BUSHWACKER 20088-02 Fender Flares

Product Information

The product is a set of fender flares manufactured by Bushwacker. The fender flares are designed to enhance the appearance of the vehicle and provide protection to the vehicle’s fenders. The flares are made of durable materials and come with all the necessary hardware for installation. The product is compatible with various models of vehicles, and fitment information can be found on the Bushwacker website.

Product Usage Instructions

1. Fit: Before installation, verify the fit of the flares to the vehicle. Some filing, sanding, or cutting may be necessary to ensure a proper fit.
2. Performance: If using larger tires, be aware that it may increase the area required to turn the vehicle. Certain tire/rim combinations may require lowering bump stops and/or installing steering stops to prevent tire from contacting the flare.
3. Exhaust System: Modifications may be necessary to maintain a minimum 4-inch clearance between the flares and exhaust pipes. It is important to ensure that exhaust gases do not vent directly onto the flares.
4. Metal Protection: Before installing the flares, treat all exposed fasteners and bare metal with rust-resistant paint. After completing the flare attachments, spray the inner fender wells with undercoating.
5. Decals: The flares may interfere with existing decals on the vehicle. If desired, remove decals prior to installing the flares.
6. Care & Cleaning: The Bushwacker fender flares are built to last. Any detergent used to wash the vehicle is sufficient to clean the flare. Avoid using harsh abrasive detergents.
7. Tools for Easy Installation: The hardware kit includes various components for installation. Refer to the included component list for details.
8. Edge Trim Installation (if required): If the flares do not already have edge trim installed, follow the provided instructions for applying the edge trim to the top edge of the flare.
9. Rear Flare Installation Procedures (Passenger’s Side):
10. Remove the factory fastener from the rear of the wheel well and thoroughly clean the vehicle sheet metal and inner flange.
11. Hold the flare to the vehicle and mark five flare hole locations with a grease pencil.
12. Wrap a foam tab around the wheel well sheet metal, centered over each of the upper four marks. Place a mylar tab at the mark made on the lower front of the wheel well.
13. Install a clip over each of the four tabs placed over the upper four marks. Install a supplied S clip over the mylar tab installed at the lower front of the rear wheel well.
14. While holding the flare to the vehicle, start supplied screws through the four topmost mounting holes in the flare and into the clips installed in the previous step.

Note: It is important to read and follow all instructions provided in the user manual for proper installation and usage of the fender flares.

STEP 1 – PRIOR TO INSTALLATION

Bushwacker® only approves installing the flares according to these written instructions with the hardware provided.
WARNING: Failure to install according to these instructions will invalidate the warranty. This includes, but is not limited to using alternative installation methods, hardware, or materials. DO NOT USE: Loctite, SuperGlue, or similar products on the hardware or the flares.

• Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure proper fit).

• Painting: (Optional) if paint is desired it must be done prior to installing flares on vehicle. Clean outer surface with a good grade degreaser. DO NOT USE LACQUER THINNER OR  ENAMEL REDUCER AS A DEGREASER. Wipe outer surface thoroughly with a tack rag prior to paint. Application of plastic adhesion promoter for ABS plastic as per your paint system manufacturer’s recommendations is required. Paint flares using a high quality enamel, or polyurethane automotive paint. If painting edge trim (not recommended), use a flex additive.

• Performance: Using larger Tires may increase the area required to turn the vehicle. Some Tire/Rim combinations may require lowering bump stops and or installing steering stops to prevent tire from contacting flare.
  Exhaust System: Modifications may be necessary to maintain a minimum 4” clearance between flares and exhaust pipes. (Exhaust gases should not vent directly onto flares)

• Metal Protection: All exposed fasteners and bare metal should be treated with rust resistant paint BEFORE installing flares. Spray inner fender wells with undercoating AFTER flare attachments have been completed.

• Decals: Flares may interfere with existing decals on vehicle. If you wish, remove decals prior to installation of flares.

• Care & Cleaning: Bushwacker fender flares are built to last; any detergent you use to wash your vehicle is sufficient to clean the flare. Do not use any harsh abrasive detergents.

Ford Extend-A-Fender®

• Ford OE Style®
• DRT Style®
• Fender Flares
• Rear Pair
• Set Part #20088-02

  • 20108-02

  • 20126-02

  • 20148-02

  • 20150-02

• Rev-3 02/14/2022
• For complete fitment info visit : www.bushwacker.com

TOOLS FOR EASY INSTALLATION

• Utility Knife
•  #2 Phillips Driver
• 1/2” Wrench
• Socket Wrench
• 7/32” Socket
• 9/32” Socket
• 10mm Socket
• Grease Pencil

PLEASE READ: Dirt and debris can become lodged between the fender flares and the vehicle’s fenders, causing scratching and paint wear from vibration. Lund International is not responsible for any damage, and the installation of our fender flares is done with the buyer’s understanding that this scratching and paint wear may occur.

LIMITED LIFETIME WARRANTY AGAINST ANY MANUFACTURING DEFECTS

To claim a warranty, you must provide Proof of Purchase.

Included in Hardware Kit

Component List:

If your flares already have the edge trim installed, skip to Rear Flare Installation Step 1.

STEP 2 – EDGE TRIM INSTALLATION

• Peel two to three inches of red vinyl backing away from Edge Trim (GP1-0025) tape. Applying the adhesive side of the edge trim to the inner side of the flare, affix the edge trim to the top edge of the flare (the portion that comes in contact with the vehicle).
• Press edge trim into place along the top edge of the flare in one-foot increments, pulling red vinyl backing free as you continue to work your way around the top edge of the flare. Trim flush with ends of flare.

Rear Flare Installation Procedures (Passenger’s Side):

1. Remove factory fastener from rear of wheel well. Thoroughly clean the vehicle sheet metal and inner flange prior to installation.
2. Hold flare to vehicle and mark five flare hole locations with a grease pencil.
3. Wrap a Foam Tab (MT1-0034) around the wheel well sheet metal, centered over each of the upper four marks made in Step 2. Place a Mylar Tab (MT1-0014) at the mark made on the lower front of the wheel well.
4. Tab locations
5. Install a Clip (CL1-0009) over each of the four Tabs (MT1-0034) placed over the upper 4 marks made in Step 3.
6. Install a supplied “S” clip (CL1-0005) over the mylar tab installed at the lower front of the rear wheel well.
7. While holding flare to vehicle, start supplied screws (SW1-0058) through the four topmost mounting holes in flare and into the clips installed in Step 5.
8. Start a supplied screw (SW1-0050) through the flare into the clip installed in Step 6. Tighten all screws.
9. Install supplied push retainer (RV1-P0001) into flare and through factory hole at rear of wheel well.
10. Completed rear flare installation.

Edge Trim Tool Procedures:

• Using supplied Edge Trim Tool (ET1-0002), seat edge trim against vehicle by hooking curved end under edge trim at one end of flare. Next, slide around outer edge of flare to the other end.
• Using flat end of supplied Edge Trim Tool (ET1-0002), seat edge trim against flare by inserting straight end between edge trim and flare at one end. Next, slide around entire edge to the other end.

4325 HAMILTON MILL RD.

• BUFORD, GA 30518
• 1-800-234-8920 (USA AND CANADA)
• FAX 800-438-3788

References

• Bushwacker Fender Flares, Armor & Accessories | RealTruck

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>