bikefinder BFG1S GPS Bike Tracker User Guide

BFG1S GPS Bike Tracker
User Guide

BFG1S GPS Bike Tracker

About
This manual describes the proper use of the Bike Finder tracker and all accessories. Make sure to read this before installation and activation of the tracker. Ensure that all warnings are read and understood before use.

Technical specifications

Product Name:BikeFider Tracker
Model: BFG1S
Network frequency: 850/900/1800/1900 Mhz, 2.4Ghz
Satellite system: GPS and GLONASS
Battery Rechargeable: 960 mAh Li-Ion battery, 0.5C
Power bank: Input 5VDC 2.1A, Output 5VDC 2.1A/1.0A
Hardware version:V1.3.2
Firmware version:V2.0/V2.3.0
Maximum Radiation Power: BT 4.27dBm
GPRS900 29. 18dBm
GPRS1800 28.43dBm

Compatibility

Handlebar inner diameter:

• 15.1-19.9mm (mount tracker without adapter)
• 20.0-27.0mm (mount tracker with adapter)

Requires BikeFinder subscription to function

Contact
Contact support through the app, or via support@bikefinder.com

Limitations and warranty

General Safety precautions

• Do not bend tracker more than 45 degrees
• Do not insert tools or pointy objects, other than those included, into USB socket or other openings in the tracker
• Do not open or tamper with any internal components
• Do not expose the tracker to water submersion or highpressure water jets
• Do not drop tracker onto hard surfaces or expose it to highenergy impacts
• Keep power bank and USB-cable away from moisture
• Keep tracker and accessories away from high pressure places, potentially explosive atmospheres and extreme temperature conditions (below -20 °C or higher than 45 °C)
• Keep away from medical electronic equipment
• When charging: use only included power bank

For full terms and conditions: www.bikefinder.com/terms
BikeFinder privacy policy: www.bikefinder.com/privacy
More information and video instructions: www.bikefinder.com/manual
Getting started information: https://bikefinder.freshdesk.com

Installation steps

1. Charge the tracker
   Remove USB cover and insert USB cable. A sound will come from the tracker, letting you know that it has started up.
   

2. Install the trackerMount the device and make sure that the direction arrows are pointing upwards to ensure correct installation.

3. Lock the tracker in place
   Fasten the screws using the tool. Tighten the two screws evenly until tracker is locked in place. Note: The expansion mechanism can damage the interior of the handlebar.
   Tip: Recheck the fastening periodically.

4. Plug in USB cover
   Plug in USB cover during normal use.
   Your tracker is now installed and ready to use. For troubleshooting and more information, go to www.bikefinder.com/manual
   Warning!
   Do not cover this area with metal . Singal strength will be affected.

5. Download the app
   The BikeFinder app lets you see the location of your bike at any time and choose beteen different settings.
   You can download the app from the App Store and Google Play.
   First you must register using your e-mail and pair the device using the app (see step 6). The app will guide you through the necessary steps.
   When your device is paired and activated you can choose from numerous settings in the app.

6. Activation of the tracker
   To activate your BikeFinder tracker you must follow the following procedure:
   

7. Make sure you buy a subscription on the same account (email) as you are using to log into your app on the phone or tablet

8. Open the app

9. Connect your tracker to your account via Bluetooth

10. The app will prompt you for activation of the tracker

FCC WARNING STATEMENT

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The equipment is designed to meet the requirements for exposure to radio waves established by the Federal Communications
Commission (USA). These requirements set a SAR limit of 4W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 3.442w/kg.
For body operation, this device has been tested and meets FCC RF exposure guidelines when used with any accessory that contains no metal and that positions a minimum of 15mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.

CE WARNING STATEMENT

The device is designed to meet the requirements for exposure to radio waves established by the European Union. These requirements set a SAR limit of 4.0 W/kg averaged over ten gram of tissue when use in Limbs. This product was tested and recorded the maximum reported SAR value was 2.434W/kg for Limbs.
Use Member States
The radio equipment can be used in at least one of the member state.
Hereby, Bikefinder AS declares that the radio equipment is in compliance with Directive 2014/53/EU.
Please contact Support@bikefinder.com to receive full text of the EU declaration of conformity.
20mm+ handlebar adapter set
Use the adapter set on handlebars with inner diameter larger than 20mm.Expansion mechanism adapter installation:

1. Remove the two expansion bolts using the screwdriver tool provided in the box
2. Mount the two expansion adapters and reinstall the expansion bolts

Silicone spacer installation:

1. Slide the silicone spacer into the device until the spacer is located as shown to the right

Power Bank

Product specifications:

Product Details: Function descriptions

1. The lights on/off indicate the USB output ports on/off states
2. The 4 lights are also the remaining battery level indicator, it represents battery level 25% – 50% – 75% – 99%
3. The lights will be flashing when the power bank is under charging
4. The power bank will be automatically turned on when the output port detects a rechargeable device, and it will be automatically turned off approximately 40 seconds after the rechargeable device is removed
5. The power bank can also be turned on/off manually. Press the switch button once to turn it on, and press it twice to turn it off
6. The power bank supports charging of on both of its output ports at the same time, however, the max charging current of each ports will be limited to 1A

Notes:

1. If charging other devices than the BikeFinder with the power bank, use the USB cable supplied with the device you are about to charge. This is to ensure compatibility

Tips:

1. There is a hole on the upper right corner of the power bank, you may attach a lanyard to the hole and hang it on your bike while charging

Apple and the Apple logo are trademarks of Apple Inc. registrered in the U.S and other countries.
App store is a service mark of Apple Inc. registered in the U.S and other countries.
Google Play and the Google play logo are trademarks of Google Inc.
The Bluetooth word, mark and logos are registrered trademarks owned by the Bluetooth SIG. Inc. and any use of such marks by Bikefinder AS is under license.

Box Content
Tracker
Tool
USB cable
Power bank
Adapter set
Manufacturer
BIKEFINDER AS
KVITSØYGATA 30, 4014 STAVANGER
NORWAY
www.bikefinder.com/manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>