bikefinder Gen2 Tracker User Manual
- June 13, 2024
- bikefinder
Table of Contents
bikefinder Gen2 Tracker
Product Information
- Product name: BikeFinder Gen2 tracker
- Model: BFG2
- Network frequency: LTE 700-950/1700-2210MHz, WiFi/BLE 2.4GHz
- Satellite system: GPS
- Battery: Rechargeable, detachable 650 mAh Li-Ion battery
- Compatibility: Handlebar inner diameter: 15.01-19.9 mm (mount without expansion mechanism adapter), 20.0-27.0 mm (mount with expansion mechanism adapter)
- Contact: Contact global customer service via the app or email us at support@bikefinder.com
- Limitations and warranty: For full terms and conditions, visit www.bikefinder.com/terms. BikeFinder privacy policy can be found at www.bikefinder.com/privacy. More information and video instructions are available at www.bikefinder.com/manual
About
This manual describes the proper use of the BikeFinder Gen2 tracker and its
accessories. Make sure to read this user manual before installation and
activation of the tracker. Ensure that all warnings are read and understood
before use.
Technical specifications
- Product name: BikeFinder Gen2 tracker
- Model: BFG2
- Network frequency: LTE 700-950/1700-2210MHz, WiFi/BLE 2.4GHz
- Satellite system: GPS
- Battery Rechargeable: Detachable 650 mAh Li-Ion battery
Compatibility
Handlebar inner diameter:
- 15.01-19.9 mm (mount without expansion mechanism adapter).
- 20.0-27.0 mm (mount with expansion mechanism adapter).
Note: This device is only intended to be mounted in the handlebar of a
bike.
The tracker requires a BikeFinder subscription to function.
Contact
Contact global customer service via the app or email us at
support@bikefinder.com.
Limitations and warranty
General Safety Precautions
- Do not bend the tracker module.
- Do not bend the battery module more than 45°.
- Do not insert tools or pointy objects, other than those included, into other openings in the tracker than explicitly described here.
- Do not open or tamper with any internal components.
- Do not expose the tracker to water submersion or high-pressure water jets.
- Do not drop the tracker onto hard surfaces or expose it to high-energy impacts.
- Do not charge the tracker outside of the allowed charging temperature (below 0°C or higher than 45°C).
- Keep tracker and accessories away from high-pressure places, potentially explosive atmospheres, and extreme temperature conditions (below -20°C or higher than 45°C).
- Keep away from medical electronic equipment.
For full terms and conditions:
www.bikefinder.com/terms
BikeFinder privacy policy:
www.bikefinder.com/privacy
More information and video instructions:
www.bikefinder.com/manual
Getting started information:
Installation Steps
Connect the battery module to the tracker module
Align the tracker and battery module as shown in the picture on the right.
Push the two modules together until a click sound is heard. The battery module
must be connected to the tracker module for the tracker to take charge and for
the tracker to work.
Note: If you need to disassemble the battery module from tracker, use the tool (pincher) that comes with the product and follow the steps below:
- Pinch the tool at area to open the tooltip as shown in picture a.
- Slide the tool over the two holes, then release the tool. The pinch should now sit on the tracker module as shown in picture b.
- Hold tracker in one hand and pinch the tool as shown in picture c, then pull out the battery module.
Charge the tracker
Connect charging cable to a power source with 5 V and minimum 0.5 A output.
Remove the front cover, then connect the charging cable to tracker, the
tactile marker on the charging cable head should point towards the BikeFinder
logo on the tracker as shown in the picture.
Tip: Charge the battery for a minimum of 2 hours regardless of battery
level indication.
Buy a subscription
Go to www.bikefinder.com to buy your subscription. BikeFinder has different
subscription offerings based on your country of residence. Some offerings
include insurance in addition to tracking.
lf purchasing an insurance subscription, please note that the insurance policy
depends on your country of residence.
Note: Make sure you buy a subscription with the same e-mail address as
you used when creating a login in the BikeFinder app. See step 4.
Download the app
You can download the BikeFinder app from App Store and Google Play.
After downloading the app, you must login with the same e-mail used when
purchasing the subscription. The app will guide you through the necessary
steps for activation of the tracker.
Activation of the tracker
To activate your BikeFinder tracker, you must do the following steps:
- Make sure Bluetooth is activated on your phone.
- Open the app.
- Click the + sign in the top right corner of the app.
- Select your tracker from the list of trackers nearby.
- If the tracker does not show on the list, try to shake the tracker.
- After the tracker is added, the app will automatically connect it to your purchased subscription. When your tracker is successfully connected to a subscription, the credit card sign will turn green in your BikeFinder App.
Tip: lf your BikeFinder tracker has an inactive subscription, check Buy a Subscription Step 3.
Mount the tracker
lnsert the tracker into the handlebar. If the handlebar diameter is bigger
than 20 mm, then see page 12 (section 20 mm+ handlebar adapter set) for
fitting expansion adapter and spacer.
Lock the tracker in place
Fasten the screws using the BikeFinder tool. Tighten the two screws evenly
until tracker is locked in place.
Note: The expansion mechanism can damage the interior of the handlebar if
tightened to hard.
Tip: Inspect the fastening periodically and keep the tightening torque
between 0.4-0.5 Nm to achieve optimal fastening result.
Plug in the front cover
Plug in the front cover during normal use. Your BikeFinder tracker is now
installed and ready to use. For more information on how to use the tracker go
to: www.bikefinder.com/getting-started.
Warning!
Do not cover this area with metal. Signal strength will be affected.
20 mm+ handlebar adapter set
Use the adapter set on the handlebars when inner diameter is larger than 20
mm.
- Remove the two expansion screws using the screwdriver tool provided in the box.
- Mount the two expansion adapters between the head of the tracker and the expansion mechanism as shown in the picture, reinstall the expansion screws. The screws should now pass through the designated holes in the expansion mechanism adapter before they are screwed into the expansion mechanism.
- Slide the silicone spacer onto the battery module section.
FCC WARNING STATEMENT
Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occure in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions to satisfy RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 4 W/kg averaged over one gram of tissue. The highest SAR value reported under the standard during product certification for use when properly worn on the body is CAT-M1: 0.108W/kg, NB-IoT: 0.299W/kg. For body operation, this device has been tested and meets FCC RF exposure guidelines when used with any accessory that contains no metal and the positions a minimum of 15 mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.
CE WARNING STATEMENT
The device is designed to meet the requirements for exposure to radio waves
established by the European Union. These requirements set a SAR limit of 4
W/kg averaging over ten gram of tissue when use in Limbs. This product was
tested and recorded the maximum reported SAR value was CAT-M1: 0.103W/kg, NB-
IoT: 0.342W/kg for Limbs.
Conducted power
- LTE CAT-M
- Band 1 max Conducted Power: 23.23dbm
- Band 3max Conducted Power: 23.32dbm
- Band 8 max Conducted Power: 23.44dbm
- Band 20 max Conducted Power: 23.33dbm
- Band 28 max Conducted Power: 23.44dbm
- LTE NB-IOT
- Band 1 max Conducted Power: 23.47dbm
- Band 3max Conducted Power: 23.49dbm
- Band 8 max Conducted Power: 23.45dbm
- Band 20 max Conducted Power: 23.45dbm
- Band 28 max Conducted Power: 23.54dbm
- WLAN2.4G max Conducted Power: 9.73dbm
- Bluetooth2.4G max Conducted Power: 4.28dbm,
Hardware version: 1.0 Software version: 1.2
Use Member States
The radio equipment can be used in at least one of the member state. Hereby,
BikeFinder AS declares that the radio equipment is in compliance with
Directive 2014/53/EU.
Please contact Support@bikefinder.com to
receive full text of the EU declaration of conformity.
- BikeFinder and the BikeFinder logo are trademarks of BikeFinder AS registered in Norway and other countries.
- Apple and the Apple logo are trademarks of Apple Inc. registered in the U.S. and other countries.
- App store is a service mark of Apple Inc. Registered in the U.S. and other countries.
- Google Play and the Google Play logo are trademarks of Google Inc.
- The Bluetooth word, mark and logos are registered trademarks owned by the Bluetooth SIG. Inc. and any use of such mark by BikeFinder AS is under license.
Box Content
- Tracker module
- Battery module
- Screwdriver tool
- Pincher tool
- Charging cable
- Adapter set
- User manual
Manufacturer
BikeFinder AS
Postbox 4004, 4092 Stavanger
Norway
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>