Moes WS-SR-US-T Star Ring Smart Wi-Fi 3 Way Single Pole Push Button Light Switch Instruction Manual

Moes WS-SR-US-T Star Ring Smart Wi-Fi 3 Way Single Pole Push Button Light

Switch

Product Information

• Model: WS-SR-US-T
• Input Power : 100~245V AC 50/60Hz
• Control Principle : Relay
• Wireless Protocol : WiFi 802.11 b/g/n 2.4GHz
• Max Current : 10A
• Standby Power : 0.5W
• Button Life : 500K times
• Dimension : 1064535 mm

Product Usage Instructions

1. Turn off the power to each switch you are replacing by locating your circuit breaker panel.
2. Remove the old switch and pull it away from the wall.
3. Verify that the power is off by using an electrical tester to test all wires connected to the switch.
4. If necessary, turn off additional circuits until no voltage is found on the neutral wires from neighboring circuits.
5. Identify the old switch type
   • A Single Pole Switch : Only one switch controls one light or a bundle of lights.
   • A 3-Way Switch : Two switches control the same light or the same bundle of lights.
6. Pull out the old switch and identify the line/load wire (usually black, attached with a black screw, and may be remarked common) for both single pole and 3-way switches.
7. Find the neutral wires in the wall (usually a bundle of one or more white wires) and make sure they are available for installation. If there is no neutral, try another location or call an electrician for help.
8. Test the neutral and ground wires to ensure there is no power on the neutral wires from neighboring circuits. The ground wires  are usually bare copper or green.
9. Take pictures of the wiring for reference.
10. Install the smart switch according to the provided 3-way wiring diagram, replacing one of your regular 3-way switches with the smart switch.
11. Tighten the screw terminals and secure the new switch in place.

Product Outline

Indicator Light Status03 Specification

Specification

Contents Supplied

Safety Information

WARNING: RISK OF ELECTRIC SHOCK
Electricity can cause personal injury and property damage if handled improperly. If you are not sure about any part of these instructions, please seek professional assistance from a qualified electrician.
Ensure all wark meets applicable local and national codes.

Tools you’ll need

Installation

STEP 1

Turn Off Power
Locate your circuit breaker panel and turn off the power to each switch you are replacing.

Circuit breaker panel

Attention
Please disconnect the power supply before installing or removing the device for avoiding irreversible damage on the device from the electric current or some unpredictable problems such as lamp flashing.

• STEP 2
  Remove the switch and pull it away from the wall.

• STEP 3

  • Verify Power is Off
  • We recommend you to remove the faceplate from the old switch and use an electrical tester to test all wires connected to the switch to ensure there is no voltage in the circuit.
  • You may need to turn off more than one circuit breaker.

• STEP 4

  • Pull Out Old Switch

• STEP 5

  • Identify The Old Switch

Single Pole Switch
Only one switch control one light or a bundle of lights.

3-Way Switch
Two switches control the same light or the same bundle of lights.

• STEP 6
  • identify Line/Load Wire

Note: The color of your wire may be different from the color shown on the manual.
LINE/LOAD wire (usually BLACK, attached with a black screw, and may be Remarked “common”.)

Single Pole Switch

3-Way Switch

• STEP 7
  • Find the NEUTRAL Wires
  • Neutral wire is required to install the smart light switch. Most likely a bundle of one or more white wires in the wall.
  • Note : If there is no neutral, please try another location or call an electrician for help.
• STEP 8
  • Test NEUTRAL and GROUND Wires
  • Make sure there is no power on the neutral wires from neighbor in circuit. lf necessary, shut off additional circuits until no voltage is found.
  • GROUND wires are usually BARE COPPER or GREEN.
• STEP 9
  • Take Pictures of the Wiring
  • Loosen the screw terminals and remove the old switch.
• STEP 10
  • Wire the Smart Switch Single Pole Wiring Diagram ( 3-Way Model）
  • Cap off the remaining L2 wire (RED) from the Switch with a wire nut.

Way Wiring Diagram

Replace ONE of your REGULAR 3-WAY SWITCHES with SMART SWITCH

Way Wiring Diagram
Replace BOTH of your REGULAR 3-WAY SWITCHES with SMART SWITCHES

Not Working Situation

• STEP 11
  • Mount the switch
• STEP 12
  • Turn on the power

Add Devices

1. Download MOES App on App store or scan the QR code
   • MOES App is upgraded as much more compatibility than Tuya Smart/Smart Life App, functional well for scene controlled by Siri, widget and scene recommendations as the fully new customized service.
   • (Note : Tuya Smart/Smart Life App still works, but MOES App is highly recommended)
2. Registration or Log in.
   • Download “MOES” Application.
   • Enter the Register/Login interface; tap “Register” to create an account by entering your phone number to get verification code and “Set password”. Choose “Log in” if you already have a MOES account.
3. Configure the APP to the switch.
   • Preparation : Ensure the switch has been connected with electricity; ensure your phone has been connected to Wi-Fi and is able to connect to the Internet.

Wi-Fi link method:(two pairing methods)

Complete the wiring of the switch module before pairing

Note
The switch only supports 2.4G network. If you have connected 5G network, please disconnect 5G network firstly and connect 2.4G network.

1. Method one
   Scan the QR code to configure the network guide.

Method two
Pair and clear up the WiFi code with Bluetooth and WiFi connected meantime.(New Updated)

1. Press and hold switch button for 6s until the white indicator flashes to reset the switch and get into quick configure mode.
2. Make sure your phone is connected to Wi-Fi and Bluetooth.
3. Open Smart Life/Tuya App and Click“+”,then the prompt page will automatically show on the screen.Click “Go to add”.
4. Select the device you want to add and click “+”
5. Enter Wi-Fi Password and click “Next”,waiting for completing the connection.
6. Add the device successfully, you can edit the name of the device to enter the device page by click “Done”

Smart Life Skills (Alexa)

• STEP 1
  • Complete the device’s networking configuration according to the prompts in the App.
• STEP 2
  • If you have already configured Amazon Echo, you can skip this step. The following instructions are based on the iOS client.
  • Make sure you Amazon Echo device is powered on and connected to a Wi-Fi network.
  • Open the Alexa App on your phone. After successful login, tap on the menu in the upper left corner of the Home page, select “Settings” and tap “Set Up A New Device” to set up the Amazon Echo.
  • Choose your Amazon Echo device type and language for connecting. Press and hold the small dot on the d evice until the light turns yellow. Then tap “Continue” to connect to the hotspot.
  • After connecting to the Amazon Echo hotspot, return to the page. At this point, the connection is successful. Tap “Continue” to proceed to the next step. Choose a Wi-Fi network to connect to. Amazon
  • Echo will take a few minutes to try to connect to the network.
  • After the network connection is successful, tap “Continue”. An introduction video will appear. After the video ends, tap “Continue” to jump to the Alexa Home page. You have now completed the
  • Amazon Echo’s configuration process.
  • Then search for “App Name”. Tap “Enable” to enable the Skill.
• STEP 3
  • Key step —— Link Skill
  • Tap on “Skills” in the Alexa App menu.
  • Enter the App account and password, then tap “Link Now” to link your App account to enable the Skill. Now you can start your smart home journey.
• STEP 4
  • Control the device via voice commands, now you can control your smart device with Echo. You can control your device (such as your bedroom light) with the following commands
  • Alexa, turn on/off bedroom light.
  • Alexa, set bedroom light to 50 percent.
  • Alexa, brighten/dim bedroom light.
  • Alexa, set bedroom light to green.

Smart Life Skills (Google)

• STEP 1

  • Complete the device’s networking configuration according to the prompts in the App.

• STEP 2

  • If you have already configured Google Home, you can skip this step. The following instructions are based on the iOS client.
  • Make sure you Google Home device is powered on and connected to a Wi-Fi network.
  • Open the Google Home App on your phone. After successful login, tap on the menu in the upper left corner and select “SET UP” to set up Google Home.
  • It will notify you with a sound to ensure that you are connected to the correct device. After you hear the sound, tap “YES” to proceed to the next step.
  • You can choose to differentiate the room where Google Home is located from other Google devices. Then, select the Wi-Fi network and language, wait for the system to complete the configuration, and tap “next”. According to the page prompts, choose whether to agree to the corresponding operation. When the page displays “Google Home is ready,” select “continue” to the next step.
  • Next is the voice control guide tutorial. Once you are done listening, tap “FINISH SET UP”. At this point, Google Home setup is complete.

• STEP 3

  • Key step —— Link Skill
  • On the main page of the Google Home App, tap the sidebar menu in the top left corner and select “Home Control”. Then tap the plus sign in the lower right corner and search for “App Name”.
  • Find App Name on the list and open it, select the country where your App account is located, enter your App account and a password, and tap “Link Now”.
  • Enter the App account and password, then tap “Link Now” to link your App account. Choose the room where your device is located, and then the skill will appear on the Home Control Devices list.
  • Now you can begin your smart home journey.

• STEP 4

  • Control the device via voice commands, now you can control your smart device with Google Home. You can control your device (such as your bedroom light) with the following commands
  • Ok Google, turn on/off bedroom light.
  • Ok Google, set bedroom light to 50 percent.
  • Ok Google, brighten bedroom light.
  • Ok Google, set bedroom light to red.

FAQ

If you cannot add your Smart Device , please check

1. Whether the Smart Device is powered on.
2. Whether the phone is connected with 2.4GHz Wi-Fi network.
3. Please check routers or related: if your router is dual-band, please select 2.4GHz Wi-Fi network to connect your phone and Smart Plug.
4. Setting up Wi-Fi router: setting encryption method as WPA2-PSK and authorization type as AES, or set both as auto. Wireless mode cannot be 11n only.
5. Please use English and numbers to name your Wi-Fi router. Otherwise our Smart Plug may not recognize it when you try to add it into Smart Life.
6. To stay strong Wi-Fi connection, please keep smart device close to router.
7. Whether connected devices have reached the maximum number of router’s connections. If so, please turn off some devices connected to the router and try again.

SERVICE

1. During the free warranty period, if the product breaks down during normal use, we will offer free maintenance for the product.
2. Natural disasters/man-made equipment failures, disassembly and repair without the permission of our company, no warranty card, products beyond the free warranty period, etc., are not within the scope of free warranty
3. Any commitment (oral or written) made by the third party (including the dealer/service provider) to the user beyond the warranty scope shall be executed by the third party
4. Please keep this warranty card to ensure your rights
5. Our company may update or change the products without notice. Please refer to the official website for the updates

RECYCLING INFORMATION
All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19 / EU) must be disposed of separately from unsorted municipal waste.
To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

WARRANTY CARD

Product Information Product Name Product Type Purchase date Warranty Period Dealer Information Customer’s Name Customer Phone Customer Address

Maintenance Records

Thank you for your support and purchase at we Moes, we are always here for your complete satisfaction, just feel free to share your great shopping experience with us.

If you have any other need, please do not hesitate to contact us first, we will try to meet your demand.

• @moessmart
• @moes_smart
• @moes_smart
• MOES.Official
• @moes_smart
• www.moes.net

AMZLAB GmbH
Laubenhof 23, 45326 Essen
EVATOST CONSULTING LTD

• Address : Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR
• Tel :+442921680945
• Email :contact@evatmaster.com

WENZHOU NOVA NEW ENERGY CO.,LTD

Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China
Tel:+86-577-57186815
Email: service@moeshouse.com
Made In China

References

• MOES Smart: Create Your Smart Life With Smart Home Devices

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>