equation L2 OPEN 9KW MANNU Pellet Stove Instruction Manual

HAND

Installation Manual,
Legal & Safety Instructions

5-year warranty, See conditions of application in the warranty booklet
This product is not suitable for primary heating purposes
2022R08P05-0002-2022/07-V02

L2 OPEN 9KW MANNU Pellet Stove

INTRODUCTION

Thank you for buying this product. We advise you to read all the instructions in the packaging carefully.
The document ”1” contains installation instructions, legal notices and safety instructions, as well as all the technical characteristics applicable to the product.
In the product manual “2” of the product you will find legal notices and safety instructions and the instructions for use and maintenance.
We have designed this product to bring you complete satisfaction. If you need help, your store team is at your disposal to help you.

WARNINGS

• These instructions are an integral part of the product: please ensure that they always accompany the device, including in the event of sale to another owner or user, or in the event of transfer to another location. If these booklets were to be damaged or lost, ask for other copies from your store.

• The symbols  and visible on the product and the manuals mean that you must carefully read the instructions and the technical information contained in these manuals before installing, using and intervention on the product.

• This product must be reserved for the use for which it has been expressly carried out. Any contractual and extra contractual liability of the manufacturer, in the event of damage caused to people, animals or goods, due to errors in installation, adjustment, maintenance and incorrect use, is excluded.

• The installation must be executed by qualified and authorized personnel, which will assume all the responsibility for the final installation as well as the proper functioning of the
  installed product.

• It is necessary to comply with all national regulations, in particular those which refer to national and European standards, during the installation of the device

• After removing the packaging, please ensure that the content is intact and that nothing is missing. If necessary, please contact the store.

• All the electrical parts that make up the product and which guarantee its proper functioning, will have to be replaced by original parts and only by an approved technical assistance center.

• This stove is controlled by an electronic card which allows completely automatic and controlled combustion; The control unit indeed regulates the ignition phase, 5 power levels and the stop phase, guaranteeing a safe operation of the stove;

ATTENTION !

• This device can be used by children aged 8 years or more, by people whose physical, sensory or mental capacities are reduced, or people without experience or knowledge, only if
  they have benefited from surveillance or prior instructions regarding the use of the device safely, and that they include the potential dangers linked to the use of the device.

• Children should not play with the device. Cleaning and maintenance should not be carried out by unattended children.

• If the power cable is damaged, it must be replaced by the manufacturer, its after-sales service or similar qualification persons in order to avoid a danger.

• It is recommended to position the power cable so that it does not come into contact with the hot parts of the device.

• The plug must be accessible after installation.

• Never cover the body of the stove in any way or obstruct the slots on the upper side when the device is in operation.

• It is prohibited to reduce dimensions or obstruct the ventilation openings of the installation part. The ventilation openings are essential for correct combustion.

• The device should not be used as an incinerator, nor use fuels other than pellets.

• Do not leave the elements of the packaging within the reach of children or disabled people, not assisted.

• When the device is in working order, the household door must always remain closed.

• It is forbidden to install the stove in bedrooms or in explosive atmosphere environments.

• During the operation, certain parts of the stove (door, handle, sides) can reach high temperatures. Therefore, you must be very careful and take the necessary precautions, especially in the presence of children, the elderly, disabled and animals.

• It is recommended, at the maximum operating power of the stove, the use of gloves to handle the pellets loading door and the opening handle of the door.

• Caution: Radiation, especially through glass surfaces, can ignite combustible objects around the device. Observe the minimum distance between these objects and the device.

• Check the possible presence of obstructions before turning on a device after a long period of inactivity.

• The stove was designed to be used in any climate condition. However, in the event of a particularly unfavorable climate (strong wind, gel), security systems could trigger causing the stove stop. If this is verified, contact the technical assistance service and especially not to deactivate the security systems.

• It is prohibited to connect more than one device to the same smoke duct.

• In the event of a fire, disconnect the power supply, use a standard extinguisher and, if necessary, call the firefighters. Then contact the approved service center.

• This device should not be used as a waste incinerator

• Never use gasoline, kerosene, charcoal lighter fluid, alcohol or similar liquids to ignite or re-ignite any combustion in the appliance. Keep all such liquids away from the device while in use.

• During filling, ensuring that the bag of pellets does not come into contact with the device

• Regular cleaning of the device, the connection duct and the smoke duct is compulsory, respecting the operating mode and the frequency described in this manual.

• The remote control works using a button battery:

  • Use only the recommended battery type
  • The battery contacts should not be short-circuited;
  • The battery must be inserted with the correct polarity;
  • The battery must be removed from the device before it is rebuilt;
  • Non -rechargeable batteries should not be recharged;
  • Rechargeable batteries are to be removed from the appliance before being charged
  • Different types of batteries or new and used batteries are not to be mixed
  • used batteries or leaks must be removed from the device and eliminated safely;
  • Do not ingest the battery;
  • If the device has to remain unused for a long time, remove the battery;
  • Keep the batteries out of the reach of children.
  • Do not let the batteries drag. There is a risk if children or animals swallow them.
  • Consult a doctor immediately if a battery is swallowed.
  • Never throw the batteries in fire or water.
  • WARNING

KEEP THE BUTTON BATTERY OUT OF THE REACH OF CHILDREN
Swallowing can lead to chemical burns, perforation of soft tissue, and death. Severe burns can occur within 2 hours of ingestion. Seek medical attention immediately.

RESPONSIBILITIES

With the delivery of this manual, we decline any responsibility, both civil and criminal, in the event of accidents resulting from partial or total non- compliance with the instructions contained therein. We decline any responsibility arising from incorrect use of the stove, user incorrect use, unauthorized modifications and/or repairs, or the use of non -original spare parts for this model.
The manufacturer declines any direct or indirect civil or criminal liability due to:

• Bad maintenance;
• Non-compliance with the instructions contained in the manuals;
• Use not in accordance with safety instructions;
• Installation not in accordance with the regulations in force in the country;
• Installation by unskilled and not trained personnel;
• Changes and repairs not authorized by the manufacturer;
• Use of non -original spare parts;
• Exceptional events (ex: “natural disaster, stripping of waters, electrical overvoltage, war/riot, problem of construction of the house, …)

Processing waste of electronic and electric devices at life-cycle end.
This image indicates that this product must not be disposed of with unsorted home trash.
A system for disposal and special processing of used electric and electronic devices, mandatory to follow, has been implemented including the right to have vendors retrieve free-of-charge used appliances upon purchase of new appliances, as well as special collection of such waste by approved organisations.
For more information on this, you can contact your store or your town hall. Proper disposal of used electric and electronic appliances ensures their adequate processing and recycling in order to avoid damage to the environment and public health as well as to preserve natural resources.

INSTALLATION

The floor of the room where the stove will be installed must be of size and structure sufficient to support its weight.
If an existing construction does not meet this prerequisite, adequate measures (for example, the installation of a load distribution plate) must be taken to allow the ground to support the device.
In the presence of a wooden floor, provide a protective surface in accordance with the regulations in force in the country.
The wall must be made up of incombustible materials.
Maintain a minimum rear distance of 20 cm, a lateral distance of 40 cm and a front distance of 100 cm, any wall and any fuel object. These distances must be respected to allow the technician to carry out maintenance, and for the safety of the product itself. In the presence of particularly delicate objects such as furniture, curtains, sofas, considerably increase the distance from the stove. For proper functioning and good distribution of the temperature, the stove must be placed in a place where the necessary air can circulate for the combustion of the pellets (about 40 m3/h must be available according to the installation standard and according to the regulations in force in the country). The volume of the environment should not be less than 20 m3.
It is mandatory to provide an external air intake which allows the combustion air supply necessary for the proper functioning of the stove.
It is recommended to connect the air necessary for combustion directly to the external air inlet, with a Ø 40 mm hose, with a maximum length of 2 linear meters, each curve of the pipe is equivalent to a leak of a linear meter (diagram opposite). It is possible to take the air directly in the room where the stove is installed, in this case, the air intake of the room must have a total net minimum surface of 100 cm² protected by an external grid which should not be obstructed and must be cleaned periodically. The surface must be increased accordingly if there are other active generators inside the room (for example: electric fan for stammering air, hood, other stoves, etc.) , which can depress the environment.
The air inlet grids must be positioned so that they cannot block or close accidentally.

CHIMNEY

• The indications below are intended to give information on the construction of a good chimney, but it must in no case be considered as a substitute for the standards in force in the country of installation, standards of which the qualified manufacturer must be in possession. The manufacturer of the stove declines any civil or criminal liability concerning the dysfunction of the stove due to a poor
  • sized chimney and/or not in accordance with the regulations in force which must be respected.
• The chimney must be built according to manufacturing standards (≥ T200), must be vertical without bottlenecks, must be resistant to condensation and must be resistant to soot fire. It must be isolated from the outside to avoid cooling of smoke and must be equipped with a condensate drain. If the chimney is a concrete cavity, it must be tubed.
• The chimney must be able to be inspected for cleaning and must be spaced flammable and/or combustible materials.
• The chimney must always be clean, any residue of soot reduces the section of the fireplace, compromises the draw, and can generate a hole fire. Clean up the smoke duct and the chimney by a specialized sweater at least once a year and before lighting the stove after periods of inactivity. Provide a visit hatch at the base of the chimney flue to be able to carry out periodic checks and sweeping. The absence of cleaning will affect the proper functioning of the device.
• Check, by means of appropriate instruments, that the cold draft is at least 4 Pa .
• Imperatively control that a backflow protection of the roof output has been installed, in accordance with the standards in force
• Check the correct configurations using the standard EN 13384-1

CONNECTION TO THE CHIMNEY

• The connection between the stove and the chimney must be made with a pipe 80 or 100 mm diameter with a maximum length determined by a calculation note.

• For each elbow of 45 °, consider a loss equal to one meter of linear section.
  Example: 5m maximum length with 2 elbows = 5m – 2m = 3m (the tee with tee cap does not count for a elbow)

• The pipe must have a smooth inner surface and resist heat (quality ≥ T200).

• The first change of direction must take place after at least 1.5 meters of vertical section.

• The use of flexible metal pipes, in fiberociment, or aluminum is prohibited. The duct must be as direct and as vertical as possible to avoid soiling and promote natural draught.

• Provide the basis of the smoke an inspection for periodic controls.

• It is prohibited to connect more than one device to the same smoke duct.

• Maintain the smoke duct at a sufficient distance from any flammable or thermotensile element.

Rear connection

The stove is supplied by default with the rear flue pipe.

• Secure the adaptor to the back of the stove with the screws provided and a high temperature silicone gasket.
• Use a tee with tee cap (80mm input) to connect the pipe to the stove

Top connection
Since the stove is designed for the evacuation of smoke from the rear, it is necessary to modify it to connect it from the top.

• remove the left side panel to access the smoke box.
  Remove the top plate of the smoke box.
  Fix the plate at the back of the smoke box by inserting the gasket.
  Secure the nozzle to the smoke box with the screws and a high temperature silicone gasket.
  Remove the lid from the top of the stove.
  Pass the pipe and fit it on the adaptor using a sleeve if necessary

ELECTRICAL CONNECTION

INSERTING THE REMOTE CONTROL BATTERY

THERMOSTATIC PROBE

The room temperature is detected thanks to the probe located on the back of the device. This probe must be deployed so as not to be affected by the temperature of the stove.

EXTERNAL ROOM THERMOSTAT

The stove is equipped with a connector for the connection of an external thermostat. This thermostat allows you to manage the functioning of the stove through the wall thermostat rather than through the probe at the back of the stove. The thermostat must be of the “dry contact” type to turn on or turn off the stove according to heat needs. Configure this thermostat to manage a pellet stove.

Setting the stove to receive information from the external thermostat
For the external thermostat to be recognized by the stove, the technical menu parameter CP09 must be set to On.

• Press several times to display menu 04 (technical menu)

• Press several times to display the CP09 parameter

• Press to confirm

• Press to activate the external thermostat

• Press to confirm

SETTING THE BEHAVIOR OF THE THERMOSTAT

The thermostat can behave in two different modes:

• Eco mode (StoF)(by default): when the set temperature is reached, the stove goes down to power 1 and stays on this power without switching off.
• Eco Stop mode (St01…): when the set temperature is exceeded, the stove goes down to power 1 then switches off.

Change behavior mode:

• Press repeatedly to display menu 04 (technical menu)

• Press several times to display the
  CP08 parameter

• Press to confirm

• Press to activate the Eco Stop mode and choose the number of degrees that will trigger the shutdown of the stove.

• Example: if the temperature of 20°C has been set and parameter St02 chosen, the stove will stop when the temperature of 22° is reached

• Press to confirm

CHARACTERISTICS

Table 1

output
p| COG| co| NOx| p| COG| co| NOx
[x] mg/Nm3(13 % 02)| [x] mg/Nm3(13 % 02)
Wood logs with moisture content s 25 %| No| No| | | | | | | | |
Compressed wood with moisture content < 12 %| Yes| No| 903| 10| 2| 21| 130| 18| 2| 197| 123
Other woody biomass| No| No| | | | | | | | |
Non-woody biomass| No| No| | | | | | | | |
Anthracite and drv steam coal| No| No| | | | | | | | |
Hard coke| No| No| | | | | | | | |
Low temperature coke| No| No| | | | | | | | |
Bituminous coal| No| No| | | | | | | | |
Lignite briquettes| No| No| | | | | | | | |
Peat briquettes| No| No| | | | | | | | |
Blended fossil fuel briquettes| No| No| | | | | | | | |
Other fossil fuel| No| No| | | | | | | | |
Blended biomass and fossil fuel briquettes| No| No| | | | | | | | |
Other blend of biomass and solid fuel| No| No| | | | | | | | |

Characteristics when operating with the preferred fuel only

Auxiliary Electricity Consumption
At nominal heat output| el max| kW| 0,048
At minimum heat output| el min| kW| 0,022
In standby mode| elsb| kW| 0,003
Power required by standing pilot
Power required by the pilot (if applicable)| P pilot| kW| —
Useful efficiency (NCV as received)
Useful energy efficiency at nominal heat output| ηth,nom| %| 94,2
Useful energy efficiency at minimal load| ηth,min| %| 95
Type of heat output/room temperature control
Single stage heat output and no room temperature control| No
Two or more manual steps, no room temperature control| No
Room temperature control with mechanical thermostat| No
Electronic room temperature control| NO
Electronic room temperature control and daily timer| No
Electronic room temperature control and weekly timer| Yes
Other control options
Room temperature control with presence detection| No
Room temperature control with open window detection| No
Remote control| No
Contact Details                                IADEO Services – 135 Rue Sadi Carnot – 59790 – RONCHIN – FRANCE

Table 3

Emission of volatile organic compounds to an oxygen content of 13 % with the useful nominal power| COVnom (13 % 02)| mg/m3| 2
Emission of volatile organic compounds to an oxygen content of 13 % with useful power at
partial load| COVpart (13 % 02)| mg/m3| 2
Particle emission to an oxygen content of 13 % with the useful nominal power, measured by a heating filter| PMnom (13 % 02)| mg/m3| 10
Particle emission to an oxygen content of 13 % with useful power at partial load, measured by a heating filter| PMpart (13 % 02)| mg/m3| 18
Minimal draught with nominal useful power| pnom| Pa| 8
Minimum draught with useful power at partial load| Ppart| Pa| 4
Safety distance between the rear and the combustible material| dR| mm| 200
Safety distance between sides and combustible material| dS| mm| 400
Safety distance between the top and the combustible material in the ceiling| dC| mm| 1500
Safety distance between the front and the combustible material| dp| mm| 1000
Auxiliary electrical energy consumption| w| w| 300
Nominal useful smoke outlet temperature| Tnom                     ·| c| 1,129
Smoke output temperature with useful power at partial load| Tpart ·| c| 764
Mass flow of fumes with nominal useful power| –| g/s| 52
Mass flow of fumes with useful power at partial load| –| g/s| 3
C02 concentration with nominal useful power| –| %| 129
CO2 concentration with useful power at partial load| –| %| 88
Diameter of the evacuation nozzle| dbuse| mm| 80
General dimensions of the device (width, height, depth)| L, H,W| mm| 475 x 1000 x 533
Weight of the device| m| kg| 886
Supply voltage| u| v-| 230
Supply frequency| f| Hz| 50

Test conditions : announced performances are sensitive to many parameters, and mainly the test pellet quality, and lab equipments and setup. The manufacturer can provide some specific settings in order to adapt to the test conditions. Also, please note that announced performances will be reached after several working hours at nominal power (stove  preconditioning), and if possible at least 15 hours.

WARRANTY

Terms and conditions of the ADEO SERVICES manufacturer warranty
Adeo Services offers a manufacturer warranty on its products.

The scope of the Adeo Services manufacturer warranty:
Adeo Services products are designed and built to provide quality performance for normal use. If a product proves to be defective during the warranty period under normal use, it is
Adeo Services’ responsibility to repair or replace it. The Adeo Services warranty covers the repair or replacement (at the discretion of Adeo Services) of your device marketed by Adeo Services if it proves to be defective due to a material or manufacturing defect during the warranty period. In case of unavailability of a part required for proper functioning of the product, Adeo Services commits to replacing it with a part of equivalent characteristics and performance levels The implementation of this warranty does not affect the exercise of your rights under the legal warranties provided by the civil code and the consumer code.
Cases excluded from the coverage of the Adeo Services manufacturer warranty: The Adeo Services manufacturer warranty is not intended to apply in the cases listedbelow:

• Normal wear and tear of the product and/or its components
• Accidental damage (due to dropping the product, impact or improper installation of the product)
• Damage resulting from use that does not comply with the information in the user manual and/or packaging (e.g. incorrect power supply voltage)
• Damage caused by failure to comply with the product maintenance recommendations.
• Damage caused by external sources such as transportation, weather, power failure or power surges.
• Cosmetic damage, including, but not limited to, scratches, scuffs, or broken plastic components,
• Failures caused by Acts of God (events beyond the control of Adeo Services, unforeseeable at the time of sale of the product and the effects of which could not be avoided by appropriate measures (e.g. natural disasters).
• Failures caused by:
  • Negligent use, misuse, mishandling or careless use of the product.
  • Use not in accordance with the product user manual.
  • Use of the product for purposes other than normal domestic use in the country where it was purchased.
  • Use of parts that are not assembled or installed in accordance with Adeo Services installation instructions.
  • Use of parts and accessories that are not genuine Adeo Services components.
  • Faulty installation or assembly.
  • Repairs or modifications performed by parties other than those authorized by Adeo Services or its authorized agents.
• The warranty will also not be valid if the serial number or the nameplate of the product (if the product has a nameplate) is removed or defaced.
• If Adeo Services receives information from competent public authorities that the product has been stolen.

What are the terms and conditions for implementing the warranty?
The terms and conditions for implementing the Adeo Services warranty are as follows

• The warranty takes effect on the date of purchase (or on the date of delivery if later).

• A proof of delivery/purchase is required prior to performing any operation on your device under warranty. Please note that without this proof, any work to be done will be  subject to an estimate, which must be accepted by the customer before any work can be done.
  Please keep your purchase receipt or delivery note.

• All work will be performed by Adeo Services or its authorized service providers.

• Any replaced part becomes the property of Adeo Services

• The repair or replacement of your device under warranty does not extend the warranty period.

• The warranty does not affect the exercise of your rights under the legal warranties provided by the civil code and the consumer code.

• To make use of this warranty, you must contact the brand company from which you purchased your product.

Date of entry into force of the warranty:
The Adeo Services warranty takes effect on the date of first start up.

Geographic scope of Adeo Services warranty:
The warranty is valid in the country of purchase of the product.
If you use your device in a country other than the one in which you purchased it, the warranty may be invalidated. In this case, please contact the brand company in the country of origin where you purchased the product who will study the warranty claim on a case by case basis.

Fate of Adeo Services warranty in case of resale of the product:
In case of resale of the product during its warranty period, the warranty remains valid for the benefit of the buyer and can be implemented by the latter provided however:
That the proof of original purchase of the product is brought along,
That the proof of proof of proper functioning of the product at the time of the resale is brought along, That the terms and conditions of implementation of the warranty as detailed within the present document are met. It is specified that the resale of the product has no effect on the warranty period remaining at the date of resale. Thus, the buyer of the resold product can claim the benefit of the Adeo Services warranty within the limit of the remaining validity time of the warranty at the date of the resale.

Adeo Services Manufacturer’s Warranty: Special Conditions

• See the attached Warranty booklet.

Made in Italy
ADEO SERVICES – 135 RUE SADI CARNOT – CS 00001 – 59790 RONCHIN – FRANCE

Documents / Resources

| equation L2 OPEN 9KW MANNU Pellet Stove [pdf] Instruction Manual
L2 OPEN 9KW MANNU Pellet Stove, L2 OPEN 9KW, MANNU Pellet Stove, Pellet Stove, Stove
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>