IDEAL HK01-I GL Lever Set with Keyed Deadbolt Instructions
- June 13, 2024
- IDEAL
Table of Contents
IDEAL HK01-I GL Lever Set with Keyed Deadbolt Instructions
WARNING: VERIFY DOOR PROFILE PRIOR TO INSTALLATION
You will require a profile wide enough for proper installation. With the door closed, the minimum inside door profile width is 1-7/8″ from the edge of the door frame (glass side) to the edge of the door jamb or metal door frame (z-bar), which ever is narrower. The minimum outside door profile width is 2″ from the edge of the door frame (glass side) to the edge of the door jamb or metal door frame (z-bar), which ever is narrower.
Drilling template prerequisite: Determine if your storm door is right or
left-handed.
From outside of the door, looking in, if the hinges are on your left, your
door is left handed. Your door will open to the left side. If the hinges are
on your right, your door is right handed. Your door will open to the right
side. Ensure that the inside latch paddle does not interfere with the prime
door lock.
TEMPLATE PLACEMENT AND DRILLING INSTRUCTIONS
- Fold the template on the dotted line to 90 degrees according to the handedness (left or right).
- With the door in closed position, place folded template on the inside of the door so that the SIDE A is against the jamb or metal z-bar, which ever projects out furthest; and SIDE B is on the inside surface of the door.
- Use a center punch to mark the position of 6 holes on the inside surface of the door on SIDE B. Mark the position of 4 holes on the jamb on SIDE A (for strikes).
- Using a 5/16″ drill bit, drill 6 holes straight through door on SIDE B.
- Using a 1/16″ drill bit, drill 4 pilot holes to a depth of 1″ on the jamb on SIDE A
DRILLING TEMPLATE
Print out this sheet at 1:1 scale
SPINDLE SELECTION FOR HANDLE
- Measure the thickness of your door.
- Print out this sheet using 1:1 scale.
- Overlay spindle on top of the image.
- Select the spindle that matches your door thickness.
SCREW SELECTION FOR DEADBOLT
- Print out this sheet using 1:1 scale.
- Overlay screws on top of the image.
- Select the screws that match your door thickness
Door Thickness
SCREW SELECTION FOR LATCH
- Measure the thickness of your door.
- Print out this sheet using 1:1 scale.
- Overlay screws on top of the image.
- Select the screws that match your door thickness.
Door Thickness
SPINDLE PREPARATION FOR KEY LOCK
- Print this sheet using 1:1 scale.
- Overlay flat spindle against the image.
- Mark door thickness on the spindle.
- Cut off the portion of the spindle beyond the mark line.
Ruler for Door Thickness
HANDLE & LATCH INSTALLATION
- Rotate the outside handle to the left or right according to your door handedness.
- Insert the pre-selected handle spindle (see page 4) into the center hole of the outside handle from the back side of the handle housing; ensure the spindle is fully fitted into the hole. The spindle locks the handle in place.
- Place the outside handle assembly on the door. If your door thickness is not standard, then the spindle should project through inside of the door a max of 3/8″ and a min of 1/4″. You may have to shorten the spindle.
- Place the latch on the inside of the door, fasten with two machine screws pre-selected (see page 4). Do not over tighten screws.
- Place the latch strike and the thick spacer against the jamb. The spacer shall be placed in between the strike and the jamb. Align with pilot holes on jamb and fasten with two tapping screws.
KEY LOCK & DEADBOLT INSTALLATION
- Place the key lock on the outside of the door and hold it in place temporally by hand.
- Insert the pre-prepared flat spindle (see page 4) from the inside through the center hole into the keylock; ensure the spindle is fully inserted. If your door thickness is not standard, then the spindle should project through inside of door a max of 1/2″ and min of 1/4″. Cut off the excessed portion of the spindle.
- Place the deadbolt on inside of the door, align the center hole carefully with the spindle, fasten with two pre-selected machine screws (see page 4). Do not over tighten screws.
- Place the strike for the deadbolt on jamb, align with pilot holes on jamb, fasten with two tapping screws.
CUSTOMER SERVICE
Thank you for your purchase. We are dedicated to customer service and will work to resolve any difficulties to ensure customer satisfaction. If you have any questions about the setup or function of this product, please contact us.
Scan for more information
Tel.: 1-800-361-2236
Email/Courriel: info@idealinc.com
Support/Soutient: www.idealinc.com/help
FAQ: help.idealinc.com
https://www.idealinc.com/
https://www.facebook.com/IdealSince1956
https://www.youtube.com/user/IdealSecurityInc
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>