SONOFF SNZB-06P Zigbee Human Presence Sensor User Manual

SONOFF SNZB-06P Zigbee Human Presence Sensor

Introduction

SNZB-06P is a human-presence sensor based on 5.8G microwave technology, which realizes the human-presence sensing function by actively detecting ambient motion and  human breath. It effectively avoids the embarrassing scene where the light automatically off when people are on the spot, making your home life smarter.

Microwave radar

Presence detection

Light sensing

Intelligent linkage

The functional characteristics depend on the functionality of Zigbee gateway.
The equipment is only suitable for mounting at heights ≤ 2 m.

① Human presence sensor
② Magnetic base
③ Button
④ LED indicator (Red)
⑤ Power input interface （Type-C）

Instruction of LED indicator status

to enter pairing mode
Keep on for 3s and then keep off| Paired successfully
Exit flashing slowly and keep off| Distribution failure/timeout
Flash once quickly| Not added to the gateway, and short press the button
Flash twice quickly| Added to the gateway and online, and short press the button
Flash slowly for 30 seconds| Abnormal communication

Specification

Download the eWeLink App & Add SONOFF Zigbee gateway.

Please download the “eWeLink” App from Google Play Store or Apple App Store.

Scan QR Code to Add Device

1. Power on the device
   

2. Enter“scan QR code”mode
   

3. Scan the QR code on the device
   

4. Select“Add Device”
   

5. Long press the button for 5 seconds
   

6. The LED indicator flashes slowly for 180s
   

7. Select Zigbee gateway
   

8. Wait until the addition is done
   

Matched gateways

SONOFF ZBBridge, ZBBridge-P, NSPanel PRO, AIBridge, ZBDongel-P，ZBDongel-E Third-party compatible gateway models:
Amazon Gateway Model: Echo Plus 2nd, Echo Show 2nd Other gateways supporting ZigBee3.0 wireless protocol. Detailed information is in accordance with the final product.
*Displays as a human motion sensor under some gateways.

Effective Communication Distance Verification

Install the device in the desired place, then press the Pairing button on the device. The LED indicator flashes twice means the device and the device under the same Zigbee network (the router device or hub) are in the effective communication distance.

Installation

1. Place on the desktop
   

2.  Attached to the metal surface with the magnetic base|
   

3.  Stick to the wall with 3M adhesive of the base
   

4.  Base screws fixed to the wall
   

Detection zone

The radar’s radial detection distance is approximately 4 meters.

Cautions

1. Keep off moving objects including such as curtains, greenery, fans and pets during installation to avoid the device’s misjudgment that there are persons nearby.
2. Non-metallic materials including such as glass, plastic, ceramics and plank can be pierced through.
3. Multiple sensors should be installed in the same direction or back-to-back, avoiding front-to-front irradiation, and each sensor should be more than 1.5 meter away fromothers.

FCC Warning

FCC compliance statement

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
2.  This device may not cause harmful interference, and
3.  This device must accept any interference received, including interference that may cause  undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with  the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Notice

ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES‐003(B).
This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

ISED Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

SAR Warning

Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

WEEE Warning

WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment,  appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

EU Declaration of Conformity

Hereby, Shenzhen Sonoff Technologies Co., Ltd declares that the radio equipment type SNZB06P is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

https://sonoff.tech/compliance/

For CE frequency

Zigbee:2405-2480MHz
FMCW:5725-5875MHz
RF Output Power:
Zigbee:≤10dBm
FMCW:≤10dBm

RACCOLTA DIFFERENZIATA

Verifica le disposizioni del tuo Comune.
Separa le componenti e conferiscile in modo corretto.

CUSTOMER SUPPORT

Manufacturer: Shenzhen Sonoff Technologies Co., Ltd.
Address: 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
ZIP code: 518000 Service email: support@itead.cc
Website: sonoff.tech Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>