Prestel SW-4K41MVS 4K60 4×1 Multiviewer Seamless UHD Video Switcher User Manual
- June 13, 2024
- Prestel
Table of Contents
Prestel SW-4K41MVS
4K60 4×1 Multiviewer Seamless UHD
Video Switcher
USER MANUAL
Thank you for purchasing this product
For optimum performance and safety, please read these instructions carefully
before connecting, operating or adjusting this product. Please keep this
manual for future reference.
Surge protection device recommended
This product contains sensitive electrical components that may be damaged by
electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge
protection systems is highly recommended in order to protect and extend the
life of your equipment.
Introduction
This 4K60 4×1 Multiviewer Seamless UHD Video Switcher was developed for the
purpose of supporting higher output resolution (4K@60) for multiple sources on
a single screen. It can combine up to four video signals onto a single UHD or
HD displayer. The user can easily manage each input via the supplied Control
Software and create any layout and position of any of the four inputs on a
single monitor.
This device supports full range of input video resolutions up to 4K@60 (RB)
and audio RCA /Optical de-embedding supported for external audio distribution
systems.
This device can be controlled via front panel buttons, IR remote, RS-232
commands.
Features
- HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
- Support 18Gbps video bandwidth
- Input and output resolutions support up to 4K@60Hz
- Support LPCM, AC3, DD+, DTS, DTS-HD, up to 7.1 audio channel
- Seamless switching between input channels and combined multiple images on single UHD monitor
- Up to 8 display modes: SINGLE, PIP, PBP (1), PBP (2), Triple (1), Triple (2), Quad (1), Quad (2)
- Seamless switching on single screen display mode
- Fast switching on multiview display mode
- Audio de-embedding via analog and optical fiber audio ports
- Support volume control and independent audio selection
- Support OSD navigation for advanced setting
- EDID management
- Control via front panel buttons, IR remote, RS-232 commands
- Compact design for easy and flexible installation
Package Contents
- 1 x 4K60 4×1 Multiviewer Seamless UHD Video Switcher
- 1 x IR Remote
- 1 x 3pin-3.81mm Phoenix Connector (male)
- 1 x 38KHz IR Wideband Receiver Cable (1.5 meters)
- 2 x Mounting Ears
- 4 x Machine Screws (KM3*4)
- 4 x Rubber Feet
- 1 x 12V/2.5A Locking Power Adapter
- 1 x User Manual
Specifications
Technical
HDMI Compliance| HDMI 2.0b
HDCP Compliance| HDCP 2.2 / 1.x
Video Bandwidth| 18Gbps
Video Resolution| Up to 4K@60Hz
IR Level| 5Vp-p
IR Frequency| 38KHz
Color Space| RGB, YCbCr 4:4:4, YCbCr 4:2:2, YCbCr 4:2:0
Color Depth| 8bit
** Audio Formats| HDMI: PCM2.0/5.1/7.1CH, Dolby Digital/Plus, DTS, DTS
High Res
Analog audio [3.5mm L/R]: PCM2.0;
SPDIF (OPTICAL): Dolby Digital, DTS 5.1, PCM2.0.
Note: It does not support HBR audio.
ESD Protection| Human body model — ±8kV (Air-gap discharge) & ±4kV (Contact
discharge)
Connection**
Input ports| 4 x HDMI IN [Type A, 19-pin female]
Output ports
| 1 x HDMI OUT [Type A, 19-pin female] 1 x L/R OUTPUT [RCA]
1 x OPTICAL OUTPUT [S/PDIF]
Control ports| 1 x RS-232 [3pin-3.81mm phoenix connector] 1 x IR EXT [3.5mm
Stereo Mini-jack]
Mechanical
Housing| Metal Enclosure
Color| Black
Dimensions| 220mm [W] x 100mm [D] x 30mm [H]
Weight| 620g
Power Supply| Input: AC 100 – 240V 50/60Hz
Output: DC 12V/2.5A (US/EU standard, CE/FCC/UL certified)
Power Consumption| 10W (Max)
Operating
Temperature
| 32 – 104°F / 0 – 40°C
Storage Temperature| -4 – 140°F / -20 – 60°C
Relative Humidity| 20 – 90% RH (no-condensing)
Operation Controls and Functions
5.1 Front Panel
No. | Name | Function Description |
---|---|---|
**** 1 | **** Power button | ▪ Short press this button to power on the device. |
▪ Long press this button for 1 seconds to enter the standby mode.
2| Power LED| The Power LED will light in green when the product is powered
on, and red when the product is on standby.
**** 3| ** Input 1-4 LEDs| Input signal indicator lights. When the HD
1/2/3/4 port connects an active source device, the corresponding green LED
will be on.
Note: Only the LED of the selected input channel will light in green on
single screen display mode; all LEDs will light in green on multiview mode.
** 4| AUTO LED| When the device is on the AUTO mode, the AUTO LED
will light in green, and HDMI is automatically identified, that is, when the
currently displayed source signal is disconnected, the switcher will
automatically identify the next connected HDMI input port.
5| IR Window| IR signal receiving window.
6| AUTO button| Automatic switching button, only available on single screen
display mode.
7| INPUT button| Input source switching button, only available on single
screen display mode.
**** 8| **** Multiview button| Multiview display mode switching
button.
▪ Short press this button to circularly select: SINGLE – PIP – PBP (1) – PBP
(2) – Triple (1) – Triple (2) – Quad (1) – Quad (2).
▪ Long press this button for 3 seconds to select the aspect ratio for PBP (1)
/ PBP (2) / Triple (1) / Triple (2) / Quad (1) / Quad (2).
9| RES button| Output resolution switching button.
▪ Short press the RES button to circularly switch the output resolution of
the HDMI OUTPUT port (Please refer to the output resolution list of “8. Video
& Audio”).
▪ Long press the RES button for 3 seconds to switch the output resolution
to 720P60.
5.2 Rear Panel
No. | Name | Function Description |
---|---|---|
1 | L/R port | PCM2.0 Analog audio output port. |
2 | OPTICAL port | Optical fiber digital audio output port. |
3 | HDMI OUTPUT port | HDMI signal output port, connected to HDMI display device |
such as TV or Monitor with HDMI cable.
4| HD 1-4 INPUT ports| HDMI signal input ports, connected to HDMI source
device such as DVD or Set-top box with HDMI cable.
5| RS-232 port| 3-pin phoenix connector, connected to a PC or control system
for serial port upgrade or RS-232 command control.
6| IR EXT port| IR signal receiving port, connected with 38KHz IR
Receiver cable.
If the IR signal receiving window of the unit is blocked or the unit is
installed in a closed area out of infrared line of sight, the IR receiver
cable can be inserted to the “IR EXT” port to receive the IR remote signal.
7| DC 12V| DC 12V/2.5A power input port.
IR Remote
-
Power on or Standby: Press this button to power on the switcher or set it to standby mode.
-
HD 1/2/3/4: Press these buttons to select input source on single screen display mode, and the corresponding input LED on the front panel will light in green.
: Press these buttons to circularly select the last or next input source on single screen display mode.
: Multiview display mode switching button.
▪ Short press this button to circularly select: SINGLE – PIP – PBP (1) PBP (2) – Triple (1) – Triple (2) – Quad (1) – Quad (2).
▪ Long press this button for 3 seconds to select the aspect ratio for PBP (1) / PBP (2) / Triple (1) / Triple (2) / Quad (1) / Quad (2).
: Output resolution switching button.
▪ Short press the RES button to circularly switch the output resolution of the HDMI OUTPUT port (Please refer to the output resolution list of “8. Video & Audio”).
▪ Long press the RES button for 3 seconds to switch the output resolution to 720P60. -
MENU, EXIT, LEFT, RIGHT, UP, DOWN, OK: OSD Menu navigation buttons.
-
A-IN: Press this button to pop up the audio channel selection OSD, then press the UP / DOWN button to select the audio output channel. (The output audio follows the video source by default.)
Mute: Press this button to mute / unmute the audio.
VOL-, VOL+: Press these buttons to increase / decrease the audio output volume.
EDID Settings
User can select following EDID modes via RS-232 command or OSD menu navigation.
No. | EDID Mode | No. | EDID Mode |
---|---|---|---|
1 | 4K60-2.0CH | 10 | 1920×1200-2.0CH |
2 | 4K60-5.1CH | 11 | 1680×1050-2.0CH |
3 | 4K60-7.1CH | 12 | 1600×1200-2.0CH |
4 | 4K30-2.0CH | 13 | 1440×900-2.0CH |
5 | 4K30-5.1CH | 14 | 1360×768-2.0CH |
6 | 4K30-7.1CH | 15 | 1280×1024-2.0CH |
7 | 1080P-2.0CH | 16 | 1024×768-2.0CH |
8 | 1080P-5.1CH | 17 | 720P-2.0CH |
9 | 1080P-7.1CH | 18 | AUTO |
Video & Audio
The switcher supports multiple resolution video input up to 3840×2160@60, and
supports multiple audio formats such as LPCM, AC3, DD+, DTS, DTSHD, up to 7.1
channel pass through function via HDMI cable.
User can control the volume of audio in LPCM format. The switcher supports
following video output resolutions via a powerful scaling engine.
No. | Output Resolution | No. | Output Resolution |
---|---|---|---|
1 | 4096x2160p 60Hz | 8 | 1920x1080p 60Hz |
2 | 4096x2160p 50Hz | 9 | 1920x1080p 50Hz |
3 | 3840x2160p 60Hz | 10 | 1360x768p 60Hz |
4 | 3840x2160p 50Hz | 11 | 1280x800p 60Hz |
5 | 3840x2160p 30Hz | 12 | 1280x720p 60Hz |
6 | 3840x2160p 25Hz | 13 | 1280x720p 50Hz |
7 | 1920x1200p 60Hz RB | 14 | 1024×768 60Hz |
Multiview
The switcher supports 8 categories of multiview display modes: SINGLE, PIP,
PBP (1), PBP (2), Triple (1), Triple (2), Quad (1), Quad (2) Users can select
different operations for different Multiview modes as following:
SINGLE: Inputs selection
PIP: Inputs selection, Sub window size and position selection
PBP (1), PBP (2), Triple (1), Triple (2), Quad (1), Quad (2): Inputs
selection, Display mode selection, Display aspect selection
Multiview window distributions are as following:
User can select Multiview modes via RS-232 commands or OSD menu navigation.
OSD Menu Navigation
- A total of seven buttons on the IR Remote are used for OSD menu navigation, including MENU, EXIT, UP, DOWN, LEFT, RIGHT, OK. Menu contents are as follows:
Output
|
Resolution
|
3840x2160p60
| 4096x2160p 60Hz/
4096x2160p 50Hz/
3840x2160p 60Hz/
3840x2160p 50Hz/
3840x2160p 30Hz/
3840x2160p 25Hz/
1920x1200p60Hz RB/
1920x1080p 60Hz/
1920x1080p 50Hz/
1360x768p 60Hz/
1280x800p 60Hz/
1280x720p 60Hz/
1280x720p 50Hz/
1024×768 60Hz
---|---|---|---
VKA
|
BLACKSCREEN,
| BLACKSCREEN, BLUESCREEN
ITC| OFF| ON,OFF
Multiview
| Single| Input select| HDMI1,HDMI2,HDMI3,HDMI4
PIP
| Win1 Select| HDMI1,HDMI2,HDMI3,HDMI4
Win2 Select| HDMI1,HDMI2,HDMI3,HDMI4
PIP Position
| Right Bottom,Right Top, Left Bottom,Left Top
PIP Size| Small,Middle,Large
PBP
| Win1 Select| HDMI1,HDMI2,HDMI3,HDMI4
Win2 Select| HDMI1,HDMI2,HDMI3,HDMI4
MODE| 1, 2
Aspect| Full, 16:9
|
3xWIN
| Win1 Select| HDMI1,HDMI2,HDMI3,HDMI4
---|---|---|---
Win2 Select| HDMI1,HDMI2,HDMI3,HDMI4
Win3 Select| HDMI1,HDMI2,HDMI3,HDMI4
MODE| 1, 2
Aspect| Full, 16:9
4xWIN
| Win1 Select| HDMI1,HDMI2,HDMI3,HDMI4
Win2 Select| HDMI1,HDMI2,HDMI3,HDMI4
Win3 Select| HDMI1,HDMI2,HDMI3,HDMI4
Win4 Select| HDMI1,HDMI2,HDMI3,HDMI4
MODE| 1, 2
Aspect| Full,16:9
AUDIO
|
Audio Select
| WIN1| WIN1,HDMI1,HDMI2,HDMI3, HDMI4
Volume| 100| 0..100
AUDIO-MUTE| OFF| ON, OFF
System
| Language/语言| 中文| English, 中文
EDID
|
4K60-2.0
| 4K60-2.0,4K60-5.1CH,
4K60-7.1CH,4K30-2.0CH,
4K30-5.1CH,4K30-7.1CH,
1080P-2.0CH,1080P-5.1CH,
1080P-7.1CH,1920×1200-
2.0CH,1680×1050-2.0CH,
1600×1200-2.0CH,1440×900
-2.0CH, 1360×768-2.0CH, 1280×1024-2.0CH, 1024x
768-2.0CH,720P-2.0CH, AUTO
Baud rate| 115200| 115200,57600,38400, 19200,9600
Reset| Reset| Reset
FW Version| | Read only
2. A total of four buttons on the IR Remote are used for audio setting on OSD menu navigation, including A-IN, Mute, VOL-, VOL+.
Menu contents are as follows:
A-IN
|
Audio Input
|
WIN1
| WIN1,HDMI1,HDMI2,HDMI3, HDMI4
---|---|---|---
Mute| Audio Mute| OFF| ON, OFF
VOL-/VOL+| Audio Volume| 100| 0..100
RS-232 Command
The product also supports RS-232 command control. Connect the RS-232 port of the product to a PC with a 3-pin phoenix connector cable. Then, open a Serial Command tool on PC to send ASCII commands to control the product. The ASCII command list about the product is shown as below.
ASCII Commands
Serial port protocol. Baud rate: 115200 (default), 57600, 38400, 19200, 9600; Data bits: 8bit;
Stop bits:1; Check bit: 0
x – Parameter 1; y – Parameter 2; ! – Delimiter
Command Code| Function Description| Example| Feedback
System Setting| | |
help!| List all commands| help!|
r type!| Get device model| r type!| 4×1 HDMI Multiviewer
r fw version!| Get Firmware version| r fw version!| MCU FW version x.xx.xx
SCALER FW version x.xx.xx
power z!
|
Power on/off the device,z=0~1 (z=0 power off, z=1 power on)
|
power 1!
| Power on
System Initializing… Initialization Finished! MCU FW version x.xx.xxSCALER FW
version x.xx.xx
r power!| Get current power state| r power!| power on/power off
reboot!
|
Reboot the device
|
reboot!
| Reboot…
System Initializing… Initialization Finished! MCU FW
ersion x.xx.xx
SCALER FW version x.xx.xx
Command Code| Function Description| Example| Feedback
---|---|---|---
reset!
|
Reset to factory defaults
|
reset!
| Reset to factory defaults
System Initializing… Initialization Finished! MCU FW version x.xx.xx
SCALER FW version x.xx.xx
Output Setting| | |
s output res x!
| Set Output Resolution (x=1~14)
1. 4096x2160p60,
2. 4096x2160p50,
3. 3840x2160p60,
4. 3840x2160p50,
5. 3840x2160p30,
6. 3840x2160p25,
7. 1920x1200p60RB,
8. 1920x1080p60,
9. 1920x1080p50,
10.1360x768p60,
11.1280x800p60,
12.1280x720p60,
13.1280x720p50,
14. 1024x768p60,
|
s output res 3!
|
out resolution: 3840x2160p60
r output res!| Get output resolution| r output res!| out resolution: 3840x2160p60
s output hdcp x!
| set output hdcp (x=1~3)
1. HDCP 1.4
2. HDCP 2.2
3. HDCP OFF
|
s output hdcp 2!
|
output HDCP: HDCP 1.4
r output hdcp!| Get output hdcp status.| r output hdcp!| output HDCP: HDCP 1.4
s output vka x!
| Set output video keep active pattern. (x=1~2)
1. black screen
2. blue screen
|
s output vka 1!
|
output VKA pattern: black screen
r output vka!| Get output video keep active pattern.| r output vka!| output VKA pattern: black screen
s output itc x!
| Set output video mode (x=1~2) 1: video mode
2: pc mode
|
s output itc 1!
|
output ITC: video mode
r output itc!| Get output video mode| r output itc!| output ITC: video mode
Command Code| Function Description| Example| Feedback
---|---|---|---
EDID Setting
s input EDID x!
| Set HDMI input EDID mode (x=18)
1. 4K2K60_444,Stereo Audio 2.0 2. 4K2K60_444,Dolby/DTS 5.1 3. 4K2K60_444,HD Audio 7.1
4. 4K2K30_444,Stereo Audio 2.0 5. 4K2K30_444,Dolby/DTS 5.1 6. 4K2K30_444,HD Audio 7.1
7. 1080P,Stereo Audio 2.0
8. 1080P,Dolby/DTS 5.1
9. 1080P,HD Audio 7.1 10.1920×1200,Stereo Audio 2.0 11.1680×1050,Stereo Audio 2.0 12.1600×1200,Stereo Audio 2.0 13.1440×900,Stereo Audio 2.0 14.1360×768, Stereo Audio 2.0 15.1280×1024,Stereo Audio 2.0 16.1024×768, Stereo Audio 2.0 17.720p,Stereo Audio 2.0 18.copy from HDMI out
|
s input EDID 1!
|
input EDID:4K2K60_444, Stereo Audio 2.0
r input EDID!| Get input EDID mode| r input EDID!| input EDID:4K2K60_444,
Stereo Audio 2.0
Audio Setting| | |
s output audio x!
| Set output audio source (x=0~4)
0. follow window 1 selected source
1. HDMI 1 input audio
2. HDMI 2 input audio
3. HDMI 3 input audio
4. HDMI 4 input audio
|
s output audio 0!
|
output audio: follow window 1 selected source
r output audio!| Get output audio source| r output audio!| output audio:
follow window 1 video
s output audio vol+!| Increase output audio volume| s output audio vol+!|
output audio volume: 50
s output audio vol-!| Decrease output audio volume| s output audio vol-!|
output audio volume: 50
s output audio vol x!| Set output audio volume value (x=0~100)| s output audio
vol 30!| output audio volume: 30
r output audio vol!| Get output audio volume| r output audio vol!| output
audio volume: 30
s output audio mute x!
| Set output audio mute on/off (x=0~1)
0. mute off
1. mute on
|
s output audio mute 0!
|
output audio mute: off
Command Code | Function Description | Example | Feedback |
---|---|---|---|
r output audio mute! | Get output audio mute on/off | r output audio mute! |
output audio mute: off
Single Screen Mode Setting| |
s auto switch x!
| Enable/disable auto switch feature(x=0~1)
0. Disable auto switch
1. Enable auto switch
|
s auto switch 0!
|
auto switch off
r auto switch!| Get auto switch feature| r auto switch!| auto switch off
s in source x!
| Route input source to output (1~4)
1. HDMI 1
2. HDMI 2
3. HDMI 3
4. HDMI 4
|
s in source 1!
|
HDMI 1
r in source!| Get output selected input source| r in source!| HDMI 1
Multi-viewer Mode Setting| |
s multiview x!
| Set multi-viewer display mode (x=1~5)
1. single screen
2. PIP
3. PBP
4. triple screen
5. quad screen
|
s multiview 1!
|
single screen
r multiview!| Get multi-viewer display mode| r multiview!| single screen
s window x in y!
| Select one input for one display window for the current Multiview mode.
(x=1~4)
1. window 1
2. window 2
3. window 3
4. window 4 (y=1~4)
1. HDMI 1
2. HDMI 2
3. HDMI 3
4. HDMI 4
|
s window 1 in 1!
|
window 1 select HDMI 1
Command Code | Function Description | Example | Feedback |
---|
r window x in!
| Get windows selected input source (x=0~4)
0. ALL
1. window 1
2. window 2
3. window 3
4. window 4
|
r window 1 in!
|
window 1 select HDMI 1
s PIP position x!
| Set PIP window position (x=1~4)
1. Left Top
2. Left Bottom
3. Right Top
4. Right Bottom
|
s PIP position 3!
|
PIP on right top
r PIP position!| Get PIP window position| r PIP position!| PIP on right top
s PIP size x!
| Get PIP window size (x=1~3)
1. small
2. middle
3. large
|
s PIP size 3!
|
PIP size: large
r PIP size!| Get PIP window size| r PIP size!| PIP size: large
s PBP mode x!
| Set PBP windows display mode (x=1~2)
1. PBP mode 1
2. PBP mode 2
|
s PBP mode 1!
|
PBP mode 1
r PBP mode!| Get PBP windows display mode| r PBP mode!| PBP mode 1
s PBP aspect x!
| Set PBP windows display aspect ratio (x=1~2)
1. Full screen 2. 16:9
|
s PBP aspect 1!
|
PBP aspect: full screen
r PBP aspect!| Get PBP windows display
aspect ratio
| r PBP aspect!| PBP aspect: full screen
s triple mode x!
| Set triple windows display mode (x=1~2)
1. triple mode 1
2. triple mode 2
|
s triple mode 1!
|
triple mode 1
r triple mode!| Get triple windows display mode| r triple mode!| triple mode 1
s triple aspect x!
| Set triple windows display aspect ratio (x=1~2)
1. Full screen
2. 16:9
|
s triple aspect 1!
|
triple aspect: full screen
r triple aspect!| Get triple windows display aspect ratio| r triple aspect!| triple aspect: full screen
s quad mode x!
| Set quad windows display mode (x=1~2)
1. quad mode 1
2. quad mode 2
|
s quad mode 1!
|
quad mode 1
Command Code | Function Description | Example | Feedback |
---|---|---|---|
r quad mode! | Get quad windows display mode | r quad mode! | quad mode 1 |
s quad aspect x!
| Set quad windows display aspect ratio (x=1~2)
1. Full screen
2. 16:9
|
s quad aspect 1!
|
quad aspect: full screen
r quad aspect!| Get quad windows display aspect ratio| r quad aspect!| quad aspect: full screen
Application Example
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>