STEEL MATE SPT100 Steelmate Automotive Diagnostic Tool User Manual
- June 4, 2024
- STEEL MATE
Table of Contents
SPT100
TPMS Diagnostic Tool
User Manual
Specifications
TPMS Diagnostic Tool
Operating frequency: 125KHz, 433/434MHz, 315MHz
Operating voltage: 3.7V
Operating temperature: -10°C~ 60°C
Storage temperature: -20°C~ 70°C
Sensor
Operating frequency: 125KHz, 433/434MHz, 31 5MHz
Operating voltage: 2.1~3.3V
Operating temperature: -40°C~ 105°C
Storage temperature: -40°C~ 125°C
Static current: <1.0 uA
Pressure range: O~7 Bar
Brief look
Includes
TPMS Diagnostic Tool, OBDII CABLE, USB CABLE, Manual
Power ON/OFF
Power ON: Press the power button to turn on the device.
Power OFF: Press the power button to turn off the device. Or the device
will turn off automatically without any operation in 3 minutes.
Note: The time of auto power can be set in [System Setting].
How to operate
From the main menu, press the Direction button to select the [TPMS diagnosis]
function, and enter the test vehicle information selection page.
Note: All function screens shown in this manual are for reference only, actual
screens may vary for each vehicle being tested. Please follow [Function 5 Tire
pressure relearning method] to check the related relearning methods.
1. Tire pressure service interface
For direct TPMS in vehicles
|
For indirect TPMS in vehicles
---|---
Mainly include: Trigger and check the tire pressure sensor, tire pressure
system diagnosis, program the tire pressure sensor, view relearning step,view
the original tire pressure sensor information| Only include: view relearning
step
2. Trigger and check the tire pressure sensor
Note: If part of the sensors does not acquire the data, please back to
the Tire pressure service interface, then select [Diagnostics] to acquire the
sensor ID or more information.
| 
| 
---|---|---
Press the direction button to select the desired position, and take the device
close to the sensor.| Press the buttons to trigger the sensor.| After the
trigger succeeds, the sensor data will be displayed on the screen.
3. Tire pressure system diagnosis
| Use OBD cable to connect
with device and vehicle OBDII interface, and turn the ignition ON
---|---
| The device will
automatically read the original sensor ID and related fault code of the
vehicle tire pressure system.
| Press the button to select
[OBD relearn], and press the OK button can directly enter the OBD relearn
function.
| Press the button to select
[View fault code], and press the OK button can view the fault codes and their
meaning.
| Press the button to select
[Clear fault code], and press the OK button can clear the fault code.
4. Program the tire pressure sensor
This function is to recover a sensor ID in order to enter it into the spare
blank sensor. If the original sensor can be read, use the Copy functions to
recover the ID. If it cannot be read, use the Auto Create function to create a
randomized ID.
a. Auto-create sensors
This function is to create a sole senor ID of new sensors, these ID are random
generation. The newly generate sensor ID is usually different from the sensor
ID which is stored by the original tire pressure system. so need learn the
newly generate sensor ID into the original tire pressure system.
| 
---|---
Take the waited programming sensor close to the sensor placement position of
the device.| If 1-8 sensors are scanned at the same time, press the direction
button to select the waited programming sensor, and press the OK button to
confirm.
|
Press the button to start the program.| After being programmed, the sensor SN
and inputted ID will be displayed on the screen.
| 
If some sensor programming failed| The failed information will be displayed on
the screen.
b. Copy by input
| 
---|---
Press the OK button to enter the next step.| Press the direction button to
enter the ID as same as the original tire pressure to be re-programmed.
|
Take the waited programming sensor close to the sensor placement position of
the device.| If 1-8 sensors are scanned at the same time, press the direction
button to select the wafted programming sensor, and press the OK button to
confirm.
| 
Press the button to start the program.| After being programmed, the sensor SN
and inputted ID will be displayed on the screen.
c.Copy by activation
| 
---|---
The triggered sensors information in step 1 will be displayed on the screen,
press the direction button to select the sensor to be programmed, and then
press the OK button to enter the next step.| Take the waited programming
sensor close to the sensor placement position of the device.
| 
If 1-6 sensors are scanned at the same time, press the direction button to
select the waited programming sensor, and press the OK button to confirm.|
Press the button to start the program.
After being programmed, the sensor SN and inputted ID will be displayed on the
screen.
d.Copy by OBD
| | 
---|---|---
Use the OBD cable to connect with the device and vehicle OBDII interface and
turn the ignition ON| The original sensors’ information will be displayed on
the screen, press the direction button to select the sensor to be programmed,
and then press the OK button to enter the next step.| Take the waited
programming sensor close to the sensor placement position of the device.
| 
| 
---|---|---
If 1-6 sensors are scanned at the same time, press the direction button to
select the waited programming sensor, and press the OK button to confirm.|
Press the buttons to start the program.| After being programmed, the sensor SN
and inputted ID will be displayed on the screen.
5. Tire pressure relearning method
Please read relearning steps to operate.
6. Original sensor information
| 
| 
---|---|---
Press the direction button to select the original sensor information or
Steelmate sensor information, and then press the OK button to enter the next
step.| The original sensor information will be displayed on the screen.| Take
the device close to the sensor, then Steelmate sensor information will be
displayed on the screen.
Battery charging
This device is equipped 3000mN3.7V interior lithium polymer chargeable
battery.
In order to get the device working at its best, please full charge the
battery. Suggest at least 2 hours to charge before at the first time to use.
System settings
From the main menu, press the Direction button to select [Setting], and press the OK button to enter the setting page.
Recent test
From the main menu, press the Direction button to select [Recent test], then review the last tested vehicle information and sensor trigger data, and press the OK button can continue the last unfinished operation.
Upgrade
From the main menu, press the Direction button to select [Upgrade], then follow the steps shown on the left to upgrade the device software.
About
From the main menu, press the Direction button to select [About], then view the product information such as software, hardware version, serial number, and upgrade password.
T hink safety think Steelmate
STEELMATE CO., LTD.
StecImam Industrial Park. Hoping Street. Donate Road, Dongfeng
Town, Zhongshan City, Guangdong, P.R. aline 528425 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>