legrand WNREZK10WH 15 Ampere 3 Way and Single Pole Smart Rocker Switch Kit Installation Guide

WNREZK10WH 15 Ampere 3 Way and
Single Pole Smart Rocker Switch Kit
Installation Guide

WNREZK10WH 15 Ampere 3 Way and Single Pole Smart Rocker Switch Kit

No: 341381 5/23

WNRL10 radiant ® Smart Switch with Netatmo Incandescent, Halogen: 1800W;
Resistive: 120VAC, 60Hz, 15A; Standard + Electronic Ballast: 15A; Motor: 1/2 HP WNRL23 radiant® Wireless Smart Switch with Netatmo

Installation Instructions

WNRL10 radiant ® Smart Switch WNRL23 radiant ® Wireless Smart Switch with Netatmo

REGULATORY INFORMATION
FCC NOTICE: This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following  measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 10 mm between the transmitter’s radiating  structure(s) and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.
Contains FCC ID : 2AU5D982057
IC NOTICE : This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 10 mm to the human body. Note: Any changes or modifications to this device  that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.
IC: 25764-982057
HVIN: 982057
IC: 25764-WNZED
HVIN: WNRL23
OPTIONAL — APP CONTROL
This kit contains a WNRL10 (wired) and a WNRL23 (battery) device that are paired together at the factory. Additionally, these devices are equipped with enhanced functionality enabled through the Legrand Home+Control app.
Adding app control will result in loss of the factory pairing and will require devices be re-paired using the app. To add app control to this device, you will need to purchase a Legrand Gateway. For more information, visit www.legrand.us/addappcontrol
WARNING: Do not press the EZ button on devices unless you are adding app control. Pressing the EZ button will undo factory pairing.

WNRL10 SWITCH

BEFORE YOU START
Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.
Warning: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
Caution: To reduce the risk of injury and/or overheating and damage to other equipment:

• For dry, indoor use only.
• Do not use to power medical equipment – not suitable as a disconnecting means.
• Do not use with loads exceeding the device load rating.
• Connect the smart switch to a 120 VAC, 60 Hz power source ONLY.
• Always use copper wire to install the smart switch & follow all applicable local & national electrical codes.

WHAT YOU NEED
Required:

• Phillips-head screwdriver
• Flat blade screwdriver

You May Also Need:
Voltage tester, pliers, wire cutter, wire stripper, electrical tape, flashlight, wiring leads (included), and wire nuts (included).

INSTALLATION

1. Turn off power to device at circuit breaker
   Flip existing light switch multiple times to confirm power is off.
   NOTE: Ensure power is off to all devices in electrical box.

2. Remove existing device Check for the following wires:
   a. HOT or LINE: Receives power from the circuit box.
   Referred to as “hot” for the purpose of this guide.
   Do not touch or let “hot” wire contact other wires. b. LOAD: Directs power to your light(s).
   c. NEUTRAL: Creates a path to return current to the power source when the device is off. Required for your switch installation.
   d. GROUND: Provides a safe path for electricity in the even of a short circuit.

3. Wire Smart Switch
   Use the wire nuts provided to secure the wires together.
   a. Connect the WHITE neutral wire on the switch to the neutral wires in the box, using the red wire nut.
   b. Connect the LOAD wire on the switch to the load wire(s) in the box.
   c. Connect the HOT wire on the switch to the hot wire(s) in the box.
   d. Connect the GREEN ground wire on the switch to the ground wire(s) in the box.

4. Secure Smart Switch
   a. Fold the wires into electrical box, taking care not to pinch a wire.
   b. Use included screws to secure smart switch to electrical box. Do not fully tighten the screws.

5. Test The Smart Switch
   NOTE: See Getting to Know Your Switch section for feature details. Turn the power back on at the circuit breaker, press switch to turn light on/off.
   TROUBLESHOOTING TIP: If the device is not powering check wiring to determine if you have reversed the “HOT” and “LOAD” wiring.

6. Attach Wall Plate
   a. Use the sub-plate screws (provided) to secure the sub-plate to the smart switch.
   b. Tighten device screws to secure smart switch to the electrical box.
   c. Angle the UP end of the wall plate over the top edge of the sub-plate. Push the crewless wall plate down and in until it “snaps” into place over the sub- plate.
   NOTE: To remove the wall plate, place the tip of a flat blade screwdriver into the slot under the wall plate and twist gently.

For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: https://www.legrand.us/p/wnrezk10wh

GETTING TO KNOW YOUR SWITCH

of paddle to turn light off.
2| LED Locator Light| Lit when light is off.
3| EZ Button| Used to factory reset (CAUTION:
PRESSING THIS BUTTON WILL UNPAIR THE BATTERY DEVICE FROM THIS DEVICE AND THE BAT- TERY  DEVICE WILL NO LONGER CONTROL THIS SWITCH)..

SPECIFICATIONS

WNRL23 WIRELESS SWITCH

BEFORE YOU START

Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.
WARNING: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
CAUTION: To reduce the risk of injury and/or overheating and damage to other equipment:

• For dry, indoor use only.
• Do not use to power medical equipment – not suitable as a disconnecting means.

WHAT YOU NEED
Required:

• Phillips-head screwdriver
• Flat blade screwdriver

You May Also Need:
Voltage tester, pliers, wire cutter, wire stripper, electrical tape, and wire nut.

INSTALLATION

1. Choose a place to install device (A, B, or C below)
   This device can be installed on a flat wall surface or in any standard U.S. electrical wall box. It may also be installed over the wall next to a standard U.S. electrical wall box, if used  with a multi-gang Legrand radiant wall plate, catalog number beginning with RWP26-XXX.
   This device MUST BE INSTALLED WITHIN 30 FEET of WNRL10 Smart Switch.
   A) INSTALLATION (on a wall surface)

2. Use provided double sided stickers to install on a tiled or other smooth surface. Markings on the back of the device indicate location for the stickers.

3. Use provided mounting screws to install on dry wall or uneven surface where the sticker may not work. Do not remove label or pull out ground wire as device may not sit flush.
   B) INSTALLATION (in an electrical box)
   2. Turn off power to the box at circuit breaker.
   Note: Ensure power is off to all devices in the electrical box. Remove old device from box. Install wire nuts to terminate all the exposed wires that were previously connected to the old device. Ensure complete electrical insulation by securing the wire nuts making sure no bare wire is exposed.

3. Install and secure the device
a. Fold the wires into the electrical box, taking care not to pinch a wire.
b. Remove label on back of the device to expose ground wire and connect it to the box ground.
c. Use included mounting screws to secure the device to the electrical box.

C) INSTALLATION (NEXT TO AN ELECTRICAL BOX)
2. Break off the tabs on device
Break off the tabs at the top and bottom of the device using pliers as shown in image.
Mark the location of the device on the wall surface to the left or right of existing device(s) installed in the electrical box by visually aligning it with existing device(s)
3. Install and secure the device
a. Use double sided stickers to install on tiled or any other smooth surface next to the electrical box.
b. Use provided mounting screws if the surface next the electrical box is dry wall or uneven surface where the sticker may not work.
4. Attach Wall Plate
a. Install the multi-gang subframe using sub-frame screws provided with the radiant wall plate.
b. Snap-on the radiant wall plate.
If installing with a non-radiant wall plate, skip steps 4a and 4b above and use screws provided with the other wall plate to secure this device.
For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: www.legrand.us/p/wnrezk10wh

GETTING TO KNOW YOUR BATTERY POWERED SWITCH

the paddle to turn light off.
2| LED Indicator Light| Low battery – switch LED will flash red once when paddle is pressed indicating low battery
3| Battery| Lithium ion CR2032

Remove Switch Cover

Legrand reserves the right to change specifications without notice.

LIMITED ONE YEAR WARRANTY
Legrand will remedy any defect in workmanship or material in Legrand products which may develop under proper and normal use within ONE year from date of purchase by a consumer:
(1) by repair or replacement, or, at Legrand’s option, (2) by return of an amount equal to consumer’s purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR  FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Legrand does not include or cover cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR  CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED  HEREBY. (Some states do not allow disclaimers or exclusion or limitation of incidental or consequential damages, so the above disclaimer and limitation or exclusion may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING  WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE ONE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on how long  an implied warranty lasts, so the above limitation may not apply to you.)
To ensure safety, all repairs to Legrand products must be made by Legrand, or under its specific direction. Procedure to obtain performance of any warranty obligation is as follows: (1) Contact Legrand, Syracuse, New York 13221, for instructions concerning return or repair; (2) return the product to Legrand, postage paid, with your name and address and a written description of the installation or use of the Legrand product, and the observed defects or failure to  operate, or other claimed basis for dissatisfaction. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

For covering patents, see www.legrand.us/patents
No: 341381 5/23
© Copyright 2023 Legrand All Rights Reserved.
Questions? We’re here to help.
Phone: 1-877-833-3303 8:00 a.m. to 8:00 p.m. EST (M-F)
Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the chat icon to open a dialogue box)800.223.4185
1.877.BY.LEGRAND
www.legrand.us
www.legrand.ca

References

• Adding App Control with the radiant Easy Kits | Legrand
• radiant Easy 3-Way Switch Kit │ Legrand
• Adding App Control with the radiant Easy Kits | Legrand
• radiant Easy 3-Way Switch Kit │ Legrand
• Smart Lighting from the radiant Collection ⎸Legrand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>