GIBSON 619718B Stainless Axle Back Quad Tip Rear Exhaust System Instruction Manual
- June 13, 2024
- Gibson
Table of Contents
GIBSON 619718B Stainless Axle Back Quad Tip Rear Exhaust System
Product Information
- Product Name: Stainless Axle Back Quad Tip Rear Exhaust System
- Compatible Vehicle : 2020-2023 Ford Explorer ST 3.0L Eco-Boost (Factory Quad Tip Exhaust)
Part Number: 619718B
| ITEM | PART | QUANTITY | DESCRIPTION |
|---|---|---|---|
| A | 999701122S | 1 | 2.25 SS Passenger Muffler Assembly |
| B | 999701123S | 1 | 2.25 SS Driver Muffler Assembly |
| C | 5756 | 2 | 2.25 Clamp |
| D | 500433-B | 4 | Rolled Round Tip |
If you need further assistance, please contact our technical department at 800-528-3044 from Monday to Friday, 8am to 5pm.
Product Usage Instructions
Important Safety Precautions:
- Use jack stands when working under the vehicle.
- Set the parking brake and block the tires.
- Wear safety glasses and gloves.
- Allow the exhaust to cool before installation to prevent burns or injuries.
Suggested Tools:
- 9/16 wrenches & sockets
- WD-40
- Hacksaw
- Disconnect the negative battery cable before removing the OEM exhaust. This will allow the computer to reset and recognize the new exhaust.
- Lay out the exhaust system on the floor and compare the parts with the manual.
- Cut both tailpipes 1.5 inches from the beginning of each straight section closest to the muffler. Refer to the provided photo for the marked cutting points. Make sure to cut correctly.
- Remove both muffler assemblies and clean the burrs on both pipes that are still attached to the vehicle.
- Install the driver side muffler assembly (Part A) onto the factory pipe using clamp C.
- Install the passenger side muffler assembly (Part B) using another clamp C.
- Install all tips (Part D) onto the exhaust exits and tighten the exhaust system.
Note:
GIBSON EXHAUST systems are designed for factory stock vehicles. Installing
aftermarket products may increase the sound levels of the exhaust. Ensure a
1-inch clearance from all rubber brake lines, shock boots, lines, tires, etc.
to prevent heat-related damage or fire.
| ITEM | PART | QUANTITY | DESCRIPTION |
|---|---|---|---|
| A | 999701122S | 1 | 2.25” SS Passenger Muffler Assembly |
| B | 999701123S | 1 | 2.25” SS Driver Muffler Assembly |
| C | 5756 | 2 | 2.25” Clamp |
| D | 500433-B | 4 | Rolled Round Tip |
Installation Instructions #619718B
When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
SUGGESTED TOOLS: 9/16″, wrenches & sockets, WD-40, hacksaw
- Disconnect the negative battery cable before removal of OEM exhaust. This will allow the computer to reset and recognize the new exhaust. Lay out the exhaust on the floor so it looks like the drawing and compare parts with manual.
- First you’ll need to cut both tailpipes 1.5″ from the beginning of each straight closest to the muffler, the cuts are marked in this photo. (BE SURE YOU CUT CORRECTLY). Once cut you may remove both muffler assembly’s and clean the burr on both pipes that are still on the vehicle.
- Next, you may install driver side muffler assy. #A onto the factory pipe using clamp #C.
- Now begin installing the passenger side muffler assy. #B using another clamp #C. Once finished you may install all tips #D onto the exits and tighten the exhaust.
GIBSON EXHAUST systems are designed on a factory stock vehicle. Any aftermarket products installed could increase the sound levels of the exhaust. Make sure there is a 1” clearance from ALL rubber brake lines, shock boots, lines, tires, etc. to prevent heat related damage or fire.
- Thank you for purchasing our Gibson Exhaust System for your vehicle.
- If you need further assistance, please do not hesitate to call our technical department at (800) 528 -3044 Monday through Friday, 8am to 5 pm.