PondMAX EVO II Series Skimmer and Water Feature Pump Instruction Manual

: June 13, 2024
: PondMAX

PondMAX EVO II Series Skimmer and Water Feature Pump

$PondMAX-EVO-II-Series-Skimmer-and-Water-Feature-Pump-fig- $2$$

Product Information

The PondMAX EVOII Skimmer & Water Feature Pumps are high-quality pumps designed for water features. They are part of the PondMAX product range, which includes pond filtration, outdoor/underwater lighting, water treatments, and general accessories.

Technical Specifications:

Description| Maximum Water Flow (GPH)| Maximum Head (FT)| Volts (V) & Frequency (HZ)
---|---|---|---
EV700| 700| 10| 115 / 60
EV900| 900| 14| 115 / 60
EV1200| 1200| 15.5| 115 / 60
EV1800| 1800| 16| 115 / 60
EV2400| 2400| 20| 115 / 60
EV3000| 3000| 21| 115 / 60
EV3600| 3600| 22| 115 / 60

For more information, please visit the PondMAX website.

Design Highlights:

The pumps are designed to prevent motor burnout.
They are suitable for installation in various applications.
Intelligent system adjusts motor speed based on water flow.
In case of rotor jam, the pump will activate a low state to prevent motor burnout.

Benefits:

Prevents sudden jolting during startup.
Avoids motor burnout due to lack of water flow.

Product Usage Instructions

Important Safeguards:

This equipment should not be used by persons under 16 years of age or those unfamiliar with the instructions.
Prevent water from traveling down the cable and onto the plug or power supply.
If the plug gets wet, do not unplug the cable. Disconnect the circuit breaker and consult an electrician.

Product Specific Safeguards

Ensure the pump is not blocked to avoid overheating and burnout.
Select a pump with sufficient flow rate for the required job.

Installation:

Two different front filter screens are provided for convenience:

Front filter screen with built-in flow control: Use this in clean water features to adjust water flow if it is too fast for the installation.
Front filter screen with sponge filter insert: Connect this to the front of the pump when using a fountain kit to strain out larger particles and reduce the frequency of cleaning the fountain nozzles.

WELCOME TO THE WORLD OF PONDMAX™. YOU MADE THE RIGHT CHOICE INVESTING IN THIS QUALITY PRODUCT. THANK YOU AND ENJOY
BEFORE USING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS CAREFULLY AND BECOME FAMILIAR WITH THE UNIT. PLEASE KEEP THESE INSTRUCTIONS IN A SAFEPLACE FOR FUTURE REFERENCE

TECHNICAL SPECIFICATIONS

DESCRIPTION

| EV700| EV900| EV1200
---|---|---|---
MAXIMUM WATER FLOW(GPH)| 700| 900| 1200
MAXIMUM HEAD (FT)| 10| 14| 15.5
POWER CONSUMPTION* (W)| 23| 32| 45
VOLTS (V)| 115| 115| 115
FREQUENCY (HZ) AC| 60| 60| 60
FRONT FILTER CAGE: FLOW ADJUSTER| Yes| Yes| Yes
FRONT FILTER CAGE: SPONGE PRE-FILTER INC.| Yes| Yes| Yes
INLET Ø THREAD (INCH)| 1| 1| 1
OUTLET Ø THREAD (INCH)| 1| 1| 1
CABLE LENGTH (FT)| 32| 32| 32
RECOMMENDED TUBING SIZE (INCH) ID| 1| 1| 1
RECOMMENDED FOUNTAIN KIT**| #30 Jet Kit| #40 Jet Kit| #40 Jet Kit

SUBJECT TO VARIATION ACCORDING TO LOAD
SOLD SEPARATELY

OTHER MODELS AVAILABLE IN THE EVOII RANGE

| EV1800| EV2400| EV3000| EV3600
---|---|---|---|---
MAXIMUM WATER FLOW(GPH)| 1800| 2400| 3000| 3600
MAXIMUM HEAD (FT)| 16| 20| 21| 22
VOLTS (V) & FREQUENCY (HZ) AC| 115 / 60| 115 / 60| 115 / 60| 115 / 60

DESIGN HIGHLIGHTS

The PondMAX EVOII Skimmer & Water Feature Pumps have been manufactured to provide you with the best quality pumps for your water feature. Visit our website to view our range of pond filtration, outdoor/underwater lighting, water treatments and general accessories.

SMART MAG™ Motor Protection – Provides longevity by preventing motor burnout.
Energy Efficient – Exceptionally low power consumption to high-head height / high-volume flow conversion.
Threaded Inlet & Outlet – Suitable for submersible or external operation and can adapt to different fittings provided.
Can Be Installed Vertical or Horizontal – Provides flexibility for installation in many different applications.
Open Vane Impeller Design – Handles large particles and resists clogging.
Adjustable Flow Control – Meet the demands of your application and

BENEFITS INCLUDE

PondMax Skimmer & Water Feature pumps are suitable for use in many different applications including skimmers, water features, aquatic systems and hydroponics. Your pump can be used in either submersible or external applications.
Skimmer & Water Feature pumps are a magnetically driven pump, therefore they cannot suck from a water level that is below the inlet level when used externally.
Your pump has a single moving part (an impeller) enabling easy cleaning and maintenance.
The models EV700 – EV3600 Pumps have SMART MAGTM motor protection, which analyses the speed and torque of the motor.
SMART MAGTM intelligent circuitry also provides a soft start for the pump on startup and helps to avoid any sudden jolting. The intelligent system will change the motor speed to the ﬂow of water in the given circumstances.
Also if the Impeller gets jammed or stops, the circuitry will sense the state and cut the power automatically for 3 seconds and then power up again. This procedure will repeat 3 times. If the rotor is still jammed, it will activate a prolonged low state, till the pump is turned off, and adequate maintenance is carried out. Thus motor burnout, due to electrical heat, through lack of water ﬂow through the motor.
The motor and electrical components are totally encapsulated in epoxy resin, ensuring safe operation under water.
The pump has a robust bearing and shaft design so no Oil/grease lubrication is required.
Skimmer & Water Feature pumps rely on water to cool and lubricate it. Therefore no harmful oil or grease lubrication is required.
PondMAX Skimmer & Water Feature Pumps are continuous rated therefore are designed to operate 24/7.
An optional fountain kit can be purchased and ﬁtted to the models EV700 – EV1 00 pumps. These models include an optional sponge pre-ﬁlter that assists in straining the partials in the water, to assist the fountain nozzles becoming blocked up with debris. See your retailer for options.

IMPORTANT SAFEGUARDS

Correct and safe use of the system requires strict compliance with the safety instructions. For safety reasons, persons less than 16 years of age or persons that are not familiar with these instructions should not use this equipment.

Any damage to the equipment or unmerited operation will bring dangers to the surrounding precincts. f there is any damage of the equipment, it must not to be used. The equipment should be placed out of reach of children.
For your own safety, disconnect from the power supply before any maintenance. Always unplug the pump from the power supply when not in use. Never pull the cable to disconnect the plug from the power supply – grasp the plug and pull to disconnect. If required, have a qualiﬁed electrician install a weatherproof power supply point near to the pond or water-feature (within the cable length of the appliance).
When used in submerged application, be sure the equipment is completely in the water. The depth should not be greater than 6.5Ft.
Do not operate the pump if the appliance or any components of the system, such as the power cable, has been damaged. Check appliance for defects regularly.
For safety, plug the pump into an electrical outlet with a (GCFI) Ground Fault Circuit Interrupter.
To avoid an electric shock, do not attach the plug to the power supply socket with wet hands. The drip loop method should be used to prevent water from traveling down the cable and onto the plug or power supply.
If the plug does get wet, do not unplug the cable. Disconnect the circuit breaker that supplies power to the power supply point. Then unplug and examine the plug and power supply point for presence of water. If the power point has become wet, you should consult an electrician before using the power point again.
Do not install or store the appliance where it will be exposed to extreme hot or cold temperatures. Do not use in water above 95°C.
Do not cut the cable as this will result in voiding your warranty.
Care should be taken to arrange the power cable so that it cannot be accidentally tripped over or pulled.
Do not attempt to repair the electrical appliance yourself. Return to an authorized service center or place of purchase if a fault occurs, (regular maintenance is not considered repair and is required by user).

PRODUCT SPECIFIC SAFEGUARDS

Do not operate the pump without water in your plumbing at any time, permanent damage may occur.
When used in submerged application, be sure the equipment is completely in the water. The depth should not be greater than 6.5Ft. If used externally, the pump must have adequate ﬂooded suction at all times.
The pump is designed to be used inside skimmers, directly in a pond or in any other fresh water features.
The pump should only be used in clean water. Do not use the pump in, or with, any chemicals such as a solvent or gasoline.
The PondMAX Skimmer & Water Feature Pumps are cooled by water ﬂowing through the inside of the motor body. If the pump ﬂow becomes restricted it will overheat and could cause permanent damage. Large tubing size is strongly recommended to deliver adequate water ﬂow to cool the pump.
The pump needs to be cleaned regularly to prevent the pump becoming blocked, thus causing the pump to overheat and burn out. This is not a event. It is strongly recommended not to select a pump that is too small for the job required. The ﬂow rate through the pump needs to be enough so that a half of the rated max ﬂow is kept running at all times.

INSTALLATION

For your convenience we have provided two different front ﬁlter . One has a built in ﬂow control, that can be used to adjust the water ﬂow if the ﬂow is too fast for a particular installation. It is suggested that this speciﬁc front ﬁlter screen be used in clean water features.
The other Front Filter Screen contains a sponge ﬁlter insert. This ﬁlter is to be connected to the front of the pump to strain out the larger particles when using a fountain kit. This reduces the frequency of having to cleaning of the fountain nozzles as often. If using an optional fountain kit, select the ﬁlter cage with the sponge insert.

FOUNTAIN KIT SETUP GUIDE

A basic plastic fountain kit is not recommended for pumps that have ﬂow over 1500 GPH. It’s better to use commercial fountain nozzles for higher ﬂow. See your dealer for examples.
For Pumps, from 250 GPH to 1200 GPH, there are a number of optional fountain kits readily available. PondMAX has three readily available. For various suggestions of the correct model and fountain type selection see the speciﬁcation table on page (page 2).
For the purpose of these guidelines, a PondMAX #30 Jet kit has been selected. The installation principle will be similar for the other types.
NOTE : PondMAX #30 Jet kit has been selected as a sample. Fountain kit NOT included with pump. Offered seperatefy. $PondMAX-EVO-II-Series-Skimmer- and-Water-Feature-Pump-fig- $5$$

Using the 1” to ½” threaded Reducing Nipple (1), attach onto the Male Threaded outlet of the pump. Now secure the Dual-Control T Piece (2) onto threaded reducing nipple. Now on the top of the Dual-Control T Piece (2), connect the Threaded Reducing
Adaptor (4) on. Now extend Telescopic Riser with Threaded Locking Nut (10) to the desired height, then secure onto the top (1” thread) of the Threaded Reducing with the threaded locking nut provided. Align Telescopic Riser with Threaded Locking Nut (10) vertically.
Select the desired nozzle, (7) (8) or (9), and screw into the Fountain Nozzle Threaded Mount. (6) Then attach the Fountain Nozzle Threaded Mount to the Telescopic Riser with Threaded Locking Nut (10).
Locate the Stepped Hosetail (5). Attach this to the side outlet of the Dual-Control T Piece to facilitate an optional accessory, for example; a small waterfall or spitter. Now, utilizing the two different Flow-Adjuster knobs (3), on either side of the T-Piece, you can vary the flow to the fountain head or the optional small waterfall/spitter outlet separately.
Feel free to close off the side outlet of the Dual-Control T Piece, if it is not required. However if it is required, connect tubing to the Hosetail provided and direct the hose to your desired location.
Place the pump in desired location; ensure the pump is on a stable surface that is free of sludge, sand and other debris. Position the device in the pond horizontally, on a solid base, in such a way that it is fully covered with water and ensure that the pump is located, at a depth, in the water, which will not allow it to suck air from the surface. This is known as cavitation. Cavitation is a cause of premature impeller wear.
The fountain nozzle should now be protruding out of the water. Push the plug into the power supply outlet to switch on. Use the power supply switch for turning the unit on and off.

FOR MODELS:

22EV125 – EV700
22EV155 – EV900
22EV175 – EV1200

INSTALLATION PLUMBING GUIDE

applications, use the Hosetail. If used externally, use the (2) Coupling Fittings provided in the ﬁttings pack.

SUBMERSIBLE USE
When used inside a pond skimmer / water feature enviroment, follow proceedure as outlined below.

For best results, use the tubing size recommended in the Technical Speciﬁcation table. Depending on the pump size and your tubing size, select the Hosetail required for and evaluate which step on the Hosetail will be used. If you are using 1” hose and you are connecting it to the 3/4”, 1”, 1-1/4”, 1-1/2” Hosetail supplied, remember to saw
ff the smaller size connection (I.E.: 3/4” step). Otherwise it will create a unnecessary restriction in the plumbing system.
Select the 1-1/2” x 1” Reducer Bushing Fitting and thread onto the outlet of the pump (top). To seal , the use of thread seal tape may be ( at your local dealer).
The ﬁttings pack includes a red washer designed for the locking nut on the Hosetail. Place a washer ﬁrmly in the locking nut on the Hosetail ﬁtting. Now thread the locking nut of the Hosetail onto the 1-1/2” x 1” Reducer Bushing Fitting on the pump. Fasten ﬁrmly but do not over tighten.
Now connect the tubing to the Hosetail. Remember to use Stainless Steel Hose Clamps to fasten the hose on to the Hosetail barbs. This is to ensure that the pipe does not blow off at a later time or leak at this point in the plumbing system.
Direct the hose to your desired location.

EXTERNAL USE

When installed outside the pond enviroment, follow proceedure as outlined below.

For best results in external applications, the pump must have adequate ﬂooded suction at all times (installed outside pond, below elevation of the surface of water). Also reference the tubing size recommended in the Technical Speciﬁcation table to make sure the new or existing plumbing conﬁguration is sized correctly.
In external applications it is necessary to remove the Front Filter Screen of the pump to expose the threaded inlet. Do this by removing the Base Plate of pump (see “Cleaning Instructions” Section) and then turn Front Filter Screen counterclockwise, t hen pull away from Pump Motor Body. NOTE: You will not need either of the Front Filter Screens in an external application, so feel free to keep with this instruction manual or discard.
The ﬁttings pack includes (2) 1” x 1” female Coupling Fittings, which are meant to ﬁt directly onto both the threaded inlet and outlet on pump.
Now thread a coupling onto both the inlet and outlet of the pump. Fasten ﬁrmly but do not over tighten. To seal , the use of thread seal tape may be required ( at your local dealer).
Make sure that the suction line (inlet side of plumbing) has a suction screen or leaf strainer to catch large debris that could potentially harm pump (ask your local dealer for further information).
Now the pump is ready to be connected to new or existing plumbing conﬁguration. Extra ﬁttings and adapters may be required ( available at your local dealer), based on the specific application

CLEANING INSTRUCTIONS

Begin by ensuring that the mains power supply is disconnected before attempting any maintenance of the unit or the water body. Remove the unit from the water. If your unit is connected to a sponge filter, the front screen and sponge will clog up over time. Please clean regularly (at least once a month) to ensure strong water flow. Failure to maintain the unit could result in a burnt out motor and other damage

All PondMAX Skimmer & Water Feature Pumps are water cooled. If pump becomes restricted or blocked, it may overheat and could cause permanent damage.
The motor unit of the pump is encapsulated with epoxy resin and does not need lubrication. Regular inspections, cleaning and maintenance of impeller is necessary to ensure longer life. In the center of the impeller you may notice a small hole opening that protrudes through the ceramic shaft from front to back. It is important that this opening is kept unblocked at all times. This is a cooling channel for the motor.
If using a fountain kit, take off the fountain set first by unscrewing it from the top of the pump. Examine the nozzles to ensure all ports are unblocked. Clean with a suitable brush if necessary
Maintain the filter sponge regularly according to how long it takes for the screen to get clogged up. When the flow starts to be reduced, check and clean if necessary.
To unclip the front filter from the front of the pump, twist the cage in a counterclockwise direction and pull forward. See below for diagram. If available, take out the optional sponge and clean. . It is recommended that this is done in a bucket of pond water to ensure the good bacteria present in the sponge are not killed by the chlorine in tap water. Check for wear and tear on the sponge and replace if necessary
You can help boost the biological function of your filter sponge with a bacterial additive, available from your local dealer

FEATURE PUMPS

$PondMAX-EVO-II-Series-Skimmer-and-Water-Feature-Pump-fig- $3$$

Turn the Front Filter Screen in the direction as indicated by the arrow, then pull away from the Pump Motor Body.
Locate snap-fit release under Base Plate using the arrows above. Using your thumb, apply pressure and unclip Base
Plate until it releases from Pump Motor Body.
Remove Base Plate by pulling away from the pump motor in the direction of the arrow above.
To remove the impeller of the pump, turn the Impeller Cover Housing in a counterclockwise direction as indicated by the arrow above, to the stop position. Then separate the Impeller cover from the Pump Motor Body.
With one hand gripping the Pump Motor Body, secure grip of the other hand tightly on the fins of the Impeller and pull out the Impeller assembly (take care not to break the ceramic shaft.) The black disc behind the fins of Impeller is part of the Impeller assembly. Clean the Impeller with water and vinegar and a suitable brush taking note to remove fine sediment on and around the back end of the Impeller, the small hole through the ceramic shaft and the chamber the
Impeller fits into on the Pump Motor Body. (Always inspect the Impeller and replace the Impeller if it seems necessary.)
Ensure to replace the O’ring as shown above when reinstalling the Impeller. (See the “IMPORTANT NOTES” section below for reassembly instructions)

IMPORTANT NOTES

It is important that this procedure is carried out regularly as the cooling path inside the motor can become clogged. If the impeller assembly becomes worn or damaged it should be replaced (available from your dealer). Failure to do so may cause serious damage to pump. Inspect for signs for wear and tear.
The impeller set is a wearable part.
Once the cleaning and inspection process is completed, reassemble in the reverse manner.
Reinstall the impeller into the motor body.
To place the Impeller O’ring around the black disc successfully, firmly hold the disc with one hand, and using the other hand stretch the O’ring over the disc, positioning it carefully into the groove. Pay attention not to allow the O’ring to roll forward, in-between the black disc and the Pump Motor Body.
With the impeller in the correct position, carefully place the Impeller Cover Housing on, and then rotate clockwise back into position.
If applicable re-insert the internal Sponge back into the filter screen and re-attach to the pump. On other models re-attach the Front Filter Screen.
Now re-attach the Base Plate into position to lock the impeller cover from turning $PondMAX-EVO-II-Series-Skimmer-and-Water-Feature-Pump-fig- $4$$

EXPLODED VIEW

Front Fiter Screen – for Sponge Sponge
Flow Control Knob (EV700 – EV1200 Only)
Front Fiter Screen – with Hole For Flow
Control (EV700 – EV1200 Only)
Not Shown
Blanking Cap for Hole in Front Filter Screen (optional)
1” Coupling Fitting x2 – for nlet & utlet
Impeller Cover Housing
Impeller Assembly
Impeller O’ring
Base Plate with Rubber Feet
Pump Motor Body
1” x 1-1/2” Reducer Bushing Fitting
Washer – for Locking Nut (Red)
3/4”, 1”, 1-1/4” & 1-1/2” Barbed Hosetail with Locking Collar

$PondMAX-EVO-II-Series-Skimmer-and-Water-Feature-Pump-fig- $6$$

NOTE: Parts and features differ from model to model. All images used are for illustrative purposes only. Not all features depicted apply to all models in the range and these are subject to change.

IMPORTANT
These accessories and attachments are recommended for use with your PondMAX product speciﬁed in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use the accessory or attachment for its stated purpose.

SPARE PARTS

PART NO.	DESCRIPTION	EV700	EV900	EV1200

1

| ****

Front Filter Screen – for Sponge

| ****

31EV130

2

| ****

Sponge

3

| ****

Flow Knob – [EV700 – EV1200 Only]

| ****

31EV127

4

| Front Filter Screen – With Hole for Flow Control – [EV700 – EV1200 Only]

Not Shown

| Blanking Cap for Hole in Front Filter Screen (optional)|

5

| ****

1″ Coupling Fitting x 2 – for inlet & outlet

|

6

| ****

Impeller Cover Housing

| ****

31EV126

7

| ****

Impeller Assembly

| ****

31EV125

| ****

31EV155

| ****

31EV175

8

| ****

Impeller O’ring

9

| ****

Base Plate with Rubber Feet

| ****

31EV129

10

| ****

Pump Motor Body

|

11

| ****

1” x 1-1/2” Reducer Bushing Fitting

|

12

| ****

Washer – for Locking Nut (Red)

|

13

| 3/4”, 1”, 1-1/4” & 1-1/2” Barbed Hosetail with Locking Nut|

5, 11, 12, 13

| Complete Kit EV700-EV1200

– Coupling Fitting x2, Reducer Bushing Fittings, Washer (Red) & Barbed Hosetail with Locking Nut

| ****

31EV128

---|---|---

TROUBLESHOOTING

Problem

| ****

Reason

| ****

Solution

---|---|---

WATER PUMP NOT WORKING

| ****

No Power

| ****

Check that the plug is connected and power point turned on.

Filter Screen or Sponge is blocked with sludge.

| ****

Clean the Filter Screen or Sponge.

Impeller is blocked with sludge or lime scale build up.

| ****

Clean the Impeller as per the instructions.

|

Submerse the equipment underwater then plug in. Refill if necessary.

Blocked Impeller chamber or ceramic shaft is broken.

| ****

Clean the Impeller. Check for wear.

Replace if necessary.

WATER PUMP IS NOISY

| ****

Blockage in pump.

| ****

Clear the blockage.

Impeller & Shaft worn out.

| ****

Replace Impeller Assembly.

Impeller broken.

| ****

Replace Impeller Assembly.

Water level in feature is too low.

| ****

Refill feature with water to appropriate height.

Unit inlet is blocked or the water pump outlet is blocked.

| ****

Clear all blockages.

The height to which you are pumping is too high for the given model of pump.

| ****

Select a bigger model.

LIMITED PRODUCT WARRANTY

• CMT Group LLC, a California limited liability company d/b/a PondMAX™ USA (the “Company”) expressly warrants to the original purchaser that,
for two (2) years from the date of sale, the covered product (the “Product”) will be reasonably free of defects in materials and workmanship and that when properly handled, will conform, within accepted tolerance to applicable manufacturing specifications. This Limited Product Warranty (“Limited Warranty”) only applies to the Company’s Products that are used, stored, handled, and installed in the manner recommended by the Company in the Product instruction manual.
• Notwithstanding this Limited Warranty, the customer acknowledges that some parts of the Product are consumable and may need to be replaced as part of ongoing Product maintenance, as recommended in the Product instruction manual, and are therefore not covered by this Limited Warranty.
• The Company will, at its option, repair or replace the Product without charge if the Product fails or does perform as warranted solely due to a manufacturing defect within the warranty period, subject to the exclusions outlined in this Limited Warranty.
• Repair or replacement during this two (2) year warranty shall not include reasonable labor charges necessary to repair or replace the defective Product, shipping costs, and packing and insurance costs. During the entire two (2) year warranty, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the models of the Product that are available at the time of the repair or replacement, and shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. Any repaired or replaced Product shall also remain subject to the original two (2) year warranty from the date of the original sale, and any repair or replacement shall not extend the original warranty period in any manner or start a new warranty period.
• You may obtain coverage under this Limited Warranty by providing the Company with proof of original purchase. For service under this Limited Warranty, you must first contact the seller, distributor, retailer, or dealer from whom you purchased the Product and provide the following: copy of the original receipt, your name and address, a description of the Product (including the serial number/date code set forth on the Product), and the nature of the defect. To expedite any warranty claims and processing, please submit to us the product registration card included with your purchased Product promptly after your purchase.
• All warranty repairs must be performed by the Company, or a Company authorized third-party. Any repairs performed by you or an unauthorized
third-party will not be compensated by the Company and are not the responsibility of the Company and will void this warranty.
• DISCLAIMER OF WARRANTIES: The company’s Products must be stored, handled, installed, used, and maintained by instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s use guide/care guide are included with the Product and available from the Company at the address listed below. You may also obtain these materials by contacting the Company at
888-868-1185 or on the Company’s website www.pondmax.com.
• This Limited Warranty does not cover defects caused by:
• non-compliance with the Company’s use guides, care guides, and/or instruction manual. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold), incompatibility of fluid used near the Product, or misuse;
• improper storage, installation, handling, and/or use of the Product;
• damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
• unreasonable or unintended use of Product;
• products installed with known or visible manufacturing defects at the time of installation;
• minor conditions such as stains, scratches, etc.
• Any information or suggestion by the Company concerning the Products concerning applications, specifications, or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information concerning the Products for your specific application.
• THE WARRANTIES OUTLINED IN THIS LIMITED WARRANTY ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THE PRODUCT. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES CONCERNING THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY THE COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY THE COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF NON- CONFORMING PRODUCTS. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.
• LIMITATION OF LIABILITY: No claim by the buyer/owner of any kind, including claims for indemnification, shall be greater in amount than the purchase price of the Product in respect to which damages are claimed. IN NO EVENT SHALL COMPANY BE LIABLE TO BUYER/OWNER IN TORT, CONTRACT OR OTHERWISE, FOR ANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL, RELIANCE, STATUTORY, SPECIAL, PUNITIVE OR EXEMPLARY DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, LOSS OF USE, LOSS OF TIME, LOSS OF REVENUES, INCONVENIENCE,
LOSS OF BUSINESS OPPORTUNITIES, DAMAGE TO GOODWILL OR REPUTATION, OR LOSS OF DATA, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR SUCH DAMAGES COULD HAVE BEEN REASONABLY FORESEEN, IN CONNECTION WITH, ARISING OUT OF, OR AS A RESULT OF, THE SALE, DELIVERY, SERVICING, USE OR LOSS OF USE OF THE PRODUCT SOLD HEREUNDER, OR FOR ANY LIABILITY OF BUYER TO ANY THIRD PARTY WITH RESPECT THERETO.
• All provisions of this Limited Warranty are severable and if any provision shall be deemed invalid, the remaining provisions shall remain in full force and effect.
• Please consult your retailer for quality original Company replacement parts.
• Visit www.pondmax.com for your nearest dealer.