Gerni Super 130.2 S Pressure Washer User Guide

: June 13, 2024
: Gerni

Table of Contents

Super 130.2 S Pressure Washer
Product Information
Safety Precautions and Warnings

Super 130.2 S Pressure Washer

Product Information

The product is a high-pressure washer manufactured by Gerni. The
model variants available are Super 130.2 S, Super 130.2, Super
135.2, Super 140.2, and Super 145.2. The user manual for the
product can be found at https://manual-hub.com/. The manual
provides important safety precautions, warnings, and instructions
for using the high-pressure washer.

Safety Precautions and Warnings

Safety instructions marked with the symbol !
must be observed to prevent danger to persons.
The symbol ! is used to mark safety
instructions that must be observed to prevent damage to the machine
and its performance.
The symbol ***** indicates tips and instructions
to simplify work and ensure safe operation.
Inhalation of aerosols can be hazardous to health. Use a
device, such as a shield covering the nozzle, to avoid or reduce
aerosol production. For protection against aerosols, use a
respiratory mask of class FFP 2 or higher.
The appliance is not intended for use by persons (including
children) with reduced physical, sensory, or mental capabilities,
unless they have been given supervision or instruction concerning
its use by a person responsible for their safety.
High-pressure cleaners should not be used by children or
untrained personnel.
Children should be supervised to ensure they do not play with
the appliance.
When transporting, operating, servicing, and storing the
machine, ensure it is in an upright position and placed on a plain
surface.
Before starting the machine, carefully check for any defects.
If any defects are found, do not start the machine and contact your
Gerni distributor.
High-pressure jets can be dangerous. Never direct the water jet
at persons, pets, live electrical equipment, or the machine itself.
Do not attempt to clean clothes or footwear on yourself or others.
Hold the spray lance firmly with both hands during operation.
Use adequate extension cables suitable for outdoor use. Keep
the connection dry and off the ground. It is recommended to use a
cable reel to keep the socket at least 60 mm above the ground.
Extension cables must comply with specified length and cable
dimensions.
If the electric cable is damaged, it must be replaced by the
manufacturer, their service agent, or a similarly qualified person
to avoid hazards.

Product Usage Instructions

Before starting up the high-pressure washer for the first time,
carefully read through the instruction manual and save it for later
use.
Ensure that the appliance is placed on a plain surface in an
upright position before transporting, operating, servicing, or
storing it.
Inspect the machine for any defects before starting it. If any
defects are found, do not start the machine and contact your Gerni
distributor.
When using the high-pressure washer, never direct the water jet
at persons, pets, live electrical equipment, or the machine itself.
Avoid cleaning clothes or footwear on yourself or others.
Hold the spray lance firmly with both hands during
operation.
Use appropriate protective measures, like a shield covering the
nozzle, to avoid or reduce aerosol production. For protection
against aerosols, use a respiratory mask of class FFP 2 or
higher.
Supervise children to ensure they do not play with the
appliance.
Use suitable extension cables that are designed for outdoor use
and keep the connection dry and off the ground. It is recommended
to use a cable reel to elevate the socket at least 60 mm above the
ground.
Comply with the specified length and cable dimensions for
extension cables.
If the electric cable is damaged, it must be replaced by the
manufacturer, their service agent, or a similarly qualified
person.
Follow the manufacturer’s instructions for mains power
connection when connecting the high-pressure washer to the electric
installation.

Why compromise

Super 130.2 S Super 130.2 Super 135.2 Super 140.2 Super 145.2
User Guide

Super 130.2 S Super 130.2 Super 135.2 Super 140.2 Super 145.2

128303529 c (11.2013)

Index
1 Safety precautions and warnings ………………………………………3 2 Description …………………………………………………………………….4 3 Before you start using your pressure washer ………………………5 4 Operating your pressure washer ……………………………………….6 5 Fields of application and working methods ……………………….10 6 After using your pressure washer…………………………………….12 7 Maintenance…………………………………………………………………13 8 Trouble shooting ……………………………………………………………14 9 Further information………………………………………………………..15 10 Technical Data………………………………………………………………18 11 Declaration of Conformity……………………………………………….19

1 Safety Precautions and Warnings

Symbols used to mark instructions

Before starting up your high-pressure washer for the first time, this instruction manual must be read through carefully. Save the instructions for later use.

persons.

Safety instructions marked with this symbol must be observed to prevent danger to

This symbol is used to mark safety instructions that must be observed to prevent damage to the machine and its performance.
This symbol indicates tips and instructions to simplify work and to ensure safe operation.

WARNING! Inhalation of aerosols can be hazardous to health. Where applicable use a device in order to avoid or reduce aerosols production, e.g., a shield covering the nozzle. For protection against aerosols use a respiratory mask of class FFP 2 or higher.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

High pressure cleaners shall not be used by children or untrained personnel.
Children should be supervised to ensure that they do not play with the appliance.
When transporting, operating, servicing and storing the machine always make sure that it is in upright position and placed on a plain surface.
Before starting up your machine please check it carefully for any defects. If you find any, do not start up your machine and contact your Gerni distributor.

Especially check: The insulation of the electric
cable should be faultless and without any cracks. If the electric cable is damaged, an authorized Gerni distributor should replace it.
WARNING! High pressure jets can be
dangerous. Never direct the water jet at persons, pets, live electrical equipment or the machine itself. Never try to clean clothes or footwear on yourself or other persons. Hold the spray lance firmly with both hands. The spray lance is affected by a thrust of up to 16.4 N during ope-

Original instructions

3

ration. The operator and anyone in
the immediate vicinity of the site of cleaning should take action to protect themselves from being struck by debris dislodged during operation. Wear goggles and protective clothes during operation. This appliance has been designed for use with cleaning agents supplied or recommended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the appliance. To ensure the appliance safety only use original spare parts from the manufacturer or approved by the manufacturer. High pressure hoses, fittings and couplings are important for the safety of the appliance. Only use hoses, fittings and couplings recommended by the manufacturer. Do not use the appliance if a supply cord or important parts of appliance are damaged, e.g. safety device, high pressure hose and trigger gun. Remove the plug from the socket outlet during cleaning or maintenance and when replacing parts or converting the machine to another function. The appliance is intended for cleaning outdoors. Appropriate ear protection must be used. Do not cover the machine during operation. Never use the machine in an environment where there could be a danger of explosion. If any doubt arises, please contact the local authorities. It is not allowed to clean asbestos- containing surfaces with high pressure. WARNING! Risk of explosion -Do not spray flammable liquids. Always swith off the mains disconnecting switch when

leaving the machine unattended. This high pressure washer must not be used at temperatures below 0°C. Never let any persons stand under the product when stored on the wall.

WARNING! Inadequate extension cables can be dangerous. If an extension cable is used, it shall be suitable for outdoor use, and the connection has to be kept dry and off the ground. It is recommended that this is accomplished by means of a cable reel which keeps the socket at least 60 mm above the ground. Cables on extension lead drums should always be completely unwound to prevent the cable from overheating.

Extension cables must comply with the below-mentioned requirements for length and cable dimensions.

1.0 mm² max. 1.5 mm² max. 2.5 mm² max.

12.5 m 20 m 30 m

If the electric cable is damaged, it must be replaced by the manufacturer or his service agent or similarly qualified person in order to avoid a hazard.

Mains power connection

The following should be observed when connecting the high pressure washer to the electric installation:
The electric installation shall be made by a certified electrician and comply with IEC 364.
It is recommended that the electric supply to this appliance should include either a residual current device that will interrupt the supply if the leakage current to earth ex-

ceeds 30 mA for 30 ms.
Water connection Connection to the public mains according to regulations.
Inlet hose can be connected to the water mains with a max. inlet pressure of 10 bar.
IMPORTANT! Only use water without any impurities. If there is a risk of silt, sand or sediment in the inlet water (i.e. from your own well), an additional filter should be mounted.
Safety devices Locking device on spray gun (7a) (see illustration at the end of this manual): The spray gun features a locking device. When the button is activated, the spray gun cannot be operated.
Thermal sensor: A thermal sensor protects the motor against overloading. The machine will restart after a few minutes when the thermal sensor has cooled.
Pressure safety device An integrated hydraulic safety valve protects the system from excessive pressure.

4

Original instructions

2 Description

2.1 Application
2.2 Operation elements and model survey

This high-pressure washer has been developed for domestic use for cleaning:
– Car, motorbike, boat, caravan, trailer, patio/drive/flagstones, woodwork, brickwork, barbecue, garden furniture, lawn mower
Section 5 describes the use of

the high-pressure washer for vaious cleaning jobs.
Only use the high-pressure washer for purposes described in this manual.
The safety precautions must be observed to prevent damage to the machine, the surface to be cleaned or severe personal injuries.

See illustration at the end of this manual.
1 Start/stop switch 2 Water inlet (with filter) 3 High pressure connection
(only models without hose reel) 4 High pressure hose 5 Electric cable 6 Click & Clean spray lance 7 Spray gun with lock 8 Click & Clean Tornado® PR nozzle 9 Click & Clean Powerspeed® nozzle 10 Click & Clean foam sprayer

11 Nozzle cleaning tool 12 Trolley handle (tele-scopic
handle), except 130.2 S 13 Hose reel (not standard) 14 Hose hook 15 Model tag 16 Quick coupling 17 Button for telescopic
handle, except 130.2 S 18 Turnable cable hook
Specifications: See model tag (15) of machine.
We reserve the right to alter the specifications.

3 Before you start using your pressure washer

3.1 Mounting of trolley handle and hose hook
3.1.1 Super 130.2, 135.2, 140.2, 140.2 Plus
Original instructions

1. Push down the trolley handle (12) over the two metal tubes. Make sure that the handle is mounted as illustrated. Mount screws with nuts (make sure that the screws go through handle as well as tube).
2. Mount the hose hook (14) on the machine (2 screws). Note: the hose hook can be mounted on the front as well as on the back. Front position is to be used if the product is
5

3.1.2 Super 130.2 S
3.2 Mounting of hose reel handle (models with hose reel)

used together with a special wall hook for wall storage (not standard 130.2 models).
1. Mount the trolley handle (12) on the machine. Secure the handle by tightening the 4 screws.
2. Mount the hose hook (14) on the machine (2 screws). Note: the hose hook can be mounted on the front as well as on the back. Front position is to be used if the product is used together with a special wall hook for wall storage (not standard).
1. Click the hose reel handle on to the trolley handle (no screws).

3.3 Mounting of quick coupling

1. Screw the quick coupling (16) tight on to the water inlet (2).
Note: The inlet filter must always be fitted in the water inlet pipe to filter out sand, limestone and other impurities as these will damage the pump valves.
Caution: Failure to fit the filter will invalidate the guarantee.

6

Original instructions

3.4 Mounting of high pressure hose

Attach the high pressure hose (4) to the spray gun (7).
Detach the high pressure hose by pressing the button (A).

4 Operating your pressure washer

4.1 Connection of high pressure hose (models without hose reel)

1. Mount the high pressure hose on the outlet (3).

4.2 Mounting of spray lance and Click & Clean nozzles

1. Push the spray lance (6) into the spray gun (7) and twist it until the bayonet coupling locks into position..

Note: The spray lance (6) has a built-in low pressure nozzle that can be used for flushing away dirt. 2. Attach the nozzle.
Warning: When attaching the Click & Clean nozzles, the button on the side of the spray lance should return to the locked position. Ensure that there is an audible “click”.

Note: The Tornado® PR nozzle and the foam sprayer feature a swivel lock, which must be positioned in the hole in the Click & Clean spray lance.

Original instructions

7

4.3 Water connection
4.4 Telescopic handle (Super 130.2, 135.2, 140.2, 140.2 Plus)

Press the button to detach the Click & Clean nozzle.

An ordinary 1/2″ garden hose of min. 10 m and max. 25 m will be suitable.

sediment in the inlet water (i.e. from your own well), an additional filter should be mounted.

NOTE: Connection to the public mains according to regulations.
IMPORTANT! Only use water without any impurities. If there is a risk of silt, sand or

1. Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrating the machine. Note: Check that the filter is fitted in the water inlet pipe and that it is clean and free from debris (it is factory fitted).
2. Connect the water hose to the water supply by means of the quick connector (inlet water, max. pressure: 10 bar, max. temperature: 50°C).
3. Turn on the water.

The machine (Super 130.2, 135.2, 140.2, 140.2 Plus) features a telescopic handle. To raise or lower the handle, press the knob and move the handle upwards or downwards. When a click is heard, the handle is in right position.

8

Original instructions

4.5 Start and stop of the machine (when connected to a water supply)

The spray lance is affected by a thrust during operation – therefore always hold it firmly with both hands. IMPORTANT: Point the nozzle at the ground.
1. Check that the machine is in upright position. NOTE: Do not place the machine in tall grass!
2. Release the trigger lock. 3. Activate the trigger of the
spray gun and let the water run until all air has escaped from the water hose. 4. Turn the start/stop switch (1) to position “I”. 5. Activate the trigger of the spray gun.
Always adjust the distance and thus the pressure of the nozzle to the surface, which is to be cleaned.

Do not cover the machine during operation.
Note: If the machine is left or not used for 5 minutes, it must be switched off on the start/stop switch “O” (1):
1. Turn the start/stop switch to position “O”.
2. Disconnect the electrical plug from the socket.
3. Shut off the water supply and activate the trigger to relieve the machine of pressure.
4. Lock the spray gun.
When releasing the trigger of the spray gun, the machine automatically stops. The machine will start again when you re-activate the spray gun.

4.6 Start the machine (when connected to open containers (suction mode))

The washer can draw water from a rain water tank or bucket as an example. The hose for the water supply must not be too long, approx. 5 m.
Make sure that the water tank is not placed on a lower level than the machine.
Use an external filter if the water contains impurities.
1. Make sure that the water hose is filled completely with water before connecting to the machine. Place the entire hose in a tank or bucket. To avoid water spillage, crimp the water inlet hose down in

the water and then connect the hose to the machine with the quick coupling and finally uncrimp the water inlet hose. 2. Turn the start/stop switch to position “I”. 3. Activate the trigger of the spray gun with lance and nozzle removed and let the water run, until the air has escaped from the water hose and the pump. 4. Mount spray lance and nozzle.

Original instructions

9

4.7 Pressure regulation on the TORNADO® PR-nozzle

High pressure Højtryk

The pressure can be regulated on the TORNADO® PR nozzle.

4.8 Stationary use

A

C

B

Low preLasvsturyrke

D

If mounting a special wall hook (not standard), the pressure washer can be used as a stationary solution meaning that it can be operated while hanging on the wall.
Only mount the wall hook on a sturdy wall. Adjust the length of the screws and size of rawlplugs to the type of wall.
On the wall hook garden/rim brush (a) foam sprayer (b), Click & Clean brush (c) and Click & Clean nozzles (d) can be stored.
Important: The bearing capa-
city of the wall hook is max. 30 kg.

10

Original instructions

5 Fields of application and working methods

5.1 General

Efficient high presure cleaning is achieved by following a few guidelines, combined with your own personal experience of specific cleaning tasks. Accessories and detergents, when correctly chosen, can increase the efficiency of your pressure washer. Here is some basic information about cleaning.

5.1.1 Detergent and foam

Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt. Detergents are applied from bottom to top, for example on a car bodywork, in order to avoid “super clean” areas, where the detergent collects in higher concentration and streams downwards. Let the detergent work for several minutes before rinsing but never let it dry on the surface being cleaned. Note: It is important that the detergents do not dry up. Otherwise the surface that has to be cleaned can be damaged.

5.1.2 Mechanical effect

In order to break down tough layers of dirt, additional mechanical effect may be required. Special wash brushes offer this supplementary effect that cuts through dirt (especially by car washing).

Original instructions

11

5.2 Typical fields of application

Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer from Gerni in association with accessories and detergents.

Task

Accessories `Click Cleaning method & Clean’

Car

Car nozzle,

1. Apply neutral car wash with the foam sprayer. Always start

auto brush,

from the bottom and work upwards. Let neutral car wash act

underchassis

for at least 5 min.

nozzle,

2. Wash the car with the car nozzle, which has been optimized for

Foam sprayer,

quick and gentle cleaning of enamelled surfaces (the jet is wider

Neutral car wash

and not so sharp). Start at the front of the car and work back-

wards to avoid water from penetrating via the door seals.

3. Use the brush for removal of traffic film which is not removed by the

nozzle. If the car is very dirty, apply neutral car wash again.

4. Attach the undercarriage nozzle and clean undercarriage and

wheel arches.

5. Remove water from the surface of the car with the squeegee

on the car brush. Make sure that all grains of sand etc. have

been removed before using the squeegee. Wipe with a wash

leather where the squeegee cannot reach.

Rims, aluminium

Rim brush, auto nozzle, atomizer, alloy cleaning agent

Apply alloy cleaning agent with an automizer. Let it act for approx. 5 min. and wash with the rim brush. For steel rims, use neutral car wash. Use the foam sprayer and wash with rim brush. Be careful! The high pressure jet may damage the tyres.

Flagstones, concrete floors and other hard surfaces

Powerspeed® nozzle, neutral detergent, Patio Cleaner

Wash towards outlets or the like. On surfaces with fouling you may start by applying Neutral detergent with the foam sprayer. Wash before the soap dries. Another more effective and quicker method is to use the Patio Cleaner. Thus you will also avoid splashes.

Garden Wood Cleaner furniture, Garden brush wood

Apply Wood Cleaner and wash before the soap dries. NOTE: Use the garden brush to clean off the dirt.

Brickwork, Wood work

Powerspeed® nozzle, neutral detergent, Patio Cleaner

Same method as for flagstones, but be careful – bad joints and wood may be damaged by high pressure. You may choose only to use the Tornado® nozzle. Adjust the distance (pressure) to the quality of the joints and the wood. Patio Cleaner can also be used on vertical surfaces.

Gutter

Underchassis spray Wash the gutter with the nozzle. Always wash towards

lance

downpipes. Beware not to spray under the roofing.

Cleaning Tube cleaner of drain pipes, outlets, down pipes etc.

Push the tube cleaner approx. ½ m (to mark) into a tube or drain and activate the trigger of the spray handle. The nozzle opening turning backwards will pull the cleaner through the tube. The nozzle will break down the ,,plug” and flush the dirt backwards.

Rust, paint Water/sandblasting Mount the water/sand blasting equipment and rust and paint

equipment

is efficiently and quickly removed. Beware not to damage the

surface to be sandblasted.

Greenhouse

Tornado® PR nozzle Wash with high pressure and maybe a brush. You may use neubrush, neutral de- tral detergent to remove fouling. tergent

Garden tools, lawn mower

Tornado® PR nozzle, Powerspeed® nozzle, multiangle adaptor, degreaser

Rinse the worst dirt off with the nozzle. Apply degreaser with the foam sprayer and let it act for approx. 5 min. Wash with the nozzle. You may use the multiangle adaptor for hard to get at areas to avoid splashing.

12

Original instructions

6 After using your pressure washer

6.1 Storing the washer

The machine should be stored in a frost-free room!
Pump, hose and accessories should always be emptied of water prior to storing as follows:
1. Stop the machine (turn the start/stop switch (1) to position “O” and detach water hose and accessory.
2. Restart the machine and activate the trigger. Let the machine run until no more water runs through the spray gun.

3. Stop the machine, unplug and wind up hose and cable.
4. Place spray handle, nozzles and other accessories in the holders of the machine.
Should the machine by mistake be frozen, it will be necessary to check it for damage.
NEVER START-UP A FROZEN MACHINE.
Frost damages are not covered by the guarantee!

6.2 Winding up of electric cable and high pressure hose

To avoid accidents, the electric cable and the high pressure hose should always be wound

up carefully.
1. Wind up the electric cable on the appropriate hooks. A built in clip secures the cable (1). The lower hook can be turned to release the electric cable.
2. The high pressure washer comes in two models: A) with hook for storage of high pressure hose (14) – B) with a hose reel (13).

6.3 Storage of accessories
e
d a + f
b c

f The standard accessories (spray gun (f), spray lance (a),
d nozzles (b) foam sprayer (c)) can be stored on the pressure
b washer.
e The nozzle cleaning tool (d)
c and a Click & Clean brush (e) can also be stored on the product.

Original instructions

13

7 Maintenance

WARNING! Always disconnect the electrical plug from the socket prior to maintenance or cleaning. To ensure a long and problem free working life, please take the following advice:
Wash off water hose, high pressure hose, spray lance and accessories before mounting.
Clean the connectors of dust

and sand. Make sure that no sand or dirt is blocking the movement of the button on the Click & Clean spray lance. Rinse the detergent spraying attachment after use. Clean the nozzles.
Any repair should always be made in an authorized workshop with original spare parts.

7.1 Cleaning of water inlet filter

Clean the water inlet filter regularly once a month or more frequently according to use. Carefully loosen the filter with a pair of pliers and clean it. Check that it is intact before re-mounting it.
The inlet filter must always be fitted inside the water inlet pipe to filter out sand, limestone and other impurities, as they will damage the pump valves.
CAUTION: Failure to fit the filter will invalidate the guarantee.

7.2 Cleaning of nozzle

A clogging up in the nozzle causes a pump pressure which is too high. This is why cleaning is required immediately.
1. Stop the machine and disconnect the nozzle.
2. Clean the nozzle. IMPORTANT: The cleaning tool (11) should only be used when the nozzle is detached!
3. Flush the nozzle backwards with water.

7.3 Cleaning of machine vents
14

The machine should be kept clean so as to let cooling air pass freely through the machine vents.

Original instructions

7.4 Greasing of couplings

To ensure easy connection and that o-rings do not dry up, the couplings should be greased regularly.

8 Trouble Shooting

Please ensure that you check the following before contacting the Gerni service organization:

Symptom Machine refuses to start Fluctuating pressure Motor hums Machine stops
Fuse blows Machine pulsating
Machine often starts and stops by itself Machine starts, but no water comes out

Cause Machine not plugged in Defective socket Fuse has blown Defective extension cable Pump sucking air
Low voltage or low temperature Fuse has blown Incorrect mains voltage
Thermal sensor activated
Nozzle partially blocked Fuse too small
Air in inlet hose/pump
Inadequate supply of mains water
Nozzle partially blocked Water filter blocked Hose kinked Pump/spray gun is leaking Pump/hoses or accessory frozen No water supply Water filter blocked Nozzle blocked

Recommended action
Plug in machine. Try another socket. Replace fuse. Switch off other machines. Try without the extension cable.
Check that hoses and connections are airtight.
Activate the trigger of the spray gun.
Replace fuse. Switch off other machines. Check that the mains voltage corresponds to specification on the model tag. Leave the washer for 5 minutes to cool down. Clean the nozzle (see section 7.2)
Change to an installation higher than the amp. consumption of the machine. You may try without the extension cable.
Allow machine to run with open trigger until regular working pressure resumes. Check that the water supply corresponds to specifications required (see model tag) NB! Avoid using long, thin hoses (min. 1/2″) Clean the nozzle (see section 7.2) Clean the filter (see section 7.1) Straighten out hose.
Contact your nearest Gerni Service Centre.
Wait for pump/hoses or accessory to thaw.
Connect inlet water. Clean the filter (see section 7.1) Clean the nozzle (see section 7.2)

In case problems other than the above occur, please phone 1300 733 171 or check our website www.gerni.com.au for your nearest service agent.

Original instructions

15

9 Further information

9.1 Recycling the washer

Make the old cleaner unusable immediately.
1. Unplug the cleaner and cut the electric cable.

tive 2002/96/EC on old electrical and electronic appliances, used electrical goods must be collected separately and recycled ecologically.

Do not discard electrical appliances with household waste.
As specified in European Direc-

Contact your local authorities or your nearest dealer for further information.

9.2 Warranty conditions 16

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Gerni high-pressure washers for domestic use are warranted for 2 years (complete machine) and the motor pump unit is warranted for a total of 5 years from the date of purchase by:
AUSTRALIA: Nilfisk-Advance Pty LTd Unit 1/13 Bessemer Street Blacktown NSW 2148 Phone: 1300 556 710 E-mail: sales@gerni.com.au
NEW ZEALAND: Accent Tools Ltd 232 Bush Rd Albany Auckland 0632 Phone: 09 968 2610 E-mail: sales@accent-tools.co.nz
Equipment defects covered by this warranty will be repaired or replaced by one of the service

centres of the Gerni organisation. Find your local service agent here: http://www.gerni.com.au/.
If your high pressure washer or accessories are handed in for repair, it must be followed by a description/specification of the fault, and the original purchase receipt, or a copy, must be enclosed.
Packing and postage/carriage is not covered by the warranty.
The benefits under this warranty are in addition to your national law of sale.
Guarantee repairs are made on the following conditions:
that defects are attributable to flaws or defects in materials or workmanship. (wear and tear as well as misuse are not covered by the guarantee).
that the directions of this instruction manual have been thoroughly observed.
that repair has not been carried out or attempted by other than Gerni-trained service staff.
that only original accessories have been applied.
that the product has not been exposed to abuse such as knocks, bumps or frost.

Original instructions

that only water without any impurities has been used.
that the high pressure washer has not been used for rental nor used commercially in any other way.
Repairs not covered by the guarantee conditions will be invoiced. (i.e. malfunctions due to Causes mentioned in section Trouble Shooting of the

instruction manual).
Please phone 1300 733 171 (Australia) or 09 9682610 (NZ) for service or warranty assistance only after checking possible causes in the trouble shooting chart on page 15.

9.3 Accessories
Only use original accessories.
Click & Clean Car nozzle
Click & Clean Undershassis nozzle

Special nozzle for enameled surfaces. Optimal distance: 30 50 cm.
90° angled special nozzle for undercarriage and wheel arches. Integrated guide shoes.

Click & Clean Brushes
Extension hose
Drain & Tube cleaner

For cars and other surfaces. Available in more shapes. 7 m extension hose increasing the working range. 15 m long tube cleaner for the cleaning of tubes and drains.

Water-sandblasting equipment
Patio Plus

For removal of paint and rust. Sand available from do-it-yourself shops.
Equipment for quick cleaning of patio/drive/flagstones.

Original instructions

17

10 Main Technical Data

Type

Super 130.2 Super 135.2 Super 140.2 Super 145.2

Electrical Specification

Rated voltage

V

230-240

Rated frequency

Hz

50

Rated power consumption kW

2.1

Current Protection class Protection degree

A
Class I/ Class II
IP XX

9.0 Class I IPX5

Hydraulic specification

Rated pressure

MPa/bar 12.5/125

13.5/135

14/140

Max. pressure

MPa/bar

13/130

14/140

14.5/145

Rated water flow

l/min/l/hr 7.5/450

7.0/420

6.8/410

Max. water flow

l/min/l/hr 8.3/500

8.3/500

Max. water inlet pressure

Mpa/bar

1/10

Max. water inlet temperature °C

Max. water inlet temp. suction mode

°C

60

20

Weight

kg

17.7

18.9

20.2

Hand-arm vibration according to ISO 5349-1:

Standard nozzle

m/s2

Sound pressure level LpA in accordance with ISO 3744
Guaranteed sound power level LWA in accordance with 2000/14/EC

dB(A) dB(A)

< 2.5 ±1 69.9 ±2
84

< 2.5 ±1 71.5 ±2
86

18

Original instructions

11 Declaration of Conformity

Declaration of Conformity

Product: Type:
The design of the unit corresponds to the following pertinent regulations:
Applied harmonised standards: Applied international standards and technical specifications: Name and address of the person authorised to compile the technical file:

High Pressure Washer

Gerni Super 130.2 S, Super 130.2, Super 135.2, Super 140.2, Super 140.2 Plus, Super 145.2 Plus

EC Machine Directive EC Low-voltage Directive EC EMC Directive RoHS Directive EC Noise Emission directive

2006/42/EC 2006/95/EC 2004/108/EC 2011/65/EC 2000/14/EC

EN 60335-2-79

IEC 60335-2-79

Anton Sørensen General Manager, Technical Operations EAPC

Identity and signature of the person empowered to draw up the declaration on behalf of the manufacturer:

Nilfisk-Advance A/S Sognevej 25 DK-2605 Brøndby
Anton Sørensen General Manager, Technical Operations EAPC

Place and date of the declaration

Nilfisk-Advance A/S Sognevej 25 DK-2605 Brøndby
Hadsund, November 1, 2013

Original instructions