equation OH-1B Oil Heater Instruction Manual

June 10, 2024
equation

OH-1B Oil Heater

equation OH 1B Oil Heater Instruction Manualequation OH 1B Oil
Heater - icon

OH-1B Oil Heater

equation OH 1B Oil Heater - fig 14

WARNING
**
CAUTION!
HOT AREAS.**
Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are present.

PLEASE READ
CAREFULLY THIS MANUAL BEFORE USING THE APPLIANCE
equation OH 1B Oil Heater - icon 3DO NOT COVER !

  • Children of less than 3 years should be kept away unless continuously supervised.
  • Children aged from 3 years and less than 8 years shall only switch on/ off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance
  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. use this heater on a horizontal and stable surface, or fix it to the wall, as applicable.
  • To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 m from the air out
  • Use inside only
  • do not use this heater if it has been dropped;
  • do not use if there are visible signs of damage to the heater;
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
  • The heater must not be located immediately below a socket outlet
  • When heating for the first time, a slight odor may appear corresponding to the removal of any traces associated with the manufacture of the appliance.
  • Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
  • Do not use this heater near a bathtub, shower, or swimming pool.
  • Do not directly put clothes and other articles on the product to warm so as to prevent fire.
  • In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
  • Please disconnect power supply when you are out or the oil radiator is not used for a long time.
  • This heater is filled with a precise quantity of heat transfer fluid which is hazardous to health if swallowed.
  • Repairs requiring opening of the fluid container are only to be made by the manufacturer or his service agent.
  • In the event of a leak, please contact your installer and take any precautionary measure to avoid possible ingestion of the fluid by users, especially young children and vulnerable people.
  • When scrapping the heater, follow the regulations concerning the disposal of fluid
  • Do not let children play with batteries Do not ingest batteries
  • Non-rechargeable batteries are not to be recharged;
  • Batteries are to be inserted with the correct polarity;
  • Exhausted batteries are to be removed from the appliance and safely disposed of;

WARNING

  • If the appliance is to be stored unused for a long period, the battery should be removed;
  • The supply terminals are not to be short-circuited.

Disposing of the packaging

  • The packaging must be totally recycled, as stated by the recycling symbol printed on it. The various components of the packaging must not be thrown out in nature, but disposed of probably in compliance with local regulations.

Processing waste of electronic and electric devices at life-cycle end.
**** This image indicates that this product must not be disposed of with unsorted home trash. A system for disposal and special processing of used electric and electronic devices, mandatory to follow, has been implemented including the right to have vendors retrieve free-of-charge used appliances upon purchase of new appliances, as well as special collection of such waste by approved organizations. For more information on this, you can contact your store or your town hall. Proper disposal of used electric and electronic appliances ensures their adequate processing and recycling in order to avoid damage to the environment and public health as well as to preserve natural resources.

INSTALLATION

Rolls Assembly

equation OH 1B Oil Heater - fig

Connection

  • This device is mobile type and can be moved while respecting the safety instructions.
  • The appliance must be earthed.
  • Connect the plug to a 220-240V 50/60Hz wall socket
  • Unplug the appliance when it is not in operation
  • A reel allows the cable to be stored safely

Important !

  • Make sure to unwind the cable completely before plugging it in.
  • Never handle the radiator while holding it by the reel

USE

equation OH 1B Oil Heater - fig 4

All controls are available both on the heater panel and on the remote control;
Remove the plastic tab to activate the remote control.

ON / OFF switch
An on / off switch is located behind the control box of the device.
Use this only for a long shutdown (several days).
It may be necessary to re-set the date and time after long shutdown.
When the switching ON, the device is automatically in standby mode

First start-up
When first powered on, it is necessary to adjust the time and the day of the week.

  1. Press to exit standby mode, hour is flashing
  2. Set hour using + and – buttons.
  3. Press SET, minutes are flashing.
  4. Set using + and – buttons.
  5. Press SET, day of the week is flashing.
  6. Set using + and – buttons.
1 2 3 4 5 6 7
Monday Tuesday Wednesday Thursday Friday Saturday Sunday

Press SET to valid.
After setting, manual mode is activated.

Operation modes

Several operation modes are available :

  • Standby mode : The device is off, it only heats up if the Frost protection mode is activated.
  • Manual mode: The device continuously monitors the setpoint temperature (desired temperature) using one of the 3 powers chosen.
  • Program mode: The device follows the recorded programs for the week or the weekend. These programs define at what times of the day the heater must follow the  setpoint temperature or be switched off.
    It is essential to have set the time and the day to use the program mode.

Standby / Switching on the device

  1. Press ****to put the device in standby.
  2. Press ****again to turn on the device.

Selection of the operation mode

  • Press the MODE key several times to choose the desired mode:

equation OH 1B Oil Heater - fig 7

Manual mode

  1. Press MODE several times to choose the power
  2. Use the + and – keys to adjust the setpoint temperature (desired temperature).

Continuous mode

  • In Manual mode, press the SET button to activate Continuous mode. In this mode, the appliance heats up continuously, regardless of the setpoint temperature. The HI  indication  replaces the temperature display.
  • Use the + and – keys to exit continuous mode and set a new setpoint temperature.
    After 12 hours of continuous mode, the device automatically returns to standby

Anti Frost protection

  • When the appliance is on standby mode, if the ambient temperature drops below 5°C, the anti frost protection is activated automatically, and the indicator is displayed.  As soon as the temperature grows above 7°C, the protection is deactivated and the device returns to standby.

Program Mode

  • Program mode allows to define at what times of the day the heater must follow the setpoint temperature or be on standby. It is possible to define a program for the week (days 1 to 5) and another for the weekend (days 6 and 7).

Editing Programs

  1. Press MODE several times to choose Programming mode. Each bar corresponds to a period of one hour.
  2. Press SET, the display shows “12345” (week program) and the first bar is flashing (period from 0h to 1h),
  3. Press + to define that the device must follow the setpoint temperature during this period, or – to define that the device must be on standby during this period.
  4. The following bar flashes (period from 1 hour to 2 hours) press + or – to set this period.
  5. Proceed in the same way for each period of the day
  6. Press SET, the display shows “67” (weekend program) and the first bar is flashing (period from Oh to 1h),
  7. Press + or = to set this period.
  8. The following bar is flashing (period from 1 hour to 2 hours) press + or = to set this period.
  9. Proceed in the same way for each period of the day
  10. Press SET to exit edit mode.

Timer
The Timer function allows the heater to be put into standby mode after a user- defined time.

  1. From standby mode, press to turn on the device.
  2. Press MODE several times to choose the power in Manual mode
  3. Use the + and – keys to adjust the setpoint temperature
  4. Press , the M symbol is flashing
  5. Set the number of hours using the + and – keys (one bar corresponds to one hour)
  6. Confirm with the key.
  7. The display now shows a number of bars corresponding to the number of hours left before standby. A bar will be erased every hour.
    While setting the timer, if there is no action within 10 seconds, the device exits the setting cycle.
    Press for more than 3 seconds to cancel the timer

Child lock
The controls can be locked to prevent unintentional use, especially by children. To do this, simultaneously press the + and – buttons on the control panel or press the button  on the remote control for more than 3 seconds. Proceed in the same way to unlock the controls.

Anti-tilt switch
An anti-tilt switch is located in the device, it automatically cuts off the power in the event of a fall or movement of the device.

Thermal cutoff
A thermal cutoff protection switches off heating automatically in case of severe overheating. In this case, turn off the device, eliminate the cause of the overheating, and allow it to cool before using again.

CARE

  • Remove the plug from the socket before cleaning. There is a risk of electric shock. Wait until the oil-filled radiator has cooled down. Otherwise, there is a risk of burn  injuries.
  • Clean the radiator at regular intervals. Use a slightly damp cloth and never use cleaning agents or solvents that react with plastics.

Replacing the remote control battery

  1. Push the battery compartment latch in the direction of the arrow to remove the compartment
  2. Insert 1 CR2032 3 V battery in the compartment. Make sure that the polarity (“+” and “-”) is respected.
  3. Replace the battery compartment

TROUBLESHOOTING

Malfunctions are often due to minor causes; please read the table below before contacting the after-sales service. This can save you time and avoid unnecessary expenses.

Problem Causes, Solutions
The heater does not turn on. Check that the device is electrically powered.

Check the heater is vertically placed on a stable surface.
The heater doesn’t heat| Check the temperature of the room: if it is too high compare to the thermostat setting, the unit does not heat.
The device makes a liquid noise when it is handled.| During unpacking or installation, it is normal to hear the fluid flow within the device.

MAINTENANCE

  • Maintenance work is required if the radiator has been damaged, liquids or objects have got inside the device, the radiator has been exposed to rain or moisture or if the  radiator is not functioning properly or has been dropped.
  • If you notice any smoke, unusual noises or smells, switch off the oil-filled radiator immediately and remove the plug from the socket. If this happens, you must stop using  the oil-filled radiator until it has been checked by a specialist.
  • All maintenance work should only be carried out by qualified specialists.
  • Never open the housing of the oil-filled radiator.

CHARACTERISTICS

Model Identifier HD972EB-A9QL
Rated voltage 220-240 V
Item Symbol
Heat output
Rated heat output P nom
Minimum heat output P min
Maximum continuous heat output P Pmax,c
Auxiliary Electricity Consumption
At nominal heat output el max
At minimum heat output el min
In standby mode el sb
Item Unit

Type of heat input, for electric storage local space heaters only (select one)
Manual thermal control of the load with integrated thermostat| No
Manual thermal control of the load with reception of information on the temperature of the room and/or outside| No
Electronic thermal control of the load with information on room and/or outside temperature| No
Thermal power can be regulated by fan| No
Type of heat output/room temperature control
Single stage heat output and no room temperature control| No
Two or more manual steps, no room temperature control| No
Room temperature control with mechanical thermostat| No
Electronic room temperature control| No
Electronic room temperature control and daily timer| No
Electronic room temperature control and weekly timer| Yes
Other control options
Room temperature control with presence detection| No
Room temperature control with open window detection| No
Remote control option| No
Adaptive activation control| No
Activation duration restriction| Yes
Black globe sensor| No
Contact Details| ADEO Services -135 Rue Sadi Carnot – 59790 – RONCHI N – FRANCE

SPARE PARTS

Some parts of this heater can be ordered from your store:

equation OH 1B Oil Heater - fig 13

Description Reference to order
Rolls kit 3276007272406
Remote Control 3276007376272

WARRANTY

Terms and conditions of the ADEO SERVICES manufacturer warranty
Ado Services offers a manufacturer warranty on its products.

The scope of the Adel Services manufacturer warranty:
Ado Services products are designed and built to provide quality performance for normal use. If a product proves to be defective during the warranty period under normal  use, it is Ado Services’ responsibility to repair or replace it. The Ado Services warranty covers the repair or replacement (at the discretion of Adeo Services) of your device  marketed by Ado Services if it proves to be defective due to a material or manufacturing defect during the warranty period. In case of unavailability of a part required for  proper functioning of the product, Ado Services commits to replacing it with a part of equivalent characteristics and performance levels The implementation of this  warranty does not affect the exercise of your rights under the legal warranties provided by the civic l code and the consumer code.

Cases excluded from the coverage of the Ado Services manufacturer warranty:
The Ado Services manufacturer warranty is not intended to apply in the cases listed below:

  • Normal wear and tear of the product and/or its components
  • Accidental damage (due to dropping the product, impact or improper installation of the product)
  • Damage resulting from use that does not comply with the information in the user manual and/or packaging (e.g. incorrect power supply voltage)
  • Damage caused by failure to comply with the product maintenance recommendations.
  • Damage caused by external sources such as transportation, weather, power failure or power surges.
  • Cosmetic damage, including, but not limited to, scratches, scuffs, or broken plastic components,
  • Failures caused by Acts of God (events beyond the control of Ado Services, unforeseeable at the time of sale of the product and the effects of which could not be  avoided by appropriate measures (e.g. natural disasters).
  • Failures caused by:
    • Negligent use, misuse, mishandling or careless use of the product.
    • Use not in accordance with the product user manual.
    • Use of the product for purposes other than normal domestic use in the country where it was purchased.
    • Use of parts that are not assembled or installed in accordance with Adel Services installation instructions.
    • Use of parts and accessories that are not genuine Ado Services components.
    • Faulty installation or assembly.
    • Repairs or modifications performed by parties other than those authorized by Ado Services or its authorized agents.
  • The warranty will also not be valid if the serial number or the nameplate of the product (if the product has a nameplate) is removed or defaced.
  • If Ado Services receives information from competent public authorities that the product has been stolen.

What are the terms and conditions for implementing the warranty?
The terms and conditions for implementing the Ado Services warranty are as follows

  • The warranty takes effect on the date of purchase (or on the date of delivery if later).

  • A proof of delivery/purchase is required prior to performing any operation on your device under warranty.
    Please note that without this proof, any work to be done will be subject to an estimate, which must be accepted by the customer before any work can be done. Please  keep your purchase receipt or delivery note.

  • All work will be performed by Adeo Services or its authorized service providers.

  • Any replaced part becomes the property of Adeo Services

  • The repair or replacement of your device under warranty does not extend the warranty period.

  • The warranty does not affect the exercise of your rights under the legal warranties provided by the civil code and the consumer code.

  • To make use of this warranty, you must contact the brand company from which you purchased your product.

Date of entry into force of the warranty:
The Ado Services warranty takes effect on the date of purchase or the date of delivery of your product, whichever is later.

Geographic scope of Adeo Services warranty:
The warranty is valid in the country of purchase of the product.
If you use your device in a country other than the one in which you purchased it, the warranty may be invalidated. In this case, please contact the brand company in the  country of origin where you purchased the product who will study the warranty claim on a case by case basis.

Fate of Adeo Services warranty in case of resale of the product:
In case of resale of the product during its warranty period, the warranty remains valid for the benefit of the buyer and can be implemented by the latter provided however:
That the proof of original purchase of the product is brought along, That the proof of proof of proper functioning of the product at the time of the resale is brought along, That the terms and conditions of implementation of the warranty as detailed within the present document are met. It is specified that the resale of the product has no effect  on the warranty period remaining at the date of resale. Thus, the buyer of the resold product can claim the benefit of the Ado Services warranty within the limit of the remaining validity time of the warranty at the date of the resale.

Do not use this heater if it has been dropped;
Do not use if there are visible signs of damage to the heater;
Use this heater on a horizontal and stable surface, or fix it to the wall, as applicable.
WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
WARNING: To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 m from the air outlet.

ADEO Services – 135 Rue Said Carnot
CS 00001 – 59790 RONCHIN below is the warning insert

Documents / Resources

| equation OH-1B Oil Heater [pdf] Instruction Manual
OH-1B, HD972EB-A9QL, 89160076, 3276007364682, OH-1B-CY, HD972EB-A9QL CY, 89160088, 3276007364781, OH-1B Oil Heater, Oil Heater, OH-1B Heater
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals