the association.
-
WiFi add another smart switch to the same Smart Life/Tuya App.(If there is a smart switch having been added before to the app, just go to next step.) Note: There is no need to wire the new added switch to the light, only L and N are required for wiring.
-
Then you will see two devices in the app and click the main switch(as One gang switch as below) by entering into the next operation.
-
Click in the upper right corner and choose “Multi-Control Association, and then click “+” in the right corner.
-
Choose the switch that you want to associate to and then choose the switch button that you want to control the same light.
-
Then go back to previous page, you will see two items in the page, one is your main switch, the other is the one you associate just now.
Note: Please confirm the associated switch is enabled. -
Now you are able to control your light with two switches. Do not associate another button in the same switch for multi-control.
-
If you want to add another third or more smart switches to control your light, just repeat the steps above. And you will see the result as below when you associate another new switch.
Set your Echo speaker by Alexa APP
-
If you have finished installing Smart Life, just open Amazon Alexa App; log into your Alexa account with password.
-
Click the menu on the top left -click “settings”, choose “Set up a new device”(choose a device like Echo)
Note:
When below page appears,long press the small dot on your Echo device until the light turns to yellow. Then click “Continue” on the App.
Attention: The mobile phone can not open a variety of VPN software. -
Choose your own Wi-Fi and wait for a few minutes. After watching an introduction video, click “next step”, then it will enter Home page automatically. Now the Echo has been connected to Wi-Fi successfully.
Enter Smart Life Skill in Alexa APP
Complete product networking configuration in the App
Complete the device’s networking configuration according to the prompts in the App.
Note: In the App, change the name of the device to an easily identifiable name such as Alexa; names are usually in English, such as “bed light”.
Configure the Amazon Echo device
(If you have already configured Amazon Echo, you can skip this step. The following instructions are based on the iOS client.)
-
Make sure you Amazon Echo device is powered on and connected to a Wi-Fi network.
-
Open the Alexa App on your phone. After successful login, tap on the menue in the upper left corner of the Home page, select “Settings” and tap “Set Up A New Device” to set up the Amazon Echo.
Choose your Amazon Echo device type and language for connecting. Press and hold the small dot on the device until the light turns yellow. Then tap “Continue” to connect to the hotspot. -
After connecting to the Amazon Echo hotspot, return to the page. At this point, the connection is successful.
Tap “Continue” to proceed to the next step. Choose a Wi-Fi
network to connect to. Amazon Echo will take a few minutes to try to connect
to the network.
- After the network connection is successful, tap “Continue”.
An introduction video will appear. After the video ends, tap “Continue” to jump to the Alexa Home page. You have now completed the Amazon Echo’s configuration process.
Key step —— Link Skill
-
Tap on “Skills” in the Alexa App menu.
-
Then search for “App Name”. Tap “Enable” to enable the Skill.
-
Enter the App account and password, then tap “Link Now” to link your App account to enable the Skill. Now you can start your smart home journey
Common commands
Control the device via voice commands, now you can control your smart device with Echo. You can control your device (such as your bedroom light) with the following commands:
Alexa, turn on/off bedroom light. (Turn on/off the light)
Alexa, set bedroom light to 50 percent. (Set the light to any brightness)
Alexa, brighten/dim bedroom light. (Increase/weaken the brightness of the
light)
Alexa, set bedroom light to green. (Adjust the color of the light)
SERVICE
- During the free warranty period, if the product breaks down during normal use, we will offer free maintenance for the product.
- Natural disasters/man-made equipment failures, disassembly and repair without the permission of our company, no warranty card, products beyond the free warranty period, etc., are not within the scope of free warranty
- Any commitment (oral or written) made by the third party (including the dealer/service provider) to the user beyond the warranty scope shall be executed by the third party
- Please keep this warranty card to ensure your rights
- Our company may update or change the products without notice. Please refer to the official website for the updates.
RECYCLING INFORMATION
All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19 / EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.
WARRANTY CARD
Product Information
Product Name__
Product Type
Purchase date__
Warranty Period____
Dealer Information__
Customer’s Name
Customer Phone____
Customer Address__
Maintenance Records
| Failure date | Cause Of Issue | Fault Content | Principal |
|---|---|---|---|
Thank you for your support and purchase at we Moes, we are always here for
your complete satisfaction, just feel free to share your great shopping
experience with us.
If you have any other need, please do not hesitate to contact us first, we will try to meet your demand.
@moessmart
@moes_smart
@moes_smart
moes
@moes_smart
www.moes.net
WENZHOU NOVA NEW ENERGY CO.,LTD
Address: Power Science and Technology Innovation
Center, NO.238, Wei 11 Road, Yueqing Economic
Development Zone, Yueqing, Zhejiang, China
Tel:+86-577-57186815
Email: service@moeshouse.com
AMZLAB GmbH
Laubenhof 23, 45326 Essen
Made In China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>