Audio Authority 903i Digital Control Panel For Access User Guide
- June 13, 2024
- Audio Authority
Table of Contents
Audio Authority 903i Digital Control Panel For Access User Guide
Introduction
The Model 903i Comparator is a 10 inch capacitive touchscreen that connects to any AccessTM switching system, providing an easy way to select products and compare systems.
Read and follow these instructions carefully. If you have any difficulties during the installation, don’t hesitate to call us for assistance! We’re open Monday through Friday from 8:30 AM until 5:00 PM, Eastern Time. Also check our website for template diagrams and tips: audioauthority.com/access_tips.
Features:
- Multiple Product Group cards
- Swipe through product selections, up to 99 products per group
- Compare Systems mode for easy A/B system comparison
- PIN protection for setup features
- Lock feature disables the comparator, unlock with PIN
In addition to a 903i Comparator, the Access System can also be operated by:
- Product Select Buttons – push-button located next to each product
- 906 Control Panel – controls one group of products · Custom controller via RS-232
The Access System is unique in that all of these different modes of product selection may be used in the same system. This means that your system could contain a 903i Comparator, Control Panel, and Product Select Buttons.
Model 903i Comparator – Rear View
Configuring the 903i
In the upper right corner of the 903i is the MENU icon. The drop down menu
provides the following selections: Help, About, Lock, and Admin.
HELP – This shows customers how to use the 903i. Touch OK to exit
this screen.
ABOUT – Provides the 903i software version and manufacturer contact
information. Touch OK to exit this screen.
LOCK – The 903i may be “locked” to prevent unauthorized use. Choose Lock from
menu and enter PIN to lock the screen. If Lock is accidentally selected and
the correct PIN is not entered within 30 seconds, the 903i returns to the main
screen.
Note: The Access System is still functional while the 903i is locked; if
product select buttons are installed, the system operates.
ADMIN – Use these settings to create PIN protected access, Poll the Access
system (see page 4) for Group identification, and set up the product groups.
Set PIN
The default PIN is
1234. To change the PIN, select Set PIN from the menu. Using the numeric pad,
enter a new PIN code and select OK. Press the checkmark button to exit this
screen. Use this PIN to Lock/Unlock the 903i. When the 903i is locked, the
switching system is still operational, but customers cannot use the
Comparator.
Poll on Start
The 903i Polls the Access modules that are connected to the system if Poll on Start is ON (Always). After the system is configured, touch Poll on Start and slide the button on the right to the OFF position.
Sleep While Locked
The Sleep While Locked function powers down the entire Access switching system whenever the 903i is locked. While Poll on Start switch. locked, the Comparator and PSBs are disabled, and a message on the 903i instructs customers to ask for assistance. If this function is off (box unchecked), the system remains powered while the 903i is locked, and PSBs (if present) may be used to operate the system.
Setup
Name the groups and if necessary, enter the number of product positions used
within each group. Bypass may also be activated for the Electronic groups.
When Bypass is engaged, the fourth position of the last module is hidden
(shown in the last figure to the right). This is useful for demonstrating
equalizers or car amplifiers. For Bypass, you must also set the Bypass switch
on the switching Module (942, 958, etc.).
Delete Setup
To reconfigure the 903i touch Delete Setup, choose OK from selection window,
and restart the 903i. Previous settings and group names are deleted and the
903i polls the modules to create blank group cards.
Operation
Selecting Products
Select a product from each product group on the 903i:
- Touch a product number in a group to activate a position.
- Scroll to the desired Product Group card if that Group is not already visible.
- Activate a complete system to hear audio.
Speaker Add
To play multiple pairs of speakers in the same Speaker Group (default Speaker
Limit=2):
- Select a speaker pair.
- Long-press the icon of the second speaker pair you wish to add.
- Long-press a third speaker pair and the first pair deselects.
The Product Group card will display the two speaker pair numbers. You may add more speaker pairs in the same manner (depending on system limitations set during installation), but remember that you could be presenting a severe load (low impedance) to the amp’s output, so be careful. Before you increase the speaker limit, check the receiver or amplifier manufacturer’s recommendations for maximum number of speakers.
To deselect one of the speaker pairs playing in the same Product Group: 1. Press Previous Selection to return to the first speaker selected, or 2. Press one of the selected pairs in that Product Group.
Note: The maximum number of speakers that can play at the same time is determined by DIP switch settings on the 980 System Module. If you cannot select multiple speakers to play simultaneously, please refer to the Installation Manual’s instructions on setting the 980 System Module or call Tech Support at 800-322-8346.
To turn off all products within a Product Group, touch the active product within that group. You can play car audio head units without amplifiers if you have Bypass configured.
Comparing Systems
A “system” is made up of one of each of the components required to play audio
(e.g. source, amplifier, pair of speakers). You may compare two different
systems using the 903i. This mode switches all groups at once with a single
touch.
- Once a system has been selected, press Compare Systems to enter the dual comparison screen. The system you have configured will be the “A” system on the left. The “B” system may now be selected from the Product Groups in the right hand column. Touch the right hand column to select the “B” system.
- Compare the two systems by touching the darkened half of the screen, left and right. You may change any of the products in the active system.
Installation
Download the template available at audioauthority.com/903i if you are mounting the 903i in a fixture or wall.
- Print the template at full scale (100%) and drill the six holes indicated. Cut a 10.750″ x 6.750″ opening for the 903i to mount in your display or other surface.
- Connect the USB serial device to Serial Adapter system bus port to any vacant Access System Bus header. Connect the USB mini to the 903i USB port (see 903i connection diagram). Securely mount the USB serial device. Connect Power and bottom cover.
- Mount the 903i and then attach the bezel using the screws provided.
Note: Only Power and USB ports are used on the tablet, other ports are not used.
Using PSBs
Product Select Buttons (PSBs) make a powerful addition to the merchandising
flexibility of systems that use the 903i. If you have both a 903i Comparator
and PSBs, notice that any selection made with a PSB will be confirmed by the
PSB’s LED and in the selected component’s Product Group on the 903i
Comparator.
Pressing an alternate component’s PSB will activate the new selection and
deactivate the previous selection. To turn a selected component OFF, simply
press its PSB.
To add a pair of speakers to the current selection, Long-press the PSB for the
set of speakers you wish to add. To deselect one of the multiple pairs
playing, Press its PSB (the maximum number of speaker pairs allowed is
determined at installation).
Troubleshooting
First check that the 903i is connected to a System Bus port (not the 903 port on the 980). There are two common conditions that can cause a system to malfunction:
- Switching Modules that are not properly addressed.
- Buses are improperly connected (system bus, high-level bus, low-level bus).
Either of these conditions can cause the system to be “confused” since the 903i would not be able to communicate with all of the switching modules. All of the module addresses should have been set and all the bus networks connected by the installer. If this was not properly done or if any module addresses have been changed, or new modules added to the system since the original installation, verify all the address settings and check all the bus connections in your system before further troubleshooting. Refer to the original Access System Installation Manual for instructions on module addresses and bus connections.
If you have any difficulties during the installation, don’t hesitate to call us for assistance! We’re open Monday through Friday from 8:30 AM until 5:00 PM, Eastern Time. Also check our website for template diagrams and tips: audioauthority.com/access_tips. How to Update Firmware Download the latest firmware and watch this step-by-step process (below) shown in a short video here: www.audioauthority.com/903i- update
- Enter the menu and touch Admin
- Instead of your usual code, enter 8675309
- Touch the icon at the bottom of the screen to find the apps
- Touch Apk Installer
- Touch Install
- Insert a USB drive containing the new firmware APK file
- Touch USB Memory
- Touch USB_DISK2
- Touch udisk0, then touch the APK file on the right
The 903i reboots and is ready for use.
audioauthority.com/access_tips
2048 Mercer Road, Lexington, Kentucky 40511-1071 800-322-8346 · 859-233-4599 · Fax: 859-233-4510 www.audioauthority.com · support@audioauthority.com
752-710 v. 1.6.3 Rev B 20230905
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>