boAt ROCKERZ 255 Max In Ear Earphones User Manual

boAt ROCKERZ 255 Max In Ear Earphones

PACKAGE CONTENTS

1. 1x Rockerz 255 Max
2. 1x Manual
3. 1x Warranty Card
4. 1× USB Type C charging cable
5. 1x Catalogue
6. 1× Pairs of additional earmuffs (Small & Large)

OVERVIEW

TO PAIR WITH BLUETOOTH

1. When switched off, separate the left and right earbuds to switch on the wireless neckband and put them into pairing mode. The earphones automatically enter pairing mode with white and red LED flashes alternatively to indicate the same.
2. Open the Bluetooth functionality on your media device and search for “Rockerz 255 Max” from the list of available devices.
3. Choose “Rockerz 255 Max” from the list and if asked for a passcode, enter the pairing code “0000” to establish Bluetooth connectivity.
4. Once successfully connected, the white LED flashes once every 5 seconds to indicate the same
   • Note: The wireless neckband automatically turns off if there is no pairing established in 5 minutes.

FUNCTIONALITIES

1. Power On: When switched off, separate both earbuds from each other. White LED flashes to indicate the same.
2. Power Off: In a powered-on state, unite both the earbuds together. Red LED flashes to indicate the same.
3. Play/Pause: Short press the MB (Multi-function Button) to play/pause music at your convenience.
4. Volume Up: Short press the Volume Up “+” button in steps to increase the volume. A voice prompt indicates maximum volume.
5. Volume Down: Short press the Volume Down “-” button in steps to decrease the volume.
6. Answer/End call: Short press the MFB once when answering or ending a call to complete the action.
7. Reject call: Press and hold the MB for 2 seconds during an incoming call to reject the call.
8. Previous Track: To go back to the previous track or start the track from the beginning, press and hold the Volume Down “.* button for 2 seconds.
9. Next Track: To skip to the next track, press and hold the Volume Up “*” button for 2 seconds.
10. EQ Modes: Double press the MB to switch among the EQ modes, viz., Signature Mode (Bass-centric); Pop Mode, and Balanced Mode.
11. Reset Device (Clear Paired List): Press and hold the Volume Up and Volume Down buttons simultaneously for 5 seconds to clear the list of paired devices. The white LED stays on for 2 seconds to indicate the same.
12. Dual Pairing: To connect Rocker 255 Max to two devices simultaneously, first connect the earphones to one of the devices. Then, switch off the device’s Bluetooth. Thereafter, connect the earphone to the second device, and again switch on the first device’s Bluetooth. The earphone gets connected to both devices. if not, connect the first device manually once again to activate dual pairing.
13. BEAST Mode: Triple press the MB to switch to Low Latency mode, also known as the BEAST Mode. Once switched on, it gets notified via a sound prompt. Triple-press the MB again to turn it off and return to normal music mode.
    • Made for the Gamers – By Gamers, BEAST’™ Mode reduces the latency significantly and improves the overall gaming experience.
    • ENx”™ Tech: Our ENx™ tech algorithm cancels out the background noise so that you can be heard crystal clear via voice calls. One need not activate ENx™ as the mic is equipped with the same and activated by default.
    • Deliver your voice without interruptions anywhere – traffic, railway stations, airports, workspace; literally anywhere!
14. Voice Assistant: Long press the MFB for 2 seconds to wake up smart voice assistant.
    • Note: If the voice assistant doesn’t get triggered then the functionality has to be first enabled by your media device.

TO CHARGE

Use the provided USB Type C charging cable to charge the earphones through either laptop/adaptor/power bank.

1. Low Battery: When the remaining battery is below 10%, there is a ‘Battery Low’ prompt every few minutes and a red LED quickly flashes to indicate the same.
2. Charging: A solid red LED indicates that the earphone is being charged (please note that the earphone cannot / should not be turned on while charging).
3. Fully charged: Solid white LED indicates the same.

SPECIFICATIONS

FCC Warning

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
• The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Rockerz 255 Max FCC ID: 2BARQ-R255MAX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>