Indesit IWC71452 Washing Machine Instruction Manual

Indesit IWC71452 Washing Machine Instruction Manual

Installation

• Keep this instruction manual in a safe place for future reference.
• Should the appliance be sold, transferred, or moved, ensure the instruction manual accompanies the washing machine to inform the new owner of its operation and features.
• Please read these instructions carefully: they contain vital installation, use, and safety information.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.
2. Check whether the washing machine has been damaged during transport. If this is the case, do not install it and contact your retailer.
3. Remove the 4 protective screws and the rubber bush with the respective spacer, situated on the rear of the appliance (see also the installation leaflet).
4. Seal the gaps using the plastic plugs provided.
5. keep all the parts: you will need them again if the washing machine needs to be moved to another location.
6. Packaging materials are not children’s toys.

Levelling
Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly.

1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or others.
2. If the floor is not per-fectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measu-red according to the worktop, must not exceed 2°.
3. Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation.
4. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washing machine.

Electric and water connections

Connecting the water inlet hose

1. Connect the supply pipe by screwing it to a cold water tap using a 3/4 gas threaded connection (see figure). Before performing the connection, allow the water to run freely until it is perfectly clear.
2. Connect the other end of the water inlet hose to the washing machine, screwing it onto the appliance’s cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure).
3. Make sure there are no kinks or bends in the hose.
   • The water pressure at the tap must be within the values indicated in the Technical details table (on page 5).
   • If the water inlet hose is not long enough, contact a specialist store or an authorised serviceman.
   • Ensure that the supply taps are allowing water through. Old taps may seize in the closed position and thus prevent water from reaching the machine.

Connecting the drain hose

• Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;
• The drain hose may be connected to an under-sink trap. Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot.
• If it is placed over the edge of a basin or sink be sure the free end of the hose should not be underwater.
• We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.
• Ensure that if the drain hose is pushed into a standpipe, that the end does not go down more than 15 cm (6 inches). If the hose is pushed down too far, this may cause the machine to self -syphon ie. continuously empty as it is filling.

Electric connection
Before plugging the appliance into the mains socket, make sure that:

• the socket is earthed and in compliance with the applicable law;
• the socket is able to sustain the appliance’s maximum power load indicated on the Technical Data Plate fixed on the machine;
• the supply voltage is included within the values indicated on the Technical Data Plate fixed on the machine.
• the socket is compatible with the washing machine’s plug. If this is not the case, replace the socket or the plug.
• Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING
THIS APPLIANCE MUST BE EARTHED. THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse
When replacing a faulty fuse, a 13 amp ASTA-approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers
If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot.

Removing the plug
If your appliance has a non-rewireable moulded plug and you wish to re-route the mains cable through partitions, units etc., please ensure that either: the plug is replaced by a fused 13-ampere rewireable plug bearing the BSI mark of approval. or: the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS 5733) which is accessible without moving the appliance.

Disposing of the plug
Ensure that before disposing of the plug itself, you make the pins unusable so that they cannot be accidentally inserted into a socket.

Instructions for connecting the cable to an alternative plug
Important: the wires in the mains lead are co-loured in accordance with the following code:

• Green & Yellow Earth
• Blue Neutral
• Brown Live

As the colours of the wires in the lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Connect Green and yellow wire to the terminal marked E or coloured Green or Green and yellow. Connect the Brown wire to the terminal marked L or coloured Red. Connect Blue wire to the terminal marked N or co-loured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board. If you are in any doubt regarding the electrical supply to your machine, consult a qualified electrician before use.

How to connect an alternative plug
The wires in this mains lead are coloured in accordance with the following code:

• BLUE
• BROWN
• GREEN & YELLOW
• NEUTRAL (N)
• LIVE (L)
• EARTH (E)

Disposing of the appliance
When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above.

• The washing machine should not be installed in an outdoor environment, not even where the area is sheltered, because it may be very dangerous to leave it exposed to damp, rain and thunderstorms.
• When the washing machine is installed, the main socket must be within easy reach.
• Do not use extensions or multiple sockets.
• The power supply cable must never be bent or dangerously compressed.
• The power supply cable must only be replaced by an authorised serviceman.

Warning! The company denies all liability if and when these norms are not respected.

The first wash cycle
Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, setting the 90°C programme.

Technical data

Technical data

Model| IWC 71452
Dimensions| width 59.5 cm

height 85 cm

depth 53,5 cm

Capacity| from 1 to 7 kg
Electrical connections| please refer to the technical data plate fixed to the machine
Water connection| maximum pressure 1 MPa (10 bar) minimum pressure

0.05 MPa (0.5 bar) drum capacity 52 litres

Spin speed| up to 1400 rotations per minute
Test wash cycles in accordance with regulation 1061/2010

and 1015/2010

| Programme 5: Eco Cotton 60°.

Programme 5: Eco Cotton 40°.

This appliance conforms to the following EC Directives:

– 2004/108/EC dated 03/05/89 (Electromagnetic Compatibility)

– 2012/19/EU (WEB)

– 2006/95/EC (Low Voltage)

Care and maintenance

Cutting off the water and electricity supplies

• Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks.
• Unplug the washing machine when cleaning it and during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

• Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently.

Caring for the door and drum of your appliance

• Always leave the porthole door ajar in order to prevent unpleasant odours from forming.

Cleaning the pump
The washing machine is fitted with a self-cleaning pump which does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber which protects the pump, situated in its bottom part.

• Make sure the wash cycle has finished and unplug the appliance.

To access the pre-chamber

1. using a screwdriver, remove the cover panel on the lower front part of the washing machine (see figure)
2. unscrew the lid by rotating it anti-clockwise (see figure): a little water may trickle out. This is perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Checking the water inlet hose
Check the inlet hose at least once a year. If there are any cracks, they should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.

• Never use second-hand hoses.

Precautions and tips

This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully.

General safety

• This appliance was designed for domestic use only.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance. Clearing and user maintenance shall not be made by children without supervision.
• Do not touch the machine when barefoot or with wet or damp hands or feet.
• Do not pull on the power supply cable when unplugging the appliance from the electricity socket. Hold the plug and pull.
• Do not open the detergent dispenser drawer while the machine is in operation.
• Do not touch the drained water as it may reach extremely high temperatures.
• Never force the porthole door. This could damage the safety lock mechanism designed to prevent accidental opening.
• If the appliance breaks down, do not under any circumstances access the internal mechanisms in an attempt to repair it yourself.
• Always keep children well away from the appliance while it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy.
• Before loading laundry into the washing machine, make sure the drum is empty. the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected.
• Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliances.

Description of the washing machine and starting a wash cycle

Control panel

Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).
ON/OFF button: switches the washing machine on and off.
WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the available functions. The indicator light corresponding to the selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or excludes the spin cycle completely (see “Personalisation”).
WASH CYCLE PROGRESS/DELAY TIMER indicator lights: used to monitor the progress of the wash cycle. The illuminated indicator light shows which phase is in progress. If the Delay Timer function has been set, the time remaining until the wash cycle starts will be indicated (see next page).
DOOR LOCKED indicator light : indicates whether the door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the DOOR LOCKED indicator light is switched off, the door may be opened(wait approximately 3 minutes). To start the wash cycle from the point at which it was interrupted, press this button again.

Standby mode
This washing machine, in compliance with new energy-saving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. Press the ON-OFF button briefly and wait for the machine to start up again.

Indicator lights
The indicator lights provide important information.

This is what they can tell you
Delayed start
If the DELAY TIMER function has been activated (see “Personalisation”), after the wash cycle has been started the indicator light corresponding to the selected delay period will begin to flash:

As time passes, the remaining delay will be displayed and the corresponding indicator light will flash:

The set programme will start once the selected time delay has expired.

Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress.
Wash
Rinse
Spin
Drain

End of the wash cycle

• Function buttons and corresponding indicator lights When a function is selected, the corresponding indicator light will illuminate.
• If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and the function will not be activated.
• If the selected function is not compatible with another function which has been selected previously, the indicator light corresponding to the first function selected will flash and only the second function will be activated; the indicator light corresponding to the enabled option will remain lit.

Door locked indicator light
When the indicator light is on, the porthole door is locked to prevent it from being opened; make sure the indicator light is off before opening the door (wait approximately 3 minutes). To open the door during a running wash cycle, press the START/PAUSE button; the door may be opened once the DOOR LOCKED indicator light turns off.

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed manner, in green.
9. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
10. At the end of the wash cycle, the indicator light will switch on. The door can be opened once the DOOR LOCK indicator light turns off (wait approximately 3 minutes).
11. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washing machine off by pressing the ON/OFF button.

Wash cycles

Table of wash cycles

Wash cycles| ****

Description of the wash cycle

| ****

Max. temp. (°C)

| ****

Max. speed (rpm)

| Detergents| Max. load (kg)| Residual dampness %| Energy consumption kWh| Total water lt| Cycle duration
---|---|---|---|---|---|---|---|---|---
Wash| Fabric softener
Daily
1| White Cotton: extremely soiled whites.| 90°| 1400| l| l| 7| –| –| –| 160’
2| Mix Colored: lightly soiled whites and delicate colours.| 40°| 1400| l| l| 7| –| –| –| 90’
3| Synthetics: heavily soiled resistant colours.| 50°| 1000| l| l| 3,5| –| –| –| 110’
3| Synthetics (3): lightly soiled resistant colours.| 40°| 1000| l| l| 3,5| 44| 0,57| 53| 100’
4| Delicate| 30°| 0| l| l| 1| –| –| –| 80’
5| Eco Cotton 60° (1): heavily soiled whites and resistant colours.| 60°| 1400| l| l| 7| 53| 1,07| 52,5| 180’
5| Eco Cotton 40° (2): lightly soiled whites and delicate colours.| 40°| 1400| l| l| 7| 53| 1,00| 85| 170’
20° Zone
6| Cotton Standard 20°: lightly soiled whites and delicate colours.| 20°| 1400| l| l| 7| –| –| –| 170’
7| Mix Light| 20°| 1000| l| l| 7| –| –| –| 120’
8| 20’ Refresh| 20°| 800| l| l| 1,5| –| –| –| 20’
Special
9| Outwear| 30°| 400| l| –| 2| –| –| –| 60’
10| Wool: for wool, cashmere, etc.| 40°| 800| l| l| 1,5| –| –| –| 70’
11| Jeans| 40°| 800| l| l| 3,5| –| –| –| 75’
Sport 30°
12| Sport Intensive| 30°| 600| l| l| 2,5| –| –| –| 85’
13| Sport Light| 30°| 600| l| l| 2,5| –| –| –| 60’
14| Sport Shoes| 30°| 600| l| l| Max. 2 pairs| –| –| –| 60’
Partial
| Rinse| –| 1400| –| l| 7| –| –| –| 36’
| Spin + Drain| –| 1400| –| –| 7| –| –| –| 10’
*| Drain only | –| **| –| –| 7| –| –| –| 3’

If you select a program and exclude the spin cycle, the machine will drain only. The length of the cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1. Test wash cycle in compliance with regulation 1061/2010: set wash cycle 5 with a temperature of 60°C. This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2. Test wash cycle in compliance with regulation 1061/2010: set wash cycle 5 with a temperature of 40°C. This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes

1. Long wash cycle for cotton: set wash cycle 5 with a temperature of 40°C.
2. Long wash cycle for synthetics: set wash cycle 3; with a temperature of 40°C.

Personalisation

Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles). The temperature may be lowered, or even set to a cold wash. The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value set for each wash cycle.

Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle. The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

• Cotton 1400 rpm
• Synthetics 1000 rpm
• Wool 800 rpm

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol. The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.
   Note:

   • If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and the function will not be activated.
   • If the selected function is not compatible with another function which has been selected previously, the indicator light corresponding to the first function selected will flash and only the second function will be activated; the indicator light corresponding to the enabled option will remain lit.

Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled cotton and synthetic fabrics (refer to the “Table of wash cycles”). “ ” enables you to wash in less time thereby saving
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity. The function saves energy by not heating the water used to wash your laundry – an advantage both to the environment and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash results in the same average time as a standard cycle. For the best washing results, we recommend the usage of a liquid detergent.

Extra Rinse
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly useful for sensitive skin.

Delay Timer
This timer delays the start time of the wash cycle by up to 12 hours. Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button is pressed, the function will be disabled.
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching the set programme

Detergents and laundry

Detergent dispenser drawer
Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build-up on the inside of your appliance and contribute to environmental pollution.

• Do not use hand-washing detergents because these create too much foam.
• Use powder detergent for white cotton garments, for prewashing, and for washing at temperatures over 60°C.
• Follow the instructions given on the detergent packaging. Open the detergent dispenser drawer and pour in the detergent or washing additive, as follows.
• Do not pour detergent into the compartment 1.
• Detergent should only be poured into compartment Compartment Detergent for the wash cycle (powder or liquid)
• Liquid detergent should only be poured in immediately prior to the start of the wash cycle. compartment Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.
Preparing the laundry

• Divide the laundry according to
• the type of fabric/the symbol on the label
• the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the values listed in the “Table of wash cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

• 1 sheet 400-500 g
• 1 pillow case 150-200 g
• 1 tablecloth 400-500 g
• 1 bathrobe 900-1200 g
• 1 towel 150-250 g

Garments requiring special care

Delicate: use programme 4 to wash very delicate garments. It is advisable to turn the garments inside out before washing them. For best results, use liquid detergent on delicate garments. The 20° wash cycles (Zone 20°) offer effective washing performance at low temperatures, reducing electricity usage and expenditure while benefitting the environment.  The 20° wash cycles meet all requirements: Cotton Standard (programme 6) is ideal for heavily soiled cotton loads. The effective performance levels achieved at cold temperatures are comparable to washing at 40 ° and are guaranteed by a mechanical action which operates at varying speeds, with repeated and frequent peaks. Mix Light (programme 7) is ideal for mixed loads (cotton and synthetics) with a normal soil level.

The effective performance levels achieved at cold temperatures are guaranteed by a mechanical action which operates at varying speeds, across set average intervals. 20’ Refresh (programme 8) is ideal for refreshing and washing lightly soiled garments in a few minutes. It lasts just 20 minutes and therefore saves both time and energy. It can be used to wash different types of fabrics together (except for wool and silk), with a maximum load of 1.5 kg. Outwear (wash cycle 9): is studied for washing water-repellent fabrics and winter jackets (e.g. Gore-Tex, polyester, nylon); for best results, use a liquid detergent and dosage suitable for a half-load; pre-treat necks, cuffs and stains if necessary; do not use softeners or detergents containing softeners. Stuffed duvets cannot be washed with this programme.

Wool
all wool garments can be washed using programme 10, even those carrying the “hand-wash only” label. For best results, use special detergents and do not exceed 1,5 kg of laundry.

Jeans
Turn garments inside-out before washing and use a liquid detergent. Use programme 11. Sport Intensive (programma 12): is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we recommend not exceeding the maximum load indicated in the “Programme table”.

Sport Light (programma 13): is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we recommend not exceeding the maximum load indicated in the “Programme table”. We recommend using a liquid detergent and dosage suitable for a half-load. Sport Shoes (programma 14): is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and to distribute the load in a uniform manner, the drum rotates continuously at a speed which is slightly greater than the washing rotation speed. If, after several attempts, the load is
not balanced correctly, the machine spins at a reduced spin speed. If the load is excessively unbalanced, the washing machine performs the distribution process instead of spinning. To encourage improved load distribution and balance, we recommend small and large garments be mixed in the load.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be solved easily using the following list Remember, you will be charged for a service call for problems caused by incorrect installation, as indicated on pages 2 to 4. Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine. Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.

Product Guarantee and Repair Information

Guarantee

12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of the breakdown repairs for twelve months from the date of purchase. This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you:

• This guarantee is subject to the following conditions:
• The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions.
• The appliance is used only for electricity or gas supply printed on the rating plate.
• The appliance has been used for normal domestic purposes only.
• The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any person not authorised by us.
• Any repair work must be undertaken by us or our appointed agent.
• Any parts removed during repair work or any appliance that is replaced become our property.
• The appliance is used in the United Kingdom or Republic of Ireland. The guarantee does not cover:
• Damage resulting from transportation, improper use, neglect or interference or as a result of improper installation.
• Replacement of any consumable item or accessory.
• These include but are not limited to plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
• Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-DOMESTIC PREMISES.

Recycling and Disposal Information
As part of Indesit’s continued commitment to helping the environment, Indesit reserves the right to use quality, recycled components to keep down customer costs and minimise material wastage. Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug it, and cut the main cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket, and the door cannot be locked shut.

Repairs and After-sales

For product help and advice, repairs, spare parts or accessories, we’re here to help.
For local repair engineers – 03448 111 606
ROI – 0818 313 413
UK standard local rate applies
ROI local Irish rate applies

For Parts and Accessories visit parts.indesit.co.uk/shop Please remember to register your appliance at www.indesitservice.co.uk to activate your 10-year parts guarantee.
How to find your model and serial number: Indesit Company Spa
Viale Aristide Merloni, 47 60044 Fabriano (AN)
Italy www.indesit.com

Download PDF:Indesit IWC71452 Washing Machine Instruction Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>