CANOPIA BORDEAUX 5×7 Herald Door Awning Kits

Product Information

The product is available in two series:

• Bordeaux Series: White / Mist Glazing
• Herald Series: Grey / Mist Glazing

The product is recyclable and meets the EN 14963:200 standard.
It is also a registered design.

Available Models:

• Bordeaux 5×7 / 1.4×2.2
• Bordeaux 5×15 / 1.4×4.5
• Bordeaux 5×22 / 1.4×6.7
• Bordeaux 5×29 / 1.4×8.9
• Herald 5×7 / 1.4×2.2
• Herald 5×15 / 1.4×4.5
• Herald 5×22 / 1.4×6.7
• Herald 5×29 / 1.4×8.9

Tools & Equipment Required:

• 2 people needed
• Ladder
• Electric Drill with Drill Bit (10mm | 3/8 and 8mm | 5/16)
• Philips head Screwdriver
• Spirit Level
• Work gloves
• Wrench (10mm | 3/8 and 13mm | 1/2)
• Silicone
• Pencil
• Tape measure

If you have any concerns or need assistance, please refer to the How to Assemble video guide by scanning the QR Code provided or visiting canopia.shop /Assemble-Herald. You can also contact our customer support at canopia.shop/support.

Local Customer Care:

• Denmark: 07-575 42 70 | post@nshnordic.com

• Germany: 0599-37-057 | info@ms-viscom.com

• Czech Republic: 0493-523-523 | servis@garland.cz

• Poland: Infolinia: 801-011-929 | 22-349-93-36
  kontakt@ogrodosfera.pl

• Finland: Neuvonta: 09-6866720 Tuki | Varaosat: 050-3715350
  www.horisontenterprises.fi | tuki@horisontenterprises.fi

• Cyprus: 0224-971-13 | alpaco@alpacodomica.com
  www.alpacodomica.com

IMPORTANT!
Please read these instructions carefully before starting assembly.
Keep these instructions in a safe place for future reference.

AVAILABLE MODELS

TOOLS & EQUIPMENT

HAVE A CONCERN?
WE CAN HELP.
Before returning your purchase:

Please take a look at our “How to Assemble” video guide.
Scan the QR Code below or go to canopia.shop/Assemble- Herald

You didn’t find what you were looking for?
We can help at canopia.shop/support

Still can’t find what you are looking for?
Please see next page for local customer care.

WE ARE HERE TO HELP
canopia.com/contact-us

INFORMATION

SAFETY ADVICE

• It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
• We strongly recommend using work gloves during panel sliding.
• Some parts may have sharp edges. Please be careful when handling components.
• Always wear shoes and safety goggles when working with extruded aluminium.
• If using a step ladder or power tools make sure that you follow the manufacturer’s safety advice.
• Keep children away from the assembly area.
• Do not touch overhead power cables with the aluminium profiles.
• Do not attempt to assemble the product in windy or wet conditions.
• Dispose of all plastic bags. Keep them out of reach of small children.
• Do not climb or stand the roof.
• Do not hang or lay the profiles.
• Do not position your product in an area exposed to excessive winds.
• Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
• Make sure there are no hidden pipes or cables in the wall before inserting the pegs.
• This product is designed to be used mainly as a Door Awning.
• Heavy snow load on the roof can make it unsafe to stand below or nearby.
• The wall anchoring kit supplied with this product is suitable for concrete or solidbrick walls. Other wall types need an accordant wall fixation kit.

BEFORE ASSEMBLY

Selecting a site:

• Choose your site carefully before beginning assembly.
• Consider the door’s opening – inside or outside.
• The product must be positioned and fixed on a flat level surface.
• This is a multi-part assembly best achieved by two people. Allow at least half a day for the assembly process.
• Take all components & parts out of the packages. Sort the parts and check against the content parts list.
• Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.
• Please note multi-sided profiles are used in this Door Awning. As a result some holes in the profiles are not used during assembly.
• Please review entire instructions before starting. Carry out the assembly steps in exact order.
• Please consult your local authorities if any permits are required prior to constructing the product.

IMPORTANT!

• During assembly use a soft surface below the parts to avoid scratches and damages .

• You are solely responsible for determining whether the handling, storage, assembly, installation or use of this product is safe and appropriate in any location
  or for any given application

• The manufacturer is not responsible for any damages or injury to you, any other person or any property resulting from the improper handling, storage, installation, assembly or use of this product, or the failure to follow the manufacturer’s written instructions regarding the handling, storage, installation, assembly and use of this product

• This product is intended for normal residential use only Do not use this product for any application that is not recommended in these instructions or building codes in effect in location where this product will be used. Always take care and use appropriate safety equipment (including eye protection) when assembling or installing this product

• We recommend checking for restrictions or covenants for building this product in your area.
  In addition we advise to check if you need to submit any forms or if any permit is required prior to building the product

DURING ASSEMBLY

During assembly, you will encounter different icons for different products. Please see below for more information:

You may use silicone lubricant spray on the frame in order to help you slide the panels into the profiles Do not spray the panels

Use a rubber mallet if necessary

Make sure you remove covering plastic film from both sides of the panel

All panels with the stamped words “THIS SIDE OUT’ must be facing out to create full UV protection. Remove plastic sticker as panels are locked in place

Steps marked with dashed outlines refer to Extensions only
Some of the steps are irrelevant for an assembly of a single product
When assembling a single or an extended product,some parts may be surplus

These 2 icons below indicate if screw’s tightening is required or not
Temporary tightening of a few screws may be needed to prevent a profile from sliding out
Tighten all screws once assembly is completed

CARE & MAINTENANCE

• When your product needs to be cleaned, use a soft cloth and rinse with cold clean water .
• DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels
• Clean the product once assembly is complete

IMPORTANT ASSEMBLY STEPS

When encountering this information icon during assembly, please refer the relevant assembly step for important additional comments.

Step 1:

Important!

Please make sure the frame is perfectly centered before fixing.
The minimum installation height, above the door frame, is 45 cm.

Step 4:
Please apply silicone sealants above beam #9592, in order to prevent water from seeping in.

Step 11:
When extending the product, please apply silicone sealants between profiles

9745, in order to prevent water from seeping in.

Step 17:
Please make sure you install the panels with the UV protected side out (marked with “THIS SIDE OUT”) and remove the sticker as panels are in place.

Step 20:
Please apply silicone sealant on the inner part of #8167 and connect to the profile.

Step 21:
Note: when assembling an extension, some parts and screws will be surplus.

 3 YEAR LIMITED WARRANTY

Palram Canopia Ltd. (Company number: 512106824) whose registered office is at Teradion Industrial Park, M.P Misgav 2017400, Israel (“Canopia”) warrants that the product will be free from defects in material or workmanship for a period of 3 years from the original date of purchase.

• This warranty is valid only if the product is installed, handled, cleaned, and maintained in accordance with Canopia’s written specifications.
• This warranty does not cover defects resulting from normal wear and tear including, but not limited to: damage caused by use of force, incorrect handling, inappropriate use, negligence, accidents, impact from foreign objects, vandalism, pollutants, alteration, painting, damage resulting from cleaning with incompatible detergents or minor deviations of the product.
• This warranty does not apply to damage resulting from “acts of Nature”, which includes but is not limited to hail, storm, tornado, hurricane, blizzard, flood, or fire.
• Upon submitting proof of purchase and evidence of the claimed product failure, and subject to reporting the failure in writing within 30 days after discovery of the defect, Canopia, at its sole discretion, will replace defective parts of the Product, or refund you a prorated portion of the purchase price on a straight-line depreciated basis for the length of the warranty.

Declaration of Performance
According to Construction Products Council Directive UE N°305/2011 and EN 14963:2006

Issue Date 01/01/2022

1. Identification code: Bourdeaux™, refer to CE label no 013

2. Type: Alight transmitting wall-supported 3 mm thickness solid PMMA extruded sheets structure made of aluminum and galvanized steel elements

3. Intended use: open multi-purpose covering

4. Manufacturer: Palram Canopia Ltd. Teradion Industrial Park, M.P Misgav 2017400, P.O.B. 53, Israel

5. Importer and EU representative: PALRAM Applications UK, Unit 40|3 Industrial Estate Carr Hill,Doncaster DN4 8DE

6. Assessment and verification of constancy of performance: System 3

7. Declared performance:

   • Resistance to upward load: UL 700
   • Resistance to downward loads: DL 1200
   • Reaction to fire: B, 51, do
   • For mounting and fixing provisions see EN 16153:2013
   • Resistance to fire: NPD
   • External fire performance: FRooF
   • Water tightness:
   • For the rooflight with upstand: Pass
   • For the sheet material: Pass
   • Impact resistance:
   • For the small hard body: Pass
   • For the large soft body: Pass
   • Thermal transmittance:
   • For the rooflight: NPD (not relevant to an open multi purpose cover)
   • For the sheet material: 5.9 W/(m2•K)
   • Direct airborne sound insulation: NPD (not relevant to an open multi purpose cover)
   • Radiation transmittance:
   • Light transmittance: Tv – 92.4 %
   • Solar direct transmittance: Te – 82.14 %
   • Solar factor: g value – 0.85
     Air permeability:
     For the rooflight: NPD (not relevant to an open multi purpose cover)
     For the sheet material: Pass
     Durability (of the sheet material): ДА, Cu 1, Ku O

8. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 7.
   This declaration of performance is issued, in accordance with Annex ZA.2.2 – EN 14963:2006,under the sole responsibility of Palram Canopia Ltd.
   ITT reports and Factory Production Control records are available upon request at www.canopia.com

Palram Canopia Ltd.
Teradion Industrial Park, M.P Misgav 2017400, P.O.B 53, Israel
Tel +972.4.848.6900 | Fax +972.4.848.6901
canopia@palram.com | www.canopia.com

References

• Contact Us Archive - Canopia
• YouTube
• Support Archive - Canopia
• Inspection Systems for the Electronics Industry – Viscom – Viscom
• Αρχική Σελίδα - Alpaco Domica
• Canopia United Kingdom - Celebrate Outdoor Living
• Contact Us Archive - Canopia UK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>