IP-COM G1116P-16-150W 16 Port Gigabit Desktop Rackmount Switch Installation Guide

IP-COM G1116P-16-150W 16 Port Gigabit Desktop Rackmount Switch

Package contents

• Switch *1
• Pads*4
• Power cord *1
• Screws (G1116P-16-150W: 6, G1124P-24-250W: 8)
• L-shaped bracket *2
• Quick Installation Guide *1

LED Indicator

Set the network mode to the one you need using the network mode switch according to the following description.

Standard Mode (default):
In this mode, the switch functions as a common switch, and all the ports of the switch can communicate with each other.

CCTV Mode:

• In this mode, PoE ports 1-8 have higher priorities over the other ports.
• All the ports of the switch can communicate with each other.
• If multiple IP cameras are connected to the switch, you are recommended to enable this mode and connect special supervision IP cameras to the ports with high priority, the two uplink ports of the switch to upstream devices (such as NVR, router, and so on), to ensure smoother monitoring video playback.
• Ports 15 and 16 of G1116P-16-150W and ports 23 and 24 of G1124P-24-250W are uplink ports.

VLAN Mode:

• In this mode, ports 1 to 14 of G1116P-16-150W are isolated from each other but can communicate with ports 15 and 16 (uplink ports) respectively.
• Ports 1 to 22 of G1124P-24-250W are isolated from each other but can communicate with ports 23 and 24 (uplink ports) respectively.
• The switch can reduce broadcast storms and isolate DHCP broadcasts.

Isolation Mode:

• In this mode, ports 1 to 8 and Ports 9 to 16 of G1116P-16-150W belong to two different VLANs.
• Ports 1 to 12 and Ports 13 to 24 of G1124P-24-250W belong to two different VLANs.
• This mode can be used to isolate supervision networks and wireless networks to make them not interfere with each other.

Connecting Devices

Note

• When the switch works in VLAN mode, the preceding Physical Connection figure is not applicable.
• The switch supports automatic MDI/MDIX. The Ethernet cable connecting the switch to the peer device can be “straight through” Ethernet cable or twisted pair cable
• For safety, do not let the air vents of the switch down.

Technical Specifications

RECYCLING

• This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
• User has the choice to give their product to a competent recycling organization or to the retailer when they buy new electrical or electronic equipment.

CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

WARNING:
The mains plug is used as a disconnect device, the disconnect device shall remain readily operable.

NOTE:

1. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
2. To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. This device complies with Part 15 of the FCC Rules. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

1. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
2. To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.

Copyright
© 2018 IP-COM Networks Co., Ltd. All rights reserved.

This documentation (including pictures, images, product specifications, etc.) is for reference only. To improve internal design, operational function, and/or reliability, IP-COM reserves the right to make changes to the products described in this document without the obligation to notify any person or organization of such revisions or changes.

Technical Support

• Address: Room 101, Unit A, First Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052
• Tel: (86755) 2765 3089
• Email: info@ip-com.com.cn.
• Website: http://www.ip-com.com.cn.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>