eQuation 82748110 Electric Towel Dryer User Manual

eQuation 82748110 Electric Towel Dryer

Model

• TOWY
• 82748110

EAN

• 3276007372458

Important Safety

CAUTION: HOTAREAS.

• Some parts of this product can become very hot and cause burns.
• Particular attention has to be given where children and vulnerable people are present.

Warning: PLEASE READ CAREFULLY THIS MANUAL BEFORE USING THE APPLIANCE

DO NOT COVER!

• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• This appliance is not intended for use by individuals (including children) with reduced physical, sensory or mental capabilities, or individuals lacking experience or knowledge unless supervised or instructed in advance regarding the use of this appliance by the person in charge of their safety.
• Children should be monitored to ensure that they do not play with this appliance.
• In order to avoid a hazard for very young children, this appliance should be installed so that the lowest heated rail is at least 600 mm above the floor:
• Electric wiring must be performed by a qualified person in compliance with current local and national regulations, and with instructions of this manual.

WARNING

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules
• An energy management or power cut-off system is incompatible with this device. It damages the thermostat.
• The heater must not be located immediately below a socket outlet
• This device is IP23 protection and can be installed in zone 3 of the bathroom.
• The towel rail is to be installed so that switches and other controls cannot be touched by a person in the bath or shower.
• Do not install a shelf above the appliance.
• Keep a free space of 50 cm in front of the device.
• When heating for the first time, a slight odor may appear corresponding to the removal of any traces associated with the manufacture of the appliance.
• The surface of the appliance can be very hot, please pay special attention if you put delicate clothes on it (ex: Polyamide, …. ). Make sure the laundry does not fade before placing it on the towel warmer:
• This appliance is intented only for drying textiles washed in water
• Do not let children play with batteries
• Do not ingest batteries
• Non-rechargeable batteries are not to be recharged;
• Batteries are to be inserted with the correct polarity;
• Exhausted batteries are to be removed from the appliance and safely disposed of;
• If the appliance is to be stored unused for a long period, the battery should be removed;
• The supply terminals are not to be short-circuited.

Disposing of the packaging

• The packaging must be totally recycled, as stated by the recycling symbol printed on it.
• The various components of the packaging must not be thrown out in nature, but disposed of probably in compliance with local regulations.

Processing waste of electronic and electric devices at life-cycle end.

This image indicates that this product must not be disposed of with unsorted home trash. A system for disposal and special processing of used electric and electronic devices, mandatory to follow, has been implemented including the right to have vendors retrieve free-of-charge used appliances upon purchase of new appliances, as well as special collection of such waste by approved organisations.

For more information on this, you can contact your store or your town hall. Proper disposal of used electric and electronic appliances ensures their adequate processing and recycling in order to avoid damage to the environment and public health as well as to preserve natural resources.

CONNECTION

CONNECTION

• The appliance is double insulated and must not be earthed.

Connection with 2 pole plug (forbidden in France)

• Connect the plug to a 220-240V SO Hz wall socket

USE

Controls and functions

• All controls are available both on the heater panel and on the remote control;
• Remove the plastic tab to activate the remote control

On/ off switch

• An on/ off switch is located behind the device. (1 = ON)
• Use this only for a long shutdown (several days).

First start-up

When first powered on, it is necessary to adjust the time and day of the week. Set the On/ Off switch to 1, the device goes into standby mode.

1. Press Set twice, the day of the week flashes, adjust using keys ( + ) and –.
2. Press ok , hours are flashing, set with ( + ) and – keys
3. Press ok , minutes are flashing, set with( + ) and – keys

For each of the parameters, if there is no action within 5 seconds, the display goes to the next parameter; then exits the adjustment cycle.

Operating modes

several operating modes are available:

• Stand by: the heater is not working. The display shows 0.
• Continuous mode: The heater operates continuously. The power can be adjusted using the button.
• Temperature Setting: The device continuously monitors the setpoint temperature (desired temperature).
• Weekly Program: The device follows the saved schedules for each day of the week. These programs define at what time of day the radiator should follow the set temperature.

Continuous mode

1. From standby mode, press , the heater starts up, the display shows —
2. Press several times to adjust the power.
3. Press again to put the device on standby
   • The blower continues to ron for 30 seconds after turning off the heater.

Temperature setting

1. From standby mode, press , the heater starts up.
2. Set the desired temperature using + and – keys
3. Confirm by pressing ok.
4. Press to exit temperature setting mode and go back to continuous mode(display shows — )

In temperature setting mode, it is not possible to adjust the power; it is automatically adjusted according to the temperature to be reached.

Timer OFF

This function allows the heater to be put into standby after a user-defined time.

1. From standby mode, press , the heater starts up, the display shows —.
2. set the desired temperature using + and – keys.
3. Press , hours are flashing
4. Set the number of hours using + and – keys.
5. Confirm by pressing ok , minutes are flashing
6. set the number of minutes (by 15 minutes ranges) with + and – keys
7. Confirm by pressing ok
8. The display permanently shows the remaining time, when this time has elapsed, the heater goes into standby.
9. Press to put the device on standby before the programmed time.

Timer ON

This function allows the heater to be turned on after a user-defined time.

1. From standby mode, press , the heater starts up.
2. Press several times to set the power (continuous mode) or set the desired temperature.
3. Press again to put the heater on stand by.
4. Press , hours are flashing
5. Set the number of hours using + and – keys.
6. Confirm by pressing ok , minutes are flashing
7. set the number of minutes (by 15 minutes ranges with + and – keys
8. Confirm by pressing OK
9. The display permanently shows the remaining time, when this time has elapsed, the radiator starts up in the previously set mode.
10. Press to turn the device on before the programmed time.

Tip: While setting the timer, if there is no action within 5 seconds, the display changes to the next parameter and then exits the setting cycle.

Weekly program

The weekly program mode allows to define for each day of the week up to 2 heating periods (P1 and P2). Each period begins with a switch-on (ON) and ends with a standby (OFF)

1. From standby mode, hold the P key for 3 seconds, the programming screen is displayed, the P symbol and the first day of the week are flashing.
2. Set the day to program using and keys.
3. Press , the start and end times of the first period are displayed
4. Press ok , start time is flashing.
5. Set using + and – keys.
6. Press ok , minutes are flashing
7. Set using + and – keys.
8. Press ok , end time is flashing
9. Set using + and – keys.
10. – Press Ok , minutes are flashing
11. Set using + and – keys.
12. – Press Ok , Temperature is flashing
13. – Set using + and – keys.
14. – Press ok , period P2 is displayed
15. – Go back to point 3 to set period P2
16. – Go back to point 2 to program the other days

Tip

• To deactivate a heating period, press in order to set the start time and end time to OFF

• If a parameter should not be changed, press ok to go to the next.
  At any time, it is possible to exit programming mode by pressing P  for 3 seconds

• When programming for a day of the week is complete, the display automatically switches to the next

• Return to the factory values to erase all the settings (see below)

Activation OF Weekly Program

• Press P  to activate or deactivate the program mode, the indication P is displayed.

Open window detection

This function allows the heater to be put on standby after detecting a rapid drop in ambient temperature (10 ° C in 10 minutes), which generally corresponds to opening a window or a door.

1. From standby mode, press , the heater starts up.
2. Set the desired temperature if necessary, then confirm
3. Press , the indication is displayed as well as the reference temperature
4. Set the reference temperature using + and – keys
   • This reference temperature becomes the new setpoint temperature.
   • If the ambient temperature drops 10 ‘C below the reference temperature, the heater will go into standby because a window opening has been detected.
5. Press again to exit the Open window function.

Reset to factory values

• Press and OK simultaneously for 3 seconds to restore factory settings, the display shows FF. All programs and the day of the week and time setting are erased.

CARE

CARE

• Use a soft, dry cloth.
• For persistent stains, use a cloth dampened with soapy water and wipe immediately with a dry cloth.
• Regularly clean the filter blower and vacuum inlets and air outlet.

Tip: After 150 hours of use, the symbol appears and a beep sounds to remind to clean the filter. Press OK deactivate the symbol and the beep.

Replacing the remote control battery

1. Push the battery compartment latch in the direction of the arrow to remove the compartment
2. Insert 1 CR2032 3 V battery in the compartment. Make sure that the polarity ( + and – ) is respected.
3. Replace the battery compartment.

TROUBLESHOOTING

Malfunctions are often due to minor causes; please read the table below before contacting the after-sales service. This can save you time and avoid unnecessary expenses.

• If the problem persists, contact the after-sales service of your store.

Warranty

• The warranty does not cover problems related to improper installation, incorrect wiring or improper use.

CHARACTERISTICS

Guarantee

• 2-year guarantee

ADEO Services

• 135 Rue Sadi Carnot – CS 00001 59790 RONCHIN

Made in China 2023

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>