fri-jado 20230926 Mounting The Condensation Hood User Manual

: June 13, 2024
: fri-jado

Table of Contents

fri-jado 20230926 Mounting The Condensation Hood
Product Information
Product Usage Instructions
General information
Safety information
Before replacement
- Tools
- Spare parts
Condensation hood overview
Mounting the condensation hood
Read User Manual Online (PDF format)
Download This Manual (PDF format)

fri-jado 20230926 Mounting The Condensation Hood

fri-jado-20230926-Mounting-The-Condensation-Hood-
product

Product Information

The GO Combi is an oven that requires proper installation and servicing by qualified service technicians. This user manual provides detailed instructions and information for the mounting of the condensation hood.

Product Usage Instructions

Mounting the Condensation Hood
Before mounting the condensation hood, please ensure that you have read and understood the safety information provided in this user manual, as well as in the installation and service manuals.

Mechanical Installation
Ensure that the distance from the condensation hood to the ceiling is a minimum of 300 mm.

Follow the steps below for mechanical installation:

Step 1: Prepare the necessary tools for installation.
Step 2: Identify the appropriate condensation hood for your oven type (standard, PassThrough, Stacking kit, or Stackit PassThrough).
Step 3: Position the condensation hood in the desired location above the oven.
Step 4: Securely mount the condensation hood to the ceiling using appropriate fasteners.
Step 5: Ensure that the condensation hood is properly aligned and leveled.

Electrical Installation
For electrical installation instructions, please refer to the electrical installation section in this user manual.

Testing the Condensation Hood
After mounting the condensation hood, it is important to test its functionality to ensure proper operation. Follow the steps below:

Step 1: Power on the oven.
Step 2: Activate the condensation hood.
Step 3: Observe the condensation hood to ensure that it effectively captures and removes steam and condensation.

For any further assistance or information, please refer to the additional documentation available on our website or contact our customer support.

General information

Target group
This document is aimed at service technicians who have been trained in installing and servicing the oven. The oven must only be installed and serviced by qualified service technicians.
Technical changes
This document is subject to changes without notice.
More documentation
You find more documentation about the oven on our website.
Warranty
You find more information about the warranty on our website.
Permissions
Log in as “Technician” (576021) to have the necessary rights to be able to change the oven setup, use the test functions, update software, etc.

Safety information

Read this document before using, installing, or servicing the product. Installation and operation must comply with local regulations and accepted codes of good practice.
Read the safety instructions in the user manual, installation manual, and service manual before you perform any work on the oven.
All maintenance and repair must be carried out by qualified installation and service technicians only. Installation and/or service by others than qualified service technicians may result in injury to the operator and/or damage to the oven.

Before replacement

Make sure the required tools are available.
Unpack the spare parts and check if all parts are available.
Make sure the working area is tidied up, clean and safe to prevent personal injury and damage to the equipment.

Tools

Drilling machine
Ø5.7 drill
M5 threaded tap

Spare parts

Condensation hood, mounting kit.

Estimated working time
The estimated working time is 1 hour.

Condensation hood overview

$fri-jado-20230926-Mounting-The-Condensation-Hood-fig- $1$$

Mounting the condensation hood

Mechanical installation

IMPORTANT!
The distance from the condensation to the ceiling must be a minimum of 300 mm.

Drill out the center marks in the oven roof in the marked areas using a Ø4.7 drill and an M5 threaded tap. The illustration only shows some of the markings on the right-hand side of the oven. The same must be done on the left-hand side of the oven.
Place the condensation hood on top of the oven.
IMPORTANT!
- Make sure that the pipes in the condensation hood fit on the exhaust pipe and air intake pipe on the oven.
- In the case of a Stacking kit oven, make sure that the pipes in the condensation hood fit on the exhaust pipe and air intake pipe on the upper oven as well as the exhaust pipe for the bottom oven. $fri-jado-20230926-Mounting-The-Condensation-Hood-fig- $4$$
Remove the front.
Remove the six M5x10 screws on the left-hand side.
Remove the side plate on the left-hand side.
Remove the six M5x10 screws on the right-hand side.
Remove the side plate on the right-hand side.
Fasten the condensation hood with four M5x10 screws. $fri-jado-20230926-Mounting-The-Condensation-Hood-fig- $10$$
Remount the side plates and fasten them with six screws.
Remount the front.

Electrical installation

Lead the wire for the IO board through the cable gland.
Lead the wire down the back side of the oven.
Fasten the wire with cable ties.
Remove the side plate.
Lead the wire under the oven and up through the hole for an Ethernet connection.
Lead the wire to the IO board on the front panel. $fri-jado-20230926-Mounting-The-Condensation-Hood-fig- $15$$
Connect the wire to the IO board on J1. $fri-jado-20230926-Mounting-The-Condensation-Hood-fig- $16$$
Put the three-pin plug into the socket.
Switch on power.