FEIT Electric PND95CCTNLBLK Single Light Trapezoid Pendant Installation Guide

FEIT Electric PND95CCTNLBLK Single Light Trapezoid Pendant

Safety Information

For your safety, always remember to:

• Tum off the power supply at the fuse or circuit breaker box before you install the fixture.
• Ground the fixture to avoid potential electric shock and to ensure reliable starting.
• Double-check all connections to be sure they are tight and correct.
• Wear rubber soled shoes and work on a sturdy wooden ladder.
• Account for small parts and discard packing material, as these may be hazardous to children.

This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, check your local electrical code or consult a qualified electrician.

• MIN 90° C SUPPLY CONDUCTORS

FCC STATEMENT

• Supplier’s Declaration of Confonnity:   47 CFR § 2.1077 Compliance Information
• Responsible Party : Feit Electric Company  4901 Gregg Road, Pico Rivera, CA 90660, USA
• Unique Identifier : PND95CCTNLBK

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

CAN ICES-005 (B).

• CAUTION: Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
• CAUTION: Consult a certified electrician to ensure correct branch circuit conductor.
• WARNING: RISK OF SHOCK House electric current can cause  painful shock or serious injury unless handled properly.
• CAUTION: RISK OF FIRE. Before installing your lighting  fixture, thoroughly review this installation manual. If you do not have sufficient electrical wiring experience have your fixture installed by a certified electrician. All electrical connections must be in accordance with Local and National Electrical Code (NEC) Standards. Reliable  operating temperature is 0 For more informa­tion including dimmer compatibility visit www.feit.com.
• NOTICE: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a certified electrician.
• Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 1 year from date of purchase. If it tails to do so, please contact the Customer Service Team at www.teit.com .

Pre-Assembly

TOOLS REQUIRED

HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.

Part

AA

| Description

Traoezoid Pendant Liaht

| Quantity

1

---|---|---

• BB
• CC
• DD

|

• Canoov
• 6-lnch Stem
• 12-lnch Stem

|

• 1

• 1

• 1

• EE

• FF

• GG

• HH

|

• 18-lnch Stem
• Crossbar Bracket
• Waao Connector
• Wire Nut

|

• 1

• 1

• 1

• 1

• II

• JJ

|

• Crossbar Bolts
• Junction Box Mounting Screws

|

• 2

• 2

• KK

• LL

|

• Fixture Mounting Finials
• Fixture Mounting Washers

|

• 2

• 2

• MM

• NN

|

• Safety Cable
• Hollow Bolts

|

• 1
• 2

00| Thread Adapter| 1
pp| Thread Couplings| 2

Installation

Turning Off the Power
Turn the power OFF at the switch and fusebox or the circuit breaker and place the wall switch in the off position.

Identifying the Wires
Identify the wiring: (black – line voltage, white – neutral and bare copper – ground). Removing the Crossbar Bracket from the Stem/Canopy
Remove the crossbar bracket (FF) from the fixture (AA) by unscrewing the fixture mounting finials (KK) and mounting washers (LL) from the canopy (BB).

Assembling the Fixture

• Position the 18-inch stem (EE) with the hollow bolt (NN) towards the fixture (AA).
• Run the fixture (AA) wires through the 18- inch stem (EE).
• Position the 12-inch stem (DD) with the pre-attached thread coupling (PP) end towards the 18-inch stem (EE).
• Run the fixture (AA) wires through the 12- inch stem (DD).
• Screw in the 12-inch stem (DD) to the other end of the 18-inch stem (EE).
• Position the 6-inch stem (CC) with the pre-attached thread coupling (PP) end towards the 12-inch stem (DD).
• Run the fixture (AA) wires through the 6- inch stem (CC).
• Screw in the 6-inch stem (CC) to the other end of the 12-inch stem (DD).
• Slide the thread adapter (00) over the assembled stems (CC, DD, EE) with the threads of the thread adapter (00) towards the fixture (AA).
• Screw on the thread adapter (00) to the fixture (AA) to secure the assembled stems (CC, DD, EE) to the fixture (AA).
• Run the fixture (AA) wires at the end of the 6- inch stem (CC) through the canopy (BB).
• Screw in the canopy (BB) to the 6-inch stem (CC).

NOTE: In order to use 6-inch (CC) and U 12-inch (DD) stems without using the 18-inch stem (EE), unscrew the thread coupler (PP) from the desired stem and replace with the hollow bolt (NN). The stem with the hollow bolt (NN) attached must be directly connected to the fixture (Af-0.

Installing the Crossbar Bracket

Secure the crossbar bracket (FF) to the junction box by inserting the two junction box mounting screws (JJ) through the slots on the crossbar bracket (FF) that best align to the junction box.

Connecting the Wires

• To ground the fixture (AA), connect the bare copper ground wire from the supply line and the fixture ground wire to the ground screw on the crossbar bracket (FF) or use a wago connector (GG). Use the wago connector (GG) to connect the white fixture wire to the neutral supply wire and the black fixture wire to the hot supply wire.
• Once the electrical connections have been made to the supply wire, take the black, white, blue, red, green, yellow, wires that were fed through the canopy (BB) and insert them into their matching-colored connectors. To insert the wire securely, take your Philips head screwdriver and press and hold down the tab while you insert the cable. Release the tab once the cable is fully inserted.

Installing the Fixture Canopy

Tuck the wires into the junction box and then lift the fixture (AA) canopy over the crossbar bolts (II) through the fixture canopy holes. Secure the fixture (AA) canopy by inserting the fixture mounting washers (LL) and hand tightening the mounting finials (KK) to the end of the crossbar bolts (II).

NOTE: Ensure wires are not pressing into the U crossbar bracket (FF) or fixture (AA) when tightening the mounting finials (KK) into position.

How to Operate the Single Light Trapezoid Pendant

Operating Instructions:

• Flip wall switch ON after installation to enter Mode 1 (light bulb only).
• Flip wall switch OFF and back ON in less than 5 seconds to enter Mode 2 (light bulb+ LED down light).
• Flip wall switch OFF and back ON again in less than 5 seconds to enter Mode 3 (up light only) .

1. NOTE: Select the desired color temperature for the U downlight located on the top of the canopy via push button (AA). Continue to push the button to cycle through all the available white colors .
2. NOTE: If the unit is turned off for more than 1 O U seconds, the mode will automatically revert to the default mode of Mode 1 (area light only) .
3. NOTE: The downlight will remain the same color U unless the white color selection button that is located on the canopy is pushed to cycle through the different white colors.

(Bulb not included)

Need Help?
Thank you for your purchase.

• Questions, comments or feedback?
  We’d love to hear from you.

• Visit feit.com/help for support or connect with us:

  • @FeitElectric
  • @FeitElectriclnc
  • feitelectriclighting

Please contact feit.com/help for further assistance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>