SKYLIGHT FS Hyperspot WIFI F Instruction Manual

SKYLIGHT FS Hyperspot WIFI F

Product Information

The SKYLIGHT HYPERSPOT series lamps are designed for use in aquariums of different dimensions. They come with a hanging suspension kit for easy installation. The lamps have different power ratings, luminous flux, beam angles, and color temperatures, as shown in Table 1.

• The lamps operate on a voltage of 12 V DC and require different current ratings depending on the model. They can be controlled via Wi-Fi with a frequency of 2.4 GHz and support WPA2 security standards. The minimum required operating system versions for controlling the lamps are Android 10 or iOS 15.

• When cleaning the lamps, it is important to use a soft cloth and avoid using any chemicals. Do not clean the lamp while it is turned on. All cables should be connected according to the provided diagram before connecting the setup to the main network.

Compatible power adapters for each model are listed below:

• HYPERSPOT FS: ESPE-9012
• HYPERSPOT FM: ESPE-12012
• HYPERSPOT FL: MW-GST160A12-R7B or other power supplies with identical parameters

It is important to use the appropriate power supply to avoid damage to the lamp or power supply itself.

Product Usage Instructions

Installation:

1. Hang the Hyperspot lamp at least 15 cm above the water surface using the provided hanging suspension kit. Refer to the diagram for the position of the mounting holes.
2. Ensure that all cables are properly connected as shown in the provided diagram before connecting the setup to the mains network.

General Instructions:

• When cleaning the lamp, use a soft cloth and avoid using chemicals. Do not clean the lamp while it is turned on.

Repairs and Utilization:

• If the lamp is damaged, do not attempt to repair it yourself. Contact your supplier for information about lamp service.
• The LED module in the lamp is not intended to be replaced by unqualified personnel. LED modules can be obtained from your supplier.
• Dispose of the product at designated collection points according to the directive 2012/19/UE. Do not dispose of it as unsorted municipal waste.

Specifications

The SKYLIGHT HYPERSPOT series lamps are manufactured in different versions suited for different aquarium dimensions. They come equipped with a hanging suspension kit. Electric ratings of different versions are presented in Table

Android 10 or iOS 15

Table 1.a. HYPERSPOT – specification.

SAFETY INSTRUCTIONS

The product is only intended to be used for aquarium lighting, indoors and at room temperature. Follow the installation instructions. Keep children and pets other than your aquarium animals away from the lamp. Do not use a mechanically damaged device, do not modify the construction.

• Do not switch on the device if any cable(including the power supply)is damaged.
• Only intended to be used with one of the dedicated power supplies*).
• Do not exceed electrical ratings!
• Do not look directly into the light source.
• Turn the lamp on only after it is installed over the aquarium.
• Do not cover the lamp with rugs or blankets.

INSTALLATION INSTRUCTIONS

Hyperspot lamps should be hung a minimum of 15 cm above the water surface. Elements of the hanging suspension kit are shown in Fig ❶.

• Lenght: 1,5 mWeigth: 120 g
• Maximum long-term load: 18kg/175N
• Maximum short-term load: 90kg/885N
• Material: Stainless steel
• Position of the mounting holes for the hanging suspension kit. Fig. ❷

GENERAL INSTRUCTIONS AND HANDLING

• The PMMA glass cover of the LED module should be cleaned using a soft cloth and with no chemicals. Do not clean the lamp when it is turned on.
• All cables should be connected as shown in Fig. ❸ before the setup is connected to mains network.

List of compatible power adapters:

or other power supplies with identical parameters.

CAUTION!:
Using an inappropriate power supply will result in damage to the lamp or power supply itself!

REPAIRS AND UTILIZATION

Do not try to repair a damaged lamp. For information about lamp service contact your supplier. The LED module in this lamp is not intended to be replaced by unqualified personnel. LED modules are available from your supplier, contact them for details. The product cannot be disposed of as unsorted municipal waste. According to the directive 2012/19/UE, the device should be disposed of at designated collection points.

WARRANTY

SKYLIGHT warrants this product to be free of defects in material and workmanship under normal use for 2 years from the date of purchase. The obligation of this warranty is limited to the repair or replacement of defective elements. No claim shall be allowed under this warranty if, in the opinion of SKYLIGHT, this product has been subject to accident or improper usage, including, but not limited to: damage, improper storage, accidental dropping, etc.

Please send the damaged device to your supplier including the power supply and cables, the completed warranty card, and the receipt. The serial number on the device has to be the same as on the warranty card. The obligation of this warranty is limited to the device bought, and no claim shall be allowed under this warranty due to damage or loss of any other objects.

WARRANTY CARD

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>