BRAYER BR4015 Steam Iron Instruction Manual

BRAYER BR4015 Steam Iron

Product Information

• The Steam Iron BR4015 is a versatile iron designed for ironing bedding, clothes, and for vertical steaming of fabrics. It can be used with or without a power cord using the detachable iron base. The iron features a water spray nozzle, water inlet lid, continuous steam supply knob, burst of steam button, water spray button, and a heating element with an on/off and automatic switch-off function.
• For additional safety, it is recommended to install a residual current device (RCD) with a nominal operation current not exceeding 30 mA.
• The iron surfaces get hot during operation, so it is important to avoid contact with open skin areas to prevent burns. Children should not be allowed to play with polyethylene bags or packaging film to avoid the danger of suffocation. The unit is intended for household use only and should not be used for commercial or laboratory purposes.
• Before the first use, unpack the iron and wait for at least 3 hours if it has been stored at a negative temperature. Ensure that the supply voltage of the unit corresponds to the specifications of your mains.
• The iron can be used wirelessly for approximately 20 to 30 seconds before the next cycle of soleplate heating. When using tap water, it is recommended to mix it with distilled water in the specified proportions to prevent scale buildup.
• When filling the water tank, ensure that the iron is switched off and unplugged. Refilling the water tank during ironing should be done with the iron switched off and the power plug removed from the main socket.
• Before using the iron for the first time, test the heated iron on a piece of cloth to ensure that the soleplate and water tank are clean. The iron has different temperature settings for different fabrics.
• The iron has an anti-drip valve to prevent water from leaking out of the soleplate holes. If steam is not supplied during operation, check the temperature control knob, steam supply knob, and the water level in the water tank.

Product Usage Instructions

1. Ensure that the iron is switched off and unplugged before filling the water tank.
2. Open the water inlet lid and fill the water tank with distilled water or a mixture of tap water and distilled water, as specified.
3. Close the water inlet lid securely.
4. If needed, refill the water tank during ironing by switching off the iron and removing the power plug from the main socket.
5. Before using the iron for the first time, test it on a piece of cloth to ensure cleanliness.
6. Select the appropriate ironing temperature based on the fabric being ironed. Refer to the provided temperature guide for guidance.
7. For dry ironing, simply glide the iron over the fabric without using steam.
8. For steam ironing, ensure that the temperature control knob and steam supply knob are set properly. Check the water level in the water tank.
9. If steam is not supplied during operation, check the temperature control knob, steam supply knob, and water level in the water tank.

IRON BR4015
The iron is intended for ironing bedding, and clothes, and for vertical steaming of fabrics. You can use the iron with or without a power cord using the detachable iron base.

DESCRIPTION

1. Water spray nozzle
2. Water inlet lid
3. Continuous steam supply knob
4. Burst of steam button
5. Water spray button
6. Heating element on/off /automatic switch-off indicator
7. Handle
8. Iron lock on removable base « , »
9. Power cord protection
10.  Detachable iron base
11. Water tank
12. Iron soleplate
13. Temperature control knob
14. SELF-CLEAN button «Self- Clean»
15. Beaker

ATTENTION!
For additional protection it is reasonable to install a residual current device (RCD) with nominal operation current not exceeding 30 mA, to install RCD, contact a specialist.

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the iron, after reading keep them for future reference

• Use the unit for its intended purpose only, as it is stated in this manual.

• Mishandling the iron can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.

• Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.

• The power cord is equipped with a «euro-plug»; insert it into a socket that has a reliable grounding connection. In case of short circuit the grounding reduces the risk of electric shock.

• Contact an electrical technician, if you are not sure that your sockets are installed properly and grounded.

• To avoid fire, do not use adapters for connecting the unit to the mains.

• To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.

• Do not touch the unit body, the power cord and the power plug with wet hands.

• Do not let the power cord be on the ironing board and touch hot surfaces and sharp edges of furniture.

• Do not use the unit near heating appliances, heat sources or open flame.

• Do not use the unit in proximity to the kitchen sink, in bathrooms, near swimming pools or other containers filled with water.

• If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water. Apply to the authorized service center for testing or repairing the unit.

• Do not use the unit in places where aerosols are used or sprayed, and in proximity to highly inflammable liquids, do not use the unit in the places where such liquids are stored.

• Do not use the unit outdoors.

• It is recommended not to use the unit during lightning storms.

• Protect the unit from impacts, falling, vibrations, and other mechanical stress.

• Do not leave the unit unattended. During breaks in operation, put the iron on the base (in a vertical position).

• Before plugging the unit in set the temperature control knob to the minimal position and switch the continuous steam supply off.

• Always switch off and unplug the iron when you do not use it.

• Fill the tank with water additionally clean with a domestic filter.

• Do not fill the water tank with carbonated water, scented liquids, vinegar, starch solution, descaling reagents, chemical agents etc.

• Make sure that the water level in the tank is not above the MAXimal mark «MAX».
  ATTENTION! The surfaces of the iron get hot during operation. Avoid contact of open skin areas with hot surfaces of the iron or outgoing steam to avoid burns.

• Never steam clothes directly on a person, always use a clothes hanger or a stand.

• Do not use the power cord as a carrying handle for the iron.

• Switch the unit off and unplug it after the use or before cleaning.

• When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.

• To avoid electric shock do not immerse the iron, the power cord and the power plug in water or any other liquids.

• Before taking the iron away, let it cool down completely and pour out the remaining water.

• Clean the unit regularly.

• For child safety reasons do not leave polyethylene bags used as packaging unattended.
  Attention! Do not allow children to play with polyethylene bags or packaging film. The danger of suffocation!

• The unit is not intended for use by children.

• Do not leave children unattended to prevent using the unit as a toy.

• Do not allow children to touch the operating surface, the unit body, the power cord, or the power plug during the operation of the unit.

• Be especially careful if children or disabled persons are near the operating unit.

• During the unit operation and breaks between operation cycles, place the unit out of reach of children.

• The unit is not intended for usage by physically, sensory, psychically, or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.

• From time to time check the power cord insulation integrity.

• If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service, or similar qualified personnel to avoid danger.

• Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.

• To avoid damages, transport the unit in the original package.

• Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.

• Unpack the iron and remove any packaging materials and advertising stickers.
• If there is a protective film on the soleplate (11), remove it.
• There may be water residue in the tank (10), as the iron has undergone factory quality control.
• Keep the original package.
• Read the safety measures and operating recommendations.
• Check the delivery set.
• Examine the unit for damages, in case of damage do not plug it into the mains.
• Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
• Clean the iron body and the soleplate with a soft, slightly damp cloth and then wipe it dry.

OPTIONS OF USING THE IRON

• You can use the iron both with the power cord and wirelessly.
• For the power cord option, do not remove the base (10), but set the latch (8) to position « ».
• To use the wireless option, place the base (9) on a flat, stable surface, taking care to keep the power cord away from hot surfaces and sharp edges of furniture.
• Set the latch (8) to position « ».
• Fill the iron reservoir (11) with water (see the recommendations in the «SELECTING WATER» section).
• Use the regulator (13) to set the desired iron soleplate temperature (12) (see «IRONING TEMPERATURE»).
• Place the iron on detachable base (10).
• Insert the power plug into the mains socket, the indicator (6) will light up.
• When the indicator (6) goes out, you can start using the iron.

Note:

• The possible use time of the iron in the wireless variant from 20 to 30 seconds, it would seem that this is not much, but in practice this time is enough  until the next cycle of the iron soleplate heating (12), when placing the iron on the removable base (10).
• when the unit is switched on for the first time a foreign smell can appear – it is normal and is not covered by warranty.

WATER SELECTION

• Use tap water to fill the water tank (11) of the iron.
• If tap water is hard, it is recommended to mix it with distilled water in proportion 1:1. If tap water is too hard, mix it with distilled water in proportion 1:2 or use distilled water only.

FILLING THE WATER TANK

ATTENTION!
Before filling the water tank (11) with water make sure that the iron is switched off and unplugged.

• Set the temperature control knob (13) to the position «MIN», and the continuous steam supply knob (3) to the position « ».
• Open the water inlet lid (2).
• Pour the water into the water tank using the beaker (11) and then close the lid (2).

Notes:

• do not let water go over the «МАХ» mark when filling the water tank (11);
• if you need to refill the water tank during ironing, switch the iron off and remove the power plug from the mains socket.

IRONING TEMPERATURE

Before using the iron for the first time test the heated iron on a piece of cloth to be sure that the iron soleplate (12) and the water tank (11) are clean.

• Before ironing check the recommended ironing temperature indicated on the tag.
• If the item label is marked with the symbol « do not iron the item.
• If there is no label on the clothes item, but you know the type of fabric, refer to the following table to determine the proper temperature.
• This table is only valid for smooth materials.
• Fabrics of other types (crimped, raised, etc.) are best ironed at low temperatures.
• Sort items by ironing temperature first: synthetics with synthetics, wool with wool, cotton with cotton.
• The soleplate (12) heats up faster than it cools down, that’s why you should start ironing with synthetics, then increase the temperature and iron silk and wool items. Cotton and linen items should be ironed last.
• If an item is made of mixed fabrics, set the lowest ironing temperature. For instance, if an item is made from polyester and cotton, set the ironing temperature for synthetics «•».
• If you cannot define the fabric structure, find a place that is inconspicuous while wearing and select the ironing temperature experimentally (always start with the lowest temperature and raise it gradually until you get the desired result).
• Corduroy and other fabrics that can become glossy should be ironed backside.

DRY IRONING

• Place the iron on the detachable base (10) on a flat, stable surface.
• Insert the power plug into the main socket.
• Set the steam supply knob (3) to the position « » (the steam supply is off).
• Set the desired ironing temperature by turning the knob (13): «•», «••», «•••» or «MAX», depending on the type of fabric; the indicator (6) will light up.
• When the iron soleplate (12) reaches the set temperature, the indicator (6) will go out and you can start ironing.
• You can use the iron either with the power cord or wirelessly (see «OPTIONS OF USING THE IRON»).
• After you finish ironing, set the temperature control knob (13) to the «MIN» position.
• Disconnect the power plug from the mains socket and wait until the iron soleplate (12) cools down completely.

STEAM IRONING

The iron has an anti-drip valve that shuts off the water supply when the iron soleplate temperature is low (12), this prevents water from leaking out of the iron soleplate holes (12).
Steam ironing is possible only if the temperature control knob (13) is set to the steam mode «•••» or «MAX».

• Place the iron on the detachable base (10).
• Insert the power plug into the mains socket.
• Make sure that there is enough water in the water tank (11).
• Turn the control knob (13) to set the required ironing temperature in the steam mode «•••» or «MAX», the indicator (6) will light up.
• When the temperature of the soleplate (12) reaches the set point, the indicator (6) will go out and you can start ironing.
• You can use the iron either with the power cord or wirelessly (see «OPTIONS OF USING THE IRON»).
• Set the necessary steam intensity with the continuous steam supply knob (3): steam will be released from the openings of the soleplate (12) only if the iron is in horizontal position. To stop the steam supply, put the iron vertically or set the knob (3) to the position « » (steam supply is off).
• After you finish ironing, set the temperature control knob (13) to the position «MIN», and the continuous steam supply knob (3) to the position « » (steam supply is off).
• Disconnect the power plug from the mains socket and wait until the iron soleplate (12) cools down completely.

ATTENTION! If steam is not supplied during the operation, check whether the temperature control knob (13) and the steam supply knob (3) are set properly and whether there is water in the water tank (11).

WATER SPRAY

• Make sure that there is enough water in the water tank (11).
• Press the water spray button (4) to dampen the fabrics.

BURST OF STEAM

• The burst of steam is useful for ironing folds and can be used only in the high temperature ironing mode; set the temperature control knob (13) to the position «•••» or «MAX».
• When pressing the burst of steam button (5) steam will go out of the iron soleplate (12) openings intensively.

Note: to avoid water leakage from the soleplate (12) openings, press the burst of steam button (5) with 4-5 sec. intervals.

VERTICAL STEAMING

• Vertical steaming of fabrics or interior objects can be performed only in the high temperature ironing mode. Set the temperature control knob (13) to the position «•••» or «MAX»).
• Hold the iron vertically at the distance of 5-20 cm from the clothes or interior objects and press the burst of steam button (5) with 4-5 second intervals, steam will be released from the soleplate (12) openings intensively.

ATTENTION!

• To avoid fabric melting, do not touch it with the iron soleplate (11) while steaming.
• Do not steam clothes on a person. Use a clothes hanger or a coat rack.
• After you finish ironing, switch the iron off and unplug it, wait until the iron soleplate (12) cools down completely, then open the water inlet lid (2), turn over the iron and drain the remaining water.

STEAM CHAMBER CLEANING

• Regularly clean the steam chamber of the iron, especially in the regions with «hard» tap water.
• Set the continuous steam supply knob (3) to the position « » (steam supply is off).
• Open the lid (2), fill the tank with water up to the MAXimal mark «МАХ» and close the lid (2).
• Place the iron on the detachable base (9).
• Insert the power plug into the mains socket.
• Set the temperature control knob (13) to the «MAX» position, the indicator (6) will light up.
• When the iron soleplate (12) reaches the set temperature, the indicator (6) will go out and you can start cleaning the steam chamber of the iron.
• Remove the power plug from the mains socket.
• Remove the iron from the base (10).
• Hold the iron above the sink horizontally, press and hold down the button (14) «SELF-CLEAN».
• Boiling water and steam with scale will be intensively released from the soleplate (121) openings.
• Slightly sway the iron back and forth, until all the water leaves the water tank (10).
• Place the iron on the detachable base (10) and allow the iron soleplate (12) to cool completely.
• After the soleplate (12) cools down, wipe it with a dry cloth.
• Before taking the iron away for storage make sure that the water tank (11) is empty, andthe iron soleplate (12) is dry.

CLEANING AND MAINTENANCE

1. Before cleaning make sure that the iron is switched off and cold and the power plug is not connected to the mains socket.
2. Wipe the iron body with a slightly damp cloth and then wipe it dry.
3. You can remove the mineral deposit from the iron soleplate (12) with a cloth soaked in table vinegar.
4. After removing the mineral deposit polish the soleplate (12) surface with a dry clean cloth.
5. Do not use abrasives or solvents to clean the iron soleplate (12) and body.
6. Avoid contact of the iron soleplate (12) with sharp metal objects, as well as with metal buttons, zippers etc.
7. Do not immerse the iron, the power cord and the power plug into water or any other liquids.

STORAGE

• Before taking the iron away for storage drain the remaining water from the water tank (11) and clean the iron.
• Set the temperature control knob (13) to the position «MIN» and switch the continuous steam supply knob (3) to the position « » (the steam supply is off).
• Secure the iron to the detachable base (10) with the latch (8) in the « » position.
• Wind the power cord around the base (10).
• Store the iron vertically in a dry cool place out of reach of children and disabled persons.

DELIVERY SET

1. Iron – 1 pc.
2. Detachable base – 1 pc.
3. Beaker – 1 pc.
4. Instruction manual – 1 pc.

TECHNICAL SPECIFICATIONS

• Power supply: 220-240 V, ~ 50/60 Hz
• Rated input power: 2400 W
• Water tank capacity: 300 ml
• Continuous steam: 25 g/min
• Steam release: 140 g/min

RECYCLING

• To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling.
• The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner.
• For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product.
• The manufacturer reserves the right to change the design, structure and specifications not affecting general operation principles of the unit, without prior notice.
• The unit operating life is 3 years
• The manufacturing date is specified in the serial number.
• In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

brayer.ru

References

• BRAYER - официальный сайт австрийского бренда бытовой техники

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>