TOSHIBA F-AXY60MY Ceiling Fan Instruction Manual

TOSHIBA F-AXY60MY Ceiling Fan

Product Information

CEILING FAN

• Model : F-AXY60MY(B)
• Weight : 6.5kg

Safety Precautions

• Make sure the ceiling hook can bear more than 80kg of the weight of the ceiling fan. If the ceiling fan falls, it may cause injury.

Installation Instructions

1. Ensure the distance between the fan blades and the ceiling does not exceed the 4mm difference for each blade.

Power Connection

• Power Input : 220-240V~

Product Specification

• Weight : 6.5kg

Installation Inspection
Please perform the following checks:

1. Check if the variance of distance between the fan blades and the ceiling does not exceed the 4mm difference for each blade.

Thank you very much for purchasing a Toshiba fan

• In order to use this fan correctly and safely, please read carefully this instruction manual and fully understand the content before using it.
• After reading the manual, keep it handy for easy reference.

SAFETY PRECAUTIONS

To avoid the possibility of injury to the user or damage to property, please follow all instructions described below.

WARNING:

CAUTION

PARTS FIGURE

WARNING: Do not replace with the modified pipe assembly, otherwise, it may cause the ceiling fan to fall and injured.

INSTALLATION INSTRUCTIONS

1. The rubber wheel of the pipe assembly CAUTION: Do not lose disassembled parts
2. Install the fan blades
   • Remove the pre-installed blade fixing screws on the motor bod
   • Place the blade paper pad between the motor and the blade
   • Fix the blade to the tightening torque baseline: 250-300N*cm
   • Fan blades must be properly tightened Otherwise, it may cause no airflow. If the fan blade falls. it mav cause injury.
3. Install the lower canopy
4. Pre-install the upper canopy
5. Install it on the hook
   • CAUTION : The split pin must be inserted into the bolt and then bent If the ceiling fan falls, it may cause injury.
6. Secure with the safety wire
7. Wire the ceiling fan body
   • Fix the ground wire of the ceiling fan and the external ground together on the pipe assembly with screws
   • Pull the power (live and null) line of the ceiling fan over and tie on the pipe assembly
   • Connect the live and null line of the ceiling fan respectively to the external live and null line
   • Note : The ceiling fan is not provided with wiring terminals.

POWER CONNECTION

This product is not provided with cables and plugs or other accessories used to connect to the power supply. When connecting or replacing cables or wires, the work must be carried out by talito othere times such as Preter t. rese omply witutevant national regulations).

Fix the upper canopy

Install the speed controller

Disassemble the speed controller

Wire the speed controller

1. Install the wall socket into the wall hole (Not provided by the manufacturer)
2. The wood thread screw (Wall socket is not provided by the manufacturer) is used for the speed controller fixing bracket
3. The live line of the ceiling fan is fixed after it is pulled through from the bottom and inserted into the terminals, and the live line of the power supply is fixed after it is pulled through from the bottom and inserted into the terminals.
4. The base is placed on the speed controller bracket for pre-installation.
5. The shell is placed on the base for pre-installation.
6. The shell and the base are for screw fixing.

Measure the distance with a tane

Please adjust all fan blades so that the distance from the ceiling to the end L of the fan blades is equal (with a tolerance of 4 mm). If the distance difference between the blades is greater than 4mm, the blades need to be adjusted.

Adjustment method of fan blade:

1. Remove the fan blade with the largest distance from the ceiling, add a gasket between the fan blade and the motor, and then lock the fan blade with screws.
2. Retest the distance between the fan blade and the ceiling. If the distance difference is less than 4mm, it meets the requirements. If the distance difference is greater than 4mm, add a second basket between the fan blade and the motor.
3. Then test the distance between the fan blade and the ceiling. If the distance difference is less than 4mm, it meets the requirements. If the distance difference is more than 4mm, it might cause wobbling.

The installation personnel shall use a tapeline or ruler to measure and manage

1. Place one end of the tapeline or ruler on the ceiling
2. Measure the dimension and distance readings at the tail end of each blade vertically
3. Note : When measuring, the tapeline or ruler shall be in the same position.
4. Regular measurement and correction shall be carried out every six months.

CAUTION: After installation, please make sure that the ceiling fan does not wobble extremely. If the ceiling fan falls, it may cause injury.

PRODUCT SPECIFICATION

INSTALLATION INSPECTION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>