SVL SRSB2819SRGB RF Bluetooth RGB CCT Remote Controller Instruction Manual

SVL SRSB2819SRGB RF Bluetooth RGB CCT Remote Controller

Product Information:

• Product Name: RF+Bluetooth RGB+CCT Remote Controller
• Model Number: 70010127

Function Introduction:

• W button: Controls color temperature; click to cycle through 100%CW, 50%CW+50%WW, 100%WW, and OFF; press and hold to decrease CW and increase WW; release and hold again to increase CW and decrease WW; press and hold down to decrease light intensity
• Click: Turns ON/OFF all zones
• 20 RGB color changing modes: Click to play a mode, click again to pause current mode, click again to play next mode; press and hold down to speed up/down the modes
• W+: Click to choose the zone/zones; press and hold down to turn on/off corresponding zone; press and hold down to increase light intensity
• S1, S2, S3: Scene buttons to save and recall colors/scenes/modes

Indicator: Indicates the state of the remote control

Color Wheel: Touch to select RGB color

Zone Numbers: Click to choose the zone/zones; press and hold down to turn on/off corresponding zone

Product Data:

• Output: RF+Bluetooth signal
• Operation Frequency: 2.4GHz
• Power Supply: 4.5V (3xAAA battery)
• Operating Temperature: 8% to 80%
• Dimensions: 120x55x17mm

Product Usage Instructions

Pair with RF+Bluetooth Receiver:

1. Do wiring the receiver according to the wiring diagram of the RF+Bluetooth receiver you want to pair with.
2. Click to activate the remote.
3. Click the Prog button or Reset button on the receiver or re-power on the receiver three times continuously to set it into pairing status.
4. Click a zone button to select a zone (e.g., zone 4).
5. Immediately touch the color wheel; LED lights connected with the receiver flicker once, indicating successful pairing with zone 4.

If using multiple receivers:

• Option 1: Have all the receivers in the same zone, like zone 1.
• Option 2: Have each receiver in a different zone, like zone 1, 2, 3, or 4.

Save Color/Scene/Mode:

1. Click ON/OFF button to activate the remote.
2. Choose and click one or multiple paired zone numbers (e.g., zone 4).
3. Touch the color wheel or click the other buttons to select the scene you like.
4. Press and hold any scene buttons of S1-S3 (e.g., S3); LED lights connected with the RF receiver flicker once, indicating successful saving of the color/scene.

Recall the Saved Colors/Scenes:

1. Click ON/OFF button to activate the remote.
2. Choose and click one or multiple paired zone numbers (e.g., zone 4).
3. Click any scene buttons of S1-S3 (e.g., S3) to recall the saved scene.

Set Sync for Multiple Receivers:

1. Do wiring the receivers according to the wiring diagram of the receiver you want to pair with.
2. Click ON/OFF button to activate the remote.

Important: Read All Instructions Prior to Installation

Function introduction

Product Data

• Control 4 zones of RF+Bluetooth receivers separately.
• RGB+CCT color controller
• High sensitive & high stable, fast & precise color control.
• Compatible with all universal series RF+Bluetooth receivers
• 1 receiver can be paired by max 8 different remote controls.
• Waterproof grade: IP20

Safety & Warnings

• This device contains AAA batteries that shall be stored and disposed properly.
• DO NOT expose the device to moisture.

Pair with RF+Bluetooth Receiver

Step 1: Do wiring the receiver according to wiring diagram(please refer to the instruction of RF+Bluetooth receiver that you would like to pair with.

Step 2: Click to activate the remote.

Step 3: Click the “Prog” button or “Reset” button on the receiver or re- power on the receiver three times continuously to set it into pairing status

Step 4: Click a zone button to select a zone (e.g. zone 4).

Step 5: Then immediately touch the color wheel, LED lights connected with the receiver flicker once means the receiver is paired with zone 4 successfully.

If you use multiple receivers, you have two choices:

Option

1. have all the receivers in the same zone, like zone 1
2. have each receiver in a different zone, like zone 1, 2, 3 or 4

Save color/scene/mode

Recall the saved colors/scenes

20 Color Changing Modes

• Colorful Mixed
• Red Shade
• Green Shade
• Blue Shade
• Yellow Shade
• Cyan Shade
• Purple Shade
• White Shade
• Red Green Shade
• Red Blue Shade
• Green Blue Shade
• Colorful Strobe
• Red Strobe
• Green Strobe
• Blue Strobe
• Yellow Strobe
• Cyan Strobe
• Purple Strobe
• White Strobe
• Colorful Jump

Set Sync for Multiple Receivers

Step 1: Do wiring the receivers according to wiring diagram(please refer to the instruction of the receiver that you would like to pair with.)

Step 2: Click ON/OFF button to activate the remote

Step 3: Click the “Prog. Key” button on 1st RF+Bluetooth receiver 3 times to set it as master receiver and enter pairing to RF remote status.

Step 4: Click a zone button to select a zone 1/2/3/4 (e.g. zone 4).

Step 5: Then immediately touch the RGB color wheel, LED lights connected with the 1st receiver flicker once means the receiver is paired with zone 4 as the master receiver successfully.

Step 6: Click the “Prog. Key” button on 2nd RF+Bluetooth receiver 2 times to set it as a slave receiver and enter pairing to RF remote status.

Step 7: Click the same zone button which the master receiver has paired to, here it’s zone 4.

Step 8: Then immediately touch the RGB color wheel, LED lights connected with the 2nd receiver flicker once means the receiver is paired with zone 4 as a slave receiver successfully.

Step 9: Pair more slave receivers by following above Step 6, Step 7 and Step 8.

Step 10: Click the zone button that the master receiver and slave receivers have paired to, here it’s zone 4.

Step 11: Click play button “ ” to play the color running modes, the master receiver will send sync signal to all slave receivers, after a short while, all receivers will be in sync mode.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>