SVL V2-L RF CCT Dual Color LED Controller User Guide
- May 15, 2024
- SVL
Table of Contents
SVL V2-L RF CCT Dual Color LED Controller User Guide
Features
- 4096 levels 0-100% dimming smoothly without any flash.
- Match with all RF 2.4G single zone or multiple zone dual color or remote control.
- One RF controller accept up to 10 remote control.
- Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance.
- Synchronize on multiple number of controllers.
- Fade in and out effect selectable.
- 3 levels color temperature (WW, NW and CW) selectable by continuous power off and on operation.
- Connect with external push switch to achieve on/off and 0-100% dimming function.
- Over-load / Short circuit protection, recover automatically
Technical Parameters
Input and Output
| Input voltage | 12-48VDC |
|---|---|
| Input current | 16.5A |
| Output voltage | 2x(12-48)VDC |
| Output current | 2CH,8A/CH |
| Output power | 2496-384)W |
| Output type | Constant voltage |
| Warranty | |
| Warranty | 5 years |
Dimming data
| Input signal | RF 2.4GHz + Push Dim |
|---|---|
| Control distance | 30m(Barrier-free space) |
| Dimming gray scale | 4096 (2^12) levels |
| Dimming range | 0 -100% |
| Dimming curve | Linear |
| PWM frequency | 2KHz (default) |
| Package | |
| Size | [178 x W50 x H38mm |
| Gross weight | 0.126kg |
Safety and EMC
| EMC standard (EMC) | ETSI EN 301 489-1 V2.2.3ETSI EN 301 489-17 V3.2.4 |
|---|---|
| Safety standard(LVD) | EN 62368-1:2020+Al 1:202C |
| Radio Equipment(RED) | ETSI EN 300 328 V2.2.2 |
| Certification | CE,EMC,LVD,RED |
| Environment | |
| Operation temperature | Ta: – 30 ° C – +55°C |
| Case temperature (Max.) | Tc: +85°C |
| IP rating | IP20 |
Mechanical Structures and Installations
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key (single zone remote) or
zone key (multiple zone remote) of the remote.
The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast
flash a few times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Wiring Diagram
Wire Preparation:
-
The wiring can be solid or stranded with a cross-sectional area of 0.5 to 2 mm².
Conventional 1mm² can withstand 10A output current. -
When wiring is installed, the terminals must be tightened.
If they are not tightened, the contact point resistance will be too high and the terminals will easily burn due to heat when used at full load for a long time.
Note:
-
Continuously switch off and on the power supply two times rapidly, it will change WW, NW and CW 3 levels color temperature in sequence (factory setting).
-
Long press the match key for 15s to cancel the continuous switch off-on to switch 3 levels color temperature function.
Long press the match key for 10s to restore the factory setting. -
The output power of a constant voltage power supply should be at least 1.2 times that of the output load (light strip), otherwise the full power output of the load can easily cause automatic flickering or shaking of the light.
Light on/off fade time
Long press match key 5s, then short press match key 3 times, the lighting effect will be set to the fade in and fade out in 3s, the indicator light of LED controller blinks 3 times.
Long press match key 10s, restore factory default parameter, the light on/off time restores to 0.5s.
Push Dim
The provided Push-Dim interface allows for a simple dimming method using
commercially available non-latching(momentary) wall switchs.
If more than one controller are connected to the same push switch, do a long
press for more than 10s, then the system is synchronized and all lights in the
group dim up to 100%.
This means there is no need for any additional synchrony wire in larger
installations. We recommend the number of controllers connected to a push
switch does not exceed 25 pieces, The maximum length of the wires from push to
controller should be no more than 20 meters.
Dual color control
WW=Warm white LED CW=Cool white LED Each channel can supply up to 192W(@24V) and white balance can be controlled as such:
Linear dual color tuning
Dimming curve
Installation Precautions
- The products shall not be stacked, the distance should be ≥ 20cm, so as not to affect lifespan of the products due to poor heat dissipation.
- The product shall not be installed close to the switching power supply with an interval of ≥ 20cm to avoid radiation interference of the switching power supply.
- The installation height shall be ≥ 1m from the oor to avoid shortening the remote control distance due to too weak reception signal.
- The products are not allowed to be close to or covered by metal objects, with an interval of ≥ 20cm to avoid signal attenuation and shorten the remote distance.
- Avoid installation at the corner of the wall or the corner of the beam, with an interval of ≥ 20cm to avoid signal interference.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>