at t H50 Bluetooth Wired Headphones User Manual
- June 13, 2024
- AT&T
Table of Contents
at t H50 Bluetooth Wired Headphones
Product Information
- Product Name: AT&T H50
- Features:
- Bluetooth 5.0 technology with amazing sound
- Built-in microphone with echo cancellation
- Full controls for playback and calls
- 3.5 mm auxiliary input jack
- Included Items:
- Micro USB Cable
- Audio Cord
- Bluetooth Headphones
Product Usage Instructions
Charging
- Connect the H50 to any USB jack or wall charger using the provided Micro USB Cable.
- The LED indicator will glow red, indicating that the headphones are charging.
- Before using for the first time, charge the headphones for at least 4 hours.
- After the initial charge, subsequent charges will take approximately 2 to 3 hours.
- The LED indicator will turn off when the charging is complete.
Note: When the battery is fully charged, the LED indicator will change to blue.
Power ON/OFF
To power on the headphones:
- Press and hold the ON/OFF button for 2-3 seconds.
- The LED will flash blue, indicating that the headphones are powered on.
To power off the headphones:
- Press and hold the ON/OFF button for 3 seconds.
- The LED will flash blue and then turn off, indicating that the headphones are powered off.
Pairing
- Ensure that the headphones are powered off.
- Follow the Bluetooth pairing instructions provided by your device (e.g., smartphone, tablet, etc.) to search for and connect to the AT&T H50.
Making Phone Calls
- Ensure that the headphones are paired with your device.
- Use the controls on the headphones to answer or reject calls.
Listening to Music
- Ensure that the headphones are paired with your device.
- Use the controls on the headphones to play, pause, skip songs, adjust volume, etc.
LED Indicator Chart
The LED indicator on the headphones provides various indications. Please
refer to the user manual for details on interpreting the LED indicator chart.
| Status | Indicator |
|---|---|
| Powering ON | Blue and red lights flashing rapidly |
| Powering OFF | LED turns off |
| Low battery | Blinking red & headset emits a beep |
| Charging | Solid red light |
| Pairing mode | Blue and red lights flashing rapidly |
| Connection complete | Blue light blinks every 3 seconds |
| Playing music | Blinking blue light |
Troubleshooting
If you encounter any issues with the AT&T H50 headphones, please refer to
the troubleshooting section in the user manual for assistance.
| Symptom | Solution |
|---|---|
| Music is not streaming over Bluetooth | Check to make sure both devices are |
paired and connected over Bluetooth. Restart the H50 to auto- connect with
your Bluetooth device.
No power| Make sure the H50 is fully charged.
H50 does not answer phone calls| Check to make sure both devices are paired
and connected over Bluetooth. Restart the H50 to auto- connect with your
Bluetooth device.
Music does not resume after ending a call| Press play to resume music.
Safety Information
Please read all safety and operating instructions carefully before installation and use. Keep these instructions handy for future reference. Take special note of all warnings listed in the user manual and on the H50 headphones.
Important Safety Instructions
Please read all safety and operating instructions carefully before
installation and use, and keep these instructions handy for future reference.
Take special note of all warnings listed in this user’s manual and on the H50.
-
Attachments: Do not use attachments not recommended by the manufacturer.
-
Water and Moisture: The headphones should not be used near water. The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.
-
Objects and Liquid Entry: Take care to prevent external objects from falling into the headphones and avoid spilling liquids on them. Care should be taken so that external objects do not fall into and liquids are not spilled onto any openings or vents located on the product.
-
Power Source: Connect the headphones only to a compatible power supply as described in the operating instructions or marked on the unit. The unit should be connected only to
a power supply of the type described in the operating instructions or as marked on the unit. If you are not sure, please consult the dealer or local power company. -
Heat: Keep the headphones away from heat sources. The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat.
-
Servicing: Do not attempt to service the headphones yourself. Refer to qualified service personnel for any servicing needs. The user should not attempt to service the unit beyond those methods described in the user’s manual. Opening or removing covers will expose you to dangerous voltage and other hazards. Service methods not covered in the user’s manual should be referred to qualified service personnel.
Features
- Bluetooth 5.0 technology with amazing sound
- Built-in microphone with echo cancellation
- Full controls for playback and calls
- 3.5 mm auxiliary input jack
What’s Included
Unpack the Bluetooth® headphones and make sure all accessories are put aside so they will not be lost.
Getting Started
Location of Main Unit Controls
Operational Instructions
Charging
Charge your H50 through any USB jack or wall charger. The LED indicator will
glow red when charging. Before using for the first time, charge at least 4
hours. After the first charge, the headset will charge in 2 to 3 hours and the
LED indicator will turn off when the charge is complete.
Note: When the battery is fully charged, the LED indicator will change to
blue.
Power ON/OFF
Press and hold the ON/OFF button for 2-3 seconds to switch the headset on. The
LED will flash blue when powered on. Press and hold the ON/OFF button for 3
seconds to switch the headset off. When powering off, the LED will flash blue
and then turn off indicating the headset is off.
Pairing
While the headset is off, press and hold the ON/OFF – for 2-3 seconds to start
pairing mode. Once the headset is in the pairing mode (the LED will flash red
and blue), select
‘H50’ among discovered Bluetooth devices on the phone to Pair.
Note: If the headset is not paired with a Bluetooth device in 3 minutes,
it will turn itself off.
Making Phone Calls
Making a call
Once paired, use your mobile device to dial a number as usual. Once connected,
the call will be heard on your H50 headset.
Last number redial
Press the ON/OFF button to redial last number.
Note: For some mobile models, press the ON/OFF button twice.
Answer a call
When receiving a call, press the ON/OFF button to answer the call.
Ending a call
While talking on the phone, press the ON/OFF button to end the call.
Listening to Music
Play/Pause
Press the Play button to launch the phone’s music player and to start
listening to music. While listening to music, press the Pause button to pause
or to resume play.
Song selection
While music is playing, press the |+| or |-| buttons to skip or go to previous
songs.
Answer a call while listening to music
When receiving a call, press the ON/OFF button to answer the call. Press the
ON/OFF button while on the phone to end the call. When receiving a call, press
and hold the ON/OFF button to reject the call. (Music will resume playing when
the call is rejected.)
Volume control
Press and hold Volume |+| and Volume |-| buttons to adjust the volume level.
Compliance with FCC Regulations
Caution!
The user is cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment. The equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate Radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to Radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to Radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from which the receiver is connected.
- Consult the dealer or an experienced Radio/television technician for assistance.
This equipment complies with FCC’s RF radiation exposure limits set forth for
an uncontrolled environment. The antenna(s) used for this transmitter must be
installed and operated to provide a separation distance of at least 20 cm from
all persons and must not be collocated or operating in conjunction with any
other antenna or transmitter. Installers must ensure that 20 cm separation
distance will be maintained between the device (excluding its handset) and
users.
THE SPECIFICATION AND EXTERNAL APPEARANCE OF THE HEADPHONES ARE SUBJECT TO
CHANGE WITHOUT PRIOR NOTICE.
- If at any time in the future you should need to dispose of this product, please note that waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Warranty Information
Limited Warranty
The AT&T brands are used under license. Any repair, replacement, or warranty
service, and all questions about this product should be directed to Concept
101 LLC at www.att.com/electronics or call 1
888-920-8680 from the USA or Canada.
Concept 101 LLC warrants to the original purchaser that the product will be
free from defects in material, parts and workmanship for the period designated
for this product. The warranty commences the day the product is purchased and
covers up to a period of one (1) year. Concept 101 LLC agrees that it will, at
its option, replace the defective product with either a new or remanufactured
headset equivalent to your original purchase during the warranty period.
Should the Parts warranty period exceed the Labor warranty period, Concept 101
LLC will supply at no charge for the remainder of the Parts warranty, any new
or remanufactured replacement parts as required by the product. During this
period all labor and service charges will become the responsibility of the
customer.
Exclusions: This warranty does not apply to the appearance or exterior of
the product which may have been damaged or defaced, altered or modified in
design or construction. This warranty does not apply if the serial number is
altered or removed, or if there is any damage due to power line surge, user
damage to the AC power cord, connection to improper voltage source, general
misuse, accidents, or repair attempts by unauthorized service agents. Other
exclusions include ear pads, rechargeable and non-rechargeable batteries.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CUSTOMER; Concept 101 LLC SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED TO THE DURATION OF THE WARRANTY.
Some states do not allow the exclusion or limitations of incidental or
consequential damages, or limitations on how long the warranty lasts. In these
cases the above exclusions or limitations may not apply to you. This warranty
gives you specific legal rights and you may also have other rights which vary
from state to state.
Obtaining Service: To obtain service, product literature, supplies or
accessories please call 1 888-920-8680,
or visit our website,
www.att.com/electronics, to create a ticket
for exchange/repair. Please make sure to provide the date of purchase, model
number and a brief description of the problem. Our customer service
representative will contact you or send detailed return instructions.
Concept 101 LLC does not warrant that the headset will work properly in all
environmental conditions, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose other than the purpose
identified within this user’s manual. Concept 101 LLC has made every effort to
ensure that this user’s manual is accurate and disclaims liability for any
inaccuracies or omissions that may have occurred. Information in this user’s
manual is subject to change without notice and does not represent a commitment
on the part of Concept 101 LLC. Concept 101 LLC reserves the right to make
improvements to this user’s manual and/or to the products described in this
user’s manual at any time without notice. If you find information in this
manual that is incorrect, misleading, or incomplete, please contact us through
our website.
Specifications
- Bluetooth – 5.0
- Charging time – approximately 2 hours
- Battery – 3.7V 200Mah
- Playback Time – up to 4 hours
- Up to 30 ft. wireless range as determined by Bluetooth SIG. Range may vary depending on the line of sight obstacles.
Memo
Purchase date:
Place of purchase:
www.att.com/electronics
© 2019 Concept 101 LLC. All Rights Reserved. AT&T and the AT&T logo are
trademarks of AT&T Intellectual Property licensed to Concept 101 LLC, New
York, New York 10018. Printed in China. Issue 1.1 AT&T 4/2019.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. Other trademarks and trade names are those of their
respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>