Himist Moonlight Rabbit Projector Lamp User Manual
- June 4, 2024
- Himist
Table of Contents
Himist Moonlight Rabbit Projector Lamp
Product Introduction
Packing List
Product Buttons Overview
Direction For Use
The procedure of Changing Projection Films
- Remove the projector lampshade in a counterclockwise direction.
- Remove the transparent cylinder in the middle of the Product in a counterclockwise direction.
- Open the transparent lid of the transparent cylinder, then remove the rectangle projection film inside the transparent cylinder and remove the projection film inside the transparent lid.
- Tear off the protective film of the new round and rectangular projection films.
- Roll up the rectangular film and buckle it up.
- Insert the rolled-up rectangular film into the transparent cylinder.
- Put the new round projection into the transparent lid, then close the lid onto the cylinder.
- Insert the transparent cylinder into the base of the Product, then fix it in a clockwise direction.
- Close the projector lampshade and fix it in a clockwise direction.
Switching Between Night Light Mode and Projection Mode
Night Light Mode:
Turn on the power, press the Light Mode Switch Button, and project the
projection pattern on the lampshade as a night light.
Projection Mode:
Turn on the power, press the Light Mode Switch Button and remove the
lampshade of the product, you use it as a projector with projection casted on
the ceiling or wall.
Buttons Instruction
ON/ OFF Button:
Short press to turn on/ off the power, accompanied by a prompt tone; The
power indicator light is solid blue after it is turned on.
Blue tooth Button:
Short press to turn on/ off Bluetooth, accompanied by a prompt sound; After
the Blue tooth is turned on, the prompt sound prompts “Bluetooth Mode”, and
the mobile phone searches for the Blue tooth name “WH-E01” to connect.
Light Mode Switch Button:
A short press of this button will switch the light mode in the following order
(6 light color modes in total):
- Press the 1s t time: only the yellow light is on;
- Press the 2nd time: only white light is on;
- Press the 3r d time: only the blue light is on;
- Press the 4th time: cyclic change mixed two-color lighting;
- Press the 5th time: the yellow, white and blue lights are all on;
- Press the 6th time: Cycle through all lighting modes;
- Press the 7th time: turn off the light.
Rotating Button:
Short press to rotate/stop rotating of the pr objection.
Remote Control Instruction
Note:
- Please pull out the insulating strip at the bottom of the remote control before first use.
- When using the remote control, need sure it points to the infrared receiver of the lamp body and keeps the distance within 2.5 meters.
Charging Instruction
- Please fully charge the Product before first use;
- Please DO NOT dismantle, crash, squeeze the Product, or throw the Product into fire. if there is severe swelling a nd heat, please do not continue to use it; do not place it i n a high temperature environment；
- Please connect the Product to a suitable adapter(5V/1A), power bank, or laptop for power supply;
- The charging time depends on the power supply device;
- Charging indicator: The power indicator lights up in red when charging, and lights up in green when fully charged.
Parameter Information
- Product Name Moonlight Bunny Night Light Projector
- Product Model WH-E04
- Product Size φ131*H158mm
- Product Color White
- Product Specification Bluetooth remote control
- Battery Capacity 1200mAh
- Input 5V 1A
- Rated Power 4.5W MAX
Precautions
- DO NOT disassemble this product by yourself.
- Please DO NOT use the Product in humid and high-temperature environments；
- The light source of the Product cannot be replaced. When the light source expires, please replace the whole Product;
- Please cut off the power when you have not used the Product for a long time. We recommended charging the Product every 30 days to prevent shortening of the life of the lithium battery；
- When the Product is in regular use, do not place it on an inclined surface more significant than 6°;
- Please use an adapter with compliance certification;
- Children under 14 need to use it properly in the custody of adults;
- Use separate collection facilities for electrical appliances that do not dispose of unsorted municipal waste. Contact your local government for information about the collection system. Please don’t discard this electrical appliance in landfills or dumps at will, and hazardous substances can seep into groundwater, enter the food chain, and damage your health and well-being.
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which ca n be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>