Prestel SW-4K21MVS 4K60 2×1 Multiviewer Seamless UHD Video Switcher User Manual

Prestel SW-4K21MVS 4K60 2x1 Multiviewer Seamless UHD Video Switcher User Manual

Thank you for purchasing this product
For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.

Surge protection device recommended
This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment.

Introduction

This 4K60 2×1 Multiviewer Seamless UHD Video Switcher was developed for the purpose of supporting higher output resolution (4K@60) for multiple sources on a single screen. It can combine two video signals onto a single UHD or HD displayer. The user can easily manage each input via the supplied Control Software and create any layout and position of any of the two inputs on a single monitor.
This device supports full range of input video resolutions up to 4K@60 (RB) and audio RCA /Optical de-embedding supported for external audio distribution systems.
This device can be controlled via front panel buttons, IR remote, RS-232 commands.

Features

• HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
• Support 18Gbps video bandwidth
• Input and output resolutions support up to 4K2K@60 4:4:4
• Support LPCM, AC3, DD+, DTS, DTS-HD, up to 7.1 audio channel
• Seamless switching between input channels and combined multiple images on single UHD monitor
• Up to 4 display modes: SINGLE, PIP, PBP (1), PBP (2)
• Audio de-embedding via analog and optical fiber audio ports
• Support volume control and independent audio selection
• Advanced EDID management
• Control via front panel buttons, IR remote, RS-232 commands
• Compact design for easy and flexible installation

Package Contents

1. 1 x 4K60 2×1 Multiviewer Seamless UHD Video Switcher
2. 1 x IR Remote
3. 1 x 3pin-3.81mm Phoenix Connector (male)
4. 1 x 38KHz IR Wideband Receiver Cable (1.5 meters)
5. 2 x Mounting Ears
6. 4 x Machine Screws (KM3*4)
7. 1 x 12V/1A Locking Power Adapter
8. 1 x User Manual

Specifications

Operation Controls and Functions

5.1 Front Panel

5.2 Rear Panel

IR Remote

1. Power on or Standby: Press this button to power on the switcher or set it to standby mode.

2. Baud: Press this button to pop up OSD menu, then circularly select the serial port baud rate: 115200, 57600, 38400, 19200, 9600

3. Multiview display mode buttons: Press these buttons to select the display
   mode: SINGLE – PIP – PBP (1) – PBP (2).

4. WIN1: These buttons are available in all modes.
   On single screen display mode, press HD1/HD2/ button to directly /circularly selcet input source for the WIN1 screen, and the corresponding input LED on the front panel will light in green.
   On PIP / PBP(1) / PBP(2) display mode, press HD1/HD2/ button to directly/ circularly selcet input source for the WIN1 screen, and both input LEDs on the front panel will light in green.

5. WIN2: These buttons are unavailable on single screen display mode.
   On PIP / PBP(1) / PBP(2) mode, press HD1/HD2/ button to directly/ circularly selcet input source for the WIN2 screen, and both input LEDs on the front panel will light in green.

6. SET:
   On PIP mode, press POS to change the position of sub window ; press SIZE to zoom in / out the size of sub window.
   On PBP(1) / PBP(2) mode, press 16:9 to switch the aspect ratio between 16:9 and FULL.

7. AUDIO: Press Mute to mute / unmute the audio output; Press VOL- / VOL+ to increase / decrease the audio output volume.

8. Resolution: Press 4K, 1080P, 720P or XGA to select output resolution.

9. EDID: Press 4K2.0, 4K5.1, 2K2.0 or COPY to select EDID mode.

EDID Settings

User can select following EDID modes via RS-232 commands.

Video & Audio

The switcher supports multiple resolution video input up to 3840×2160@60, and supports multiple audio formats such as LPCM, AC3, DD+, DTS, DTS-HD, up to 7.1 channel pass through function via HDMI cable.
User can control the volume of audio in LPCM format.
The switcher supports following video output resolutions via a powerful scaling engine.

Multiview

The switcher supports 4 categories of multiview display modes:
SINGLE, PIP, PBP (1), PBP (2)
Users can select different operations for different Multiview modes as following:
SINGLE: Inputs selection
PIP: Inputs selection, Sub window size and position selection
PBP (1), PBP (2): Inputs selection,
Display mode selection, Display aspect selection
Multiview window distributions are as following:

User can select Multiview modes via IR remote or RS-232 commands.

OSD Menu Navigation

A total of four buttons on the IR Remote are used for audio setting on OSD menu navigation, including Baud, Mute, VOL-, VOL+.
Menu contents are as follows:

RS-232 Command

The product also supports RS-232 command control. Connect the RS-232 port of the product to a PC with a 3-pin phoenix connector cable. Then open a Serial Command tool on PC to send ASCII commands to control the product.
The ASCII command list about the product is shown as below.

Application Example

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>