DYNAUDIO Xeo 10 Active Wireless Hi-Fi Speakers Owner’s Manual

June 13, 2024
DYNAUDIO

Xeo 10 Active Wireless Hi-Fi Speakers

Product Information: Dynaudio Xeo 10/20/30

The Dynaudio Xeo 10/20/30 is a wireless hi-fi system that
combines the latest wireless technology with impressive sound
quality. It offers convenient and easy listening to music. The
system ensures perfect function and the best-possible sound
quality. The package includes Xeo 10/20/30 speakers and a remote
control.

Important Safety Instructions:

  • Read these instructions carefully.

  • Keep these instructions for future reference.

  • Heed all warnings provided.

  • Follow all instructions provided.

  • Do not use the system near water.

  • Clean the system only with a dry cloth.

  • Ensure proper ventilation by not blocking any ventilation
    openings.

  • Install the system according to the manufacturer’s
    instructions.

  • Avoid placing the system near heat sources.

  • Do not tamper with the safety features of the power plug.

Warning / Unpacking:

Warning: The speakers carry a risk of electric
shock when connected to the mains voltage. Always use the supplied
power cable for connection.

Remote Control Battery: Replace the battery
with the same or equivalent type to avoid the danger of explosion.
If swallowed, seek immediate medical attention.

Unpacking:

After unpacking, ensure that the system is complete and check
for any transport damage. Do not attempt to start up a damaged
device. If the contents are incomplete or damaged, contact your
Dynaudio Xeo distributor for assistance.

Removing the Protection Cap:

The tweeter is protected by a cap to prevent damage during
transport. After unpacking the speaker, remove the cap by pulling
it straight out.

Xeo 10/20/30
Owner’s manual

Search

Hello
Welcome to Dynaudio Xeo. We’ve taken care of the tech;
you take care of the music.

Search

This is Xeo

9 Introduction 9 Important safety instructions 10 Warning 10 Xeo 10/20/30 speakers 10 Remote control battery 11 Unpacking 11 Removing the protection cap 11 Packaging material 11 Disposal 12 Scope of delivery 13 Connections and control elements 13 Elements on the rear panel 14 Buttons on top of the cabinet (Xeo 10) 14 Remote control 15 Connecting and setting up 15 Positioning and connecting to mains voltage 15 Cloth cover 15 General settings 16 Connecting sources directly 16 Connecting a Bluetooth device 16 Connecting sources via Hub or Connect 17 Operation 17 Switching on

Search

17 Playback of connected sources 17 Playback of a Bluetooth device 18 Fixing the volume 18 Standby 19 Status LEDs on the front 21 Malfunctions 22 Accessories 22 Desk stand 22 Wall bracket 22 VESA 100 bracket (Xeo 10/20) 23 Setting up 25 Connection options 26 Division into audio zones 27 Components of the Xeo system 27 The Xeo system 28 Combination examples 30 Declaration of Conformity (EU only) 30 Reminding (USA and Canada only) 31 IC NOTICE 31 MPE Reminding 33 Technical data

Dynaudio Xeo 10/20/30

Thank you
6

for choosing Dynaudio Xeo. Xeo combines the latest wireless technology with impressive sound quality and makes listening to music truly convenient and easy. The next few pages contain important information on connecting the system and its operation to ensure perfect function and the best-possible sound quality. We hope you have a great time listening to your favourite music, Dynaudio
About this product The active Xeo 10/20/30 speakers are equipped with powerful integrated amplifiers and allow for the direct connection of various analog and digital audio sources. A Bluetooth interface enables the operation of Bluetooth devices and plays them back in optimal sound quality. Optional components like Xeo Hub or Dynaudio Connect enable setting up a wireless multiroom system without any restrictions to the highest sound quality. The speakers can be fully controlled with a remote control. The operational state of the system is indicated by two LEDs on the front.
About this manual This manual describes the operation of the Xeo 10/20/30 speakers. Information about the optional Xeo modules (Hub, Connect, Extender, Link) can be found in the Owner´s manual provided with these modules.

Search

Introduction 7

Dynaudio Xeo 10/20/30

Important safety instructions

Xeo The quintessential wireless hi-fi system
8

Important safety instructions

Search

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.
USA and Canada only: A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus. 15. To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle. 16. The mains plug of the power supply cord shall remain readily operable.
9

Dynaudio Xeo 10/20/30

Warning / Unpacking

Warning
10

Xeo 10/20/30 speakers
RISK OF ELECTRIC SHOCK! DO NOT OPEN! If the speakers are connected to the mains voltage, a dangerous electrical voltage is present inside the speakers. Use the supplied power cable to connect the speakers to the mains voltage. Make
sure that the power supply cable is not damaged; replace it with a new one if it has been damaged. To reduce the risk of electric shock, do not remove the back panel and never open the speaker housing. Do not expose the speakers to rain or moisture. No user serviceable parts inside. Refer servicing to qualified personnel. Do not operate defective speakers and disconnect defective speakers from the mains voltage. Please contact your Dynaudio Xeo distributor if you have any problems. Distributor addresses can be found on the Internet at dynaudio.com.
Remote control battery
DANGER OF EXPLOSION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
CHEMICAL BURN HAZARD If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. If you think batteries might have been swallowed or placed inside any part of the
body, seek immediate medical attention.

Unpacking

Search

After unpacking, make sure the system is complete and check the device and all accessories for transport damage. Transport damage may be expected if the packaging is already severely harmed. Do not attempt to start up a damaged device. If the contents are incomplete or damaged, please contact your Dynaudio Xeo distributor. Distributor addresses can be found on the Internet at dynaudio.com.
Removing the protection cap
The tweeter is protected by a cap to prevent damage during transport and unpacking. After you have unpacked the speaker, remove the cap by just pulling it straight out.
Packaging material
The packaging has been designed so that it may be reused as long as it has not been damaged during transport. Keep the packaging and use the original packaging for all further transport.
Disposal
Disposal of used electrical and electronic equipment (applicable in European countries with separate collection systems for this equipment) This symbol on the product or its packaging indicates that the product must not be treated as household waste. Instead, it must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials helps to conserve natural resources. For more detailed information on recycling this product, please contact your local authority, community waste disposal office, or the shop where you purchased the product.
11

Dynaudio Xeo 10/20/30

Scope of delivery / Connections and control elements

Scope of delivery
1
12

1 2 Xeo 10/20/30 speakers 2 2 Xeo 10/20/30 speaker cloth covers 3 1 Xeo 10/20/30 remote control 4 2 power cables (country-specific version, length: 2.5 m) 5 1 stereo cable (RCA ­ RCA, length: 1.5 m) (Xeo 10 only) 6 1 optical cable (Toslink ­ Toslink, length: 1.5 m) (Xeo 10 only) 7 1 stereo cable mini jack (3.5 mm ­ 3.5 mm, length: 1.5 m) (Xeo 10 only)
1 Xeo first time setup manual (quick guide for installation, not shown)

4

2

MUTE ON OFF

1 Line

2 Opt

VOLUME Line

3 Coax 4 USB

Opt

A

Aux

B

DIRECT

C HUB

3

5 6 7

Search

Connections and control elements

This section describes the connections and control elements. Please contact your Dynaudio Xeo distributor if you have any problems with connection and start-up. Distributor addresses can be found on the Internet at dynaudio.com.
Elements on the rear panel
The Xeo 10/20/30 set consists of a master and a slave unit. The master unit carries the audio input interfaces.

A: Speaker position

Speaker Position
Zone

Neutral Wall
Corner
I

Left Right

Red Green Blue

1

2

3

4

Aux In

R

L

Line In

Optical In Service

II (master unit only)

Mains socket

II B: I Speaker
ID/Zone
C: A B
D: C D E E: F
F:

Sound adjustment (depending on the position of the speakers) · Neutral = with free-standing placement · Wall = if placed near a wall · Corner = if placed in a corner Speaker placement · Left = left speaker for stereo mode · Right = right speaker for stereo mode
Selection of audio zones: Speakers assigned to different zones can be controlled separately via the remote control. The zones are identified as Red, Green, and Blue.
Aux In: To connect an analog audio source to the speaker via mini jack. Line In
To connect an analog audio source to the speaker via RCA.
Optical In (Toslink):To connect a digital audio source to the speaker.
USB In For firmware update only. Mains socket To connect the speaker to the mains voltage.

13

Dynaudio Xeo 10/20/30

Connections and control elements / Connecting and setting up

Buttons on top of the cabinet (Xeo 10)

Speaker on/off Press to switch on the speakers. The Xeo 10 will scan the inputs for a
signal. Press and hold to switch off the speakers. Input selection When switched on, press to jump to another input.

Volume control

Bluetooth pairing

Press or to raise or lower the Press and hold both and to

volume level. Press and hold for

start pairing (see page 16).

faster adjustment.

MUTE ON OFF

1 Line

2 Opt

VOLUME Line

3 Coax 4 USB

Opt

A

Aux

B

DIRECT

C HUB

Remote control
Commands will always apply to both of the speakers.

MUTE ON/OFF VOLUME

Muting the speakers Press to mute or unmute the
speakers.

Fixing the volume Press for at least 2 seconds to set
a high volume for the speakers (see page 18).

Speaker on/off

Reset

Press to switch on the speakers. Press for at least 5 seconds to

Press for standby mode. Press

reset the speakers to the factory

for at least 5 seconds to put the settings.

speakers in sleep mode.

Volume control Press or to raise or lower the volume level.

Connecting and setting up

Positioning and connecting to mains voltage
Position the speaker in the desired location. ­ Do not expose the speaker to direct sunlight, heat, or moisture. ­ Do not place the speaker near devices with strong electromagnetic radiation or devices that could be destroyed or damaged by magnetic fields.
Use the power cable to connect the speaker to the mains voltage.
Tip Xeo 10: · For easier access, the plate at the bottom of the cabinet can be removed. Use a coin
or screwdriver to loosen the screw and attach the plate after connecting the power cable.
Cloth cover
The cloth cover has been designed so it does not influence the sound dispersion of the speaker. It is attached to the housing with magnets and may be removed if needed.
General settings
In stereo mode: ­ Select Left operating mode for the left speaker. ­ Select Right operating mode for the right speaker.
Set the speaker position switch that best describes the speakers´ need for acoustic compensation. ­ Neutral = with free-standing placement ­ Wall = if placed near a wall ­ Corner = if placed in a corner
Select the Red, Green, or Blue zone. Select the same zone for the right and left speakers (for additional information about the audio zones, see page 26).

INPUT

Signal source Press a button to select the
respective signal source. selects a Bluetooth device or
Hub/Connect.

Bluetooth pairing Press for at least 5 seconds to
enter pairing mode.

Controls

= backward, = play or pause,

Press to control most Bluetooth 4.1

= forward

compliant devices:

14

15

Search

Dynaudio Xeo 10/20/30

Connecting sources directly
Connect your source cables to one or more of the audio inputs Aux , Line , Opt of the master speaker (see ,,Connection options” on page 13).
After it is turned on, the speaker automatically searches for an audio signal and then plays it back immediately. If several signal sources are active, one of the signal sources will be played back.
Tip (Xeo 10): · For easier access, the plate at the bottom of the cabinet can be removed. Use a coin
or screwdriver to loosen the screw and attach the plate after connecting the power cable.
Connecting a Bluetooth device
1. To begin Bluetooth pairing, press and hold both and buttons on either one of your speakers (Xeo 10). Alternatively, hold Bluetooth on remote for 5 seconds. ­ Once available for pairing, the status indicator will blink white and it will be available for pairing for one minute.
2. Go to settings on your device, find the Bluetooth sub-menu, and simply pair your device with your Xeo speaker by selecting Red, Green, or Blue. The speaker will store your pairing.
Connecting sources via Hub or Connect
Xeo Hub and Dynaudio Connect are optional components that allow you to connect analog and digital sources and are linked with your Xeo speaker via a wireless, lossless signal. For further information about the complete Xeo system, please see ,,The Xeo system” on page 27.

16

Search

Connecting and setting up / Operation

Operation

Switching on
To switch the speakers on from standby mode: Press on top of one of the speakers (Xeo 10) or point the remote control at a
speaker and press . ­ The speakers will automatically search for an active audio signal. If found, the
signal will be output (autoplay function). ­ If there is no input signal, the speakers will continue scanning the inputs for the
next 20 minutes and enter sleep mode.

If there is no input signal, the speakers will go into standby mode after a certain period.
Playback of connected sources
Once you have connected your Xeo speaker with a direct input, simply choose your desired source on the remote. ­ The speakers will automatically detect the signal and start playback. Master and slave speaker will connect wirelessly if set in the same zone. ­ If no signal is applied to either input, the speakers will continue scanning the inputs for the next 20 minutes and enter sleep mode.
Playback of a Bluetooth device
Once you have paired your device with your Xeo 10/20/30, you can connect by choosing the Xeo 10/20/30 from your list of Bluetooth devices. Select Bluetooth on the remote control and press play on your Bluetooth device.

Disconnect Press and hold
directly.

to disconnect a connected device or disconnect from the device

17

Dynaudio Xeo 10/20/30

Fixing the volume

You can set the speaker to a higher volume using the function to fix the volume. This setting also remains in effect in standby mode. If a signal source is connected to the Xeo 10/20/30 with its own volume control, you have the option to change the output volume across a broad range with the signal source.

To fix the volume: Point the remote control at a speaker and press
fixing, press one of the two volume buttons.

for at least 2 seconds. To undo

Standby
To switch speakers to sleep mode: Point the remote control at a speaker and press or press on top of one of the
speakers. ­ The speakers will enter sleep mode. ­ The speakers also enter sleep mode if there is no audio signal for 20 minutes. ­ In this mode, the wireless network is active and all connected units remain
synchronized. ­ Sleep mode power consumption is <2 W.

To switch speakers to low-power standby mode: Press and hold on the remote control for at least 5 seconds.
­ The speakers go to low-power standby mode. ­ In this mode, the wireless network is disabled and the speakers are not connected
to each other. ­ Low-power standby mode power consumption is <0.5 W.

To turn off auto standby: Press and hold Opt on the remote control for at least 5 seconds.

18

Search

Fixing the volume

Status LEDs on the front
The two LEDs in the upper left corner of the cabinet front indicate the operational state of the speakers and system with various colours and blinking functions.

On-state Illuminated in blue On-state Slow blinking in blue On-state Illuminated in purple On-state Slow blinking in purple Connection Slow blinking in red

The speaker is switched on, connected to a Hub or Connect, and an audio signal is played back. The speaker is switched on, connected to a Hub or Connect, but an audio signal cannot be found. The speaker is switched on, connected to a local input, and an audio signal is played back. The speaker is switched on, connected to a local input, but an audio signal cannot be found. There is no active transmitter2)/master or no connection possible.

Search Fast blinking in blue for 20 min Searching for an active input.

Synchronization/ Fast blinking in red for 10 s Connection Blue LED is turned off for 0.2 s Illuminated in red for 5 s Illuminated in white Slow blinking in white
Firmware loading White LED: slow to fast blinking during the load sequence, Red LED: illuminated
Volume Fast blinking in blue Mute Fading in and out
Off-state Illuminated dimly in red

System synchronization during no transmitter2)/master connection. New transmitter2) ID, transmitter2) input, or direct input is selected. Receiver mode is changing. Bluetooth connection is established. Speaker is in pairing mode. Firmware is being loaded.
Volume is being adjusted. Speaker is muted. Speaker is in standby mode.

  1. depending on the resolution of the audio source, 2) Hub, Connect, mobile device, etc.

LED blinking code

off

Illuminated in

white

Illuminated in a colour

Slow blinking (1 or 2 Hz)

Fast blinking (3 or 4 Hz)

19

Dynaudio Xeo 10/20/30 20

Malfunctions

Malfunctions

Interruptions, clicking noises, or other audible interference when playing music is usually not caused by radio transmission in the Xeo system. Often, other external causes influence the transmission quality.
Below are a few tips for improving transmission quality: 1. Position all radio transmitters and receivers away from each other. WLAN devices,
radio receivers, and radio systems may influence each other if they are too close together. Test out various locations for each device. 2. Switch off the automatic search function in WLAN devices. WLAN devices and other radio systems permanently scan for available frequencies, thus sending signals that could disrupt other radio systems. This automatic search function can usually be switched off. 3. Xeo technology radio signals can, of course, transmit through walls. However, walls may consist of very different materials, such as wood fibreboard, stone, or even steel. The walls may also contain complex cable installations for electrics, phones, TVs, and radios, as well as water pipes and air shafts. These can divert radio signals. This is why you should test different locations for the Xeo Hub, Extender, and Link and favour the most direct radio path between the Xeo components. 4. Some electrical devices, such as microwaves, generate strong electromagnetic fields that could disrupt radio systems. Do not operate such electrical devices near Xeo components.
You can ask your Dynaudio Xeo distributor for assistance at any time Or go to dynaudio.com/support to read the FAQ or to contact the Customer Support Team. Further information can also be found on the Xeo website at dynaudio.com/xeo

Search

21

Dynaudio Xeo 10/20/30

Accessories / Setting up

Accessories
22

Accessories (Xeo 10) A desk stand or wall brackets extend the range of applications of your Xeo 10 speakers. For further information, please see the website at dynaudio.com or contact your Dynaudio distributor. Distributor addresses can also be found at dynaudio.com
Desk stand
The Dynaudio desk stand for Xeo 10 is an elegantly designed stand for placing the speakers on a desk or shelf. A installation instruction is provided with the stand.
Wall bracket
The wall bracket allows you to mount the Xeo 10 speakers on the wall.

VESA 100 bracket (Xeo 10/20)
VESA is a standard for wall brackets developed by the Video Electronics Standards Association. The Xeo 10 and Xeo 20 speakers allow you to mount brackets according to the VESA 100 standard. This means that the screws on the back plate are spaced 100 mm apart.
To mount a VESA 100 bracket (Xeo 10): 1. Loosen the four screws (Torx type)
and unmount the back plate. 2. Keep the back plate for future use.
Follow the instructions provided with the bracket you want to mount.

Search

Setting up

Spikes with pointed ends Xeo 30 floor-standing speakers are delivered with spikes for permanent installation on the floor. The pointed ends of the spikes may result in injuries and damage delicate floors.

Pay attention that you do not injure yourself with the spikes.
We recommend inserting the spikes in aluminium feet if you have delicate floors, such as parquet or laminate.
Position the speaker in the desired location. ­ Do not expose the speakers to direct sunlight, heat, or moisture. ­ Do not place the speakers near devices with strong electromagnetic radiation or devices that could be destroyed or damaged by magnetic fields.

23

Dynaudio Xeo 10/20/30 24

Search

Connection options

Connection options

Connect your signal source to the appropriate input on the Xeo 10/20/30 speaker. Following table gives a selection of signal sources and options for connecting to the Xeo speaker.

Your signal source
Notebook, MacTM, PC
Smartphone, other portable devices Astell&Kern PonoPlayer Docking station, network client, Sonos, Bluesound, etc. Google Chromecast Audio
Apple AirPort Express Apple TV* Hard disk, network player, CD player Analog radio, digital radio
Analog record player TV
Stereo preamplifier Stereo power amplifier
Subwoofer AV receiver, AV processor

Signal source output
Optical Line out Headphones Headphones Headphones Optical Jack Line out Optical Line out Optical Optical Optical Line out Optical Line out Optical Line out Headphones Line out Optical Pre-out, main out Tape out Pre-out, main out* Second pre-out Analog output Optical Pre-out, main out

Xeo 10/20/30 Cable

input*

(source ­ Xeo 10/20/30)

Optical In Line in Aux in Aux in Aux in Optical In Aux in Line in Optical In Aux in Optical In Optical In Optical In Line in Optical In Line in Optical In Line in Aux in Line in Optical In Line in Line in Line in Line in Line in Optical In Line in

Toslink ­ Toslink RCA ­ RCA Jack 3.5 mm ­ 3.5 mm Jack 3.5 mm ­ 3.5 mm Jack 3.5 mm ­ 3.5 mm Toslink ­ Toslink Jack 3.5 mm ­ 3.5 mm RCA ­ RCA Toslink ­ Toslink Jack 3.5 mm ­ 3.5 mm Mini Toslink ­ Toslink Mini Toslink ­ Toslink Toslink ­ Toslink RCA ­ RCA Toslink ­ Toslink RCA ­ RCA Toslink ­ Toslink RCA ­ RCA Jack 3.5 mm ­ 3.5 mm RCA ­ RCA Toslink ­ Toslink RCA ­ RCA RCA ­ RCA RCA ­ RCA RCA ­ RCA RCA ­ RCA Toslink ­ Toslink RCA ­ RCA

Notes

  • If available
    ­ ­ ­ If available
    Select a variant. ­
    up to 3rd generation * If available
  • If available * On phono preamplifier Select a variant.
  • If available ­ * Disconnect bridge
    ­ ­

25

Dynaudio Xeo 10/20/30

Division into audio zones
The Xeo speakers (as well as Xeo Link) can be assigned to audio zones using the Zone selector switch. All components assigned to the same zone can be operated together via the remote control.

Red Green Blue
Red Green Blue
Red Green Blue

Zone

Zone

Zone

Green Blue

The picture shows a possible zone configuration.

Red

26

Search

Connection options

The Xeo system
Xeo consists of several high-quality components that are optimally matched. When combined, they can fulfil the most demanding requirements for a wireless multi-room and multi-source system.

Components of the Xeo system

Xeo speakers

MUTE ON OFF

1 Line

2 Opt

VOLUME Line

3 Coax 4 USB

Opt

A

Aux

B

DIRECT

C HUB

The active Xeo speakers Xeo 10/20/30 receive the wireless signals from the Hub or Connect and play them back in optimal sound quality. In addition, the Xeo 10/20/30 can be connected directly to various audio sources. All speakers have an integrated amplifier and can be controlled with a remote control. Display elements indicate the operating state of the system and controls on the cabinet let you switch it on/off or change the volume without using the remote control.

Xeo remote control

The Xeo remote control can be used to turn the speakers on and off, change the volume, and select a Hub or Connect and its connected signal sources.

Dynaudio Connect and Xeo Hub
Xeo Extender

The Dynaudio Connect and Xeo Hub are the control centres for the Xeo system. Both offer a new level of wireless connectivity and convenience. Signal sources such as tuners, receivers, CD players, TVs, streaming clients, network players, MP3 players, or computers are connected to them. Signals are sent wirelessly and lossless to the connected Xeo or Focus XD speakers (or Xeo Link) where they are then played back.
The Xeo Extender extends the reception range of the Xeo Hub. As a result, Xeo speakers or other Xeo components can be operated further away from the Xeo Hub or Dynaudio Connect.

Xeo Link

The Xeo Link receives wireless signals from a Xeo Hub or Dynaudio Connect and outputs analog and digital signals from its connections. As a result, you can also connect active subwoofers, active speakers, or other components to the Xeo system.

27

Dynaudio Xeo 10/20/30

Combination examples
Below you will find several examples of Xeo component combinations. The high level of flexibility in the Xeo system enables even more variants. Ask your Dynaudio distributor to find the perfect solution for your needs.
Direct wired: Analog/digital audio sources + Xeo 10/20/30
Direct wireless: Bluetooth device (mobile phone, etc.) + Xeo 10/20/30
With Hub or Connect: Analog/digital audio sources + Hub or Connect + Xeo speaker

28

Search

Connection options
For extended range: Analog/digital audio sources + Hub or Connect + Extender + Xeo speaker
For additional speakers: Analog/digital audio sources + Hub or Connect + Xeo speaker plus + Link + active component (e.g. active subwoofer, active speakers, or power amplifier and passive speakers)
Note: The Extender and Link may also be combined.
29

Dynaudio Xeo 10/20/30

Connection options

Declaration of Conformity (EU only) Dynaudio A/S hereby declares, that the product Dynaudio Xeo 10 is in conformity with the following directives: · 2001/95/EF (Product Safety) · 2006/95/EF (Low Voltage directive) · 2004/108/EF (EMC directive) · 1999/5/EC (R&TTE directive) · 2011/65/EU (ROHS directive) · 1275/2008 (ErP, Ecodesign directive) The Declaration of Conformity is available on the Internet at dynaudio.com/support/manuals

Reminding (USA and Canada only) A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à Ia section 15 des réglementations de Ia FCC. Le fonctionnement de l`appareil est sujet aux deux conditions suivantes:

(1) cet appareil ne doit pas provoquer d`interférences néfastes, et (2) cet appareil doit tolérer les interférences reçues, y compris celles qui risquent de provoquer un fonctionnement indésirable.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving
antenna. · Increase the separation between the
equipment and receiver. · Connect the equipment to an outlet
on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.

30

Search

IC NOTICE This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

MPE Reminding This equipment should be installed and operated with a minimum distance 20 cm between the radiator and your body. (i) The device for operation in the band 5150 ­ 5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) The maximum antenna gain permitted for devices in the bands 5250 ­ 5350 MHz and 5470 ­ 5725 MHz shall comply with the e.i.r.p. limit; and (ii1) The maximum antenna gain permitted for devices in the band 5725 ­ 5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to- point operation as appropriate.

Cet équipement doit être installe et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. (i) Tout appareil destiné à la bande 5150 ­ 5250 MHz devra être exclusivement utilisé en intérieur a fin de réduire les risques de perturbations électromagnétiques gênantes sur les systèmes de satellite mobile dans un même canal. (ii) Les radars à forte puissance sont désignés comme les utilisateurs principaux (cest-à-dire quils sont prioritaires) des bandes 5250 ­ 5350 MHz et (iii) 5650 ­ 5850 MHz. IIs peuvent provoquer des perturbations électromagnétiques sur les appareils de type LELAN (réseau de communication local sans licence) ou les endommager.

31

Dynaudio Xeo 10/20/30

Technical data

All Apple products are trademarks of Apple Inc. All Sony products are trademarks of Sony Electronics Inc. All Sonos products are trademarks of Sonos Inc. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. All Google products are trademarks of Google Inc. Other trademarks and trade names are those of their respective owners.
An update to this manual may be necessary due to product improvements and new functions. The latest version of this manual is available on the Internet at dynaudio.com/support/manuals
302

Technical data

Data Analog inputs Digital inputs Wireless Frequency response (± 3 dB) Box principle Crossover Crossover frequencies Woofer Midrange Tweeter Amplifier power AC power input Standby power consumption Maximum power consumption Weight Dimensions (WxHxD)
Dimensions with feet/grille (WxHxD)

Xeo 30 Mini-Jack, RCA stereo Toslink 24bit / 96kHz 36Hz – 21kHz Bass Reflex 2½-way DSP based 200/4300Hz 2x14cm MSP 28mm soft dome 3x65W 100V – 240V, 50/60Hz <0.5W 165W 13.4kg / 29.5lbs 180x825x246mm 7.1×32.5×9.7in 228x852x275mm 9.0×33.5×10.8in

Search

Xeo 20 Mini-Jack, RCA stereo Toslink 24bit / 96kHz 40Hz – 21kHz Bass Reflex 2-way DSP Based 4700Hz 14cm MSP 28mm soft dome 2x65W 100V – 240V, 50/60Hz <0.5W 100W 6.2kg / 13.7lbs 180x320x257mm 7.1×12.6×10.1in 180x320x265mm 7.1×12.6×10.4in

Xeo 10 Mini-Jack, RCA stereo Toslink 24bit / 96kHz 40Hz – 21kHz Bass Reflex 2-way DSP Based 5000Hz 14cm MSP 28mm soft dome 2x65W 100V – 240V, 50/60Hz <0.5W 100W 4kg / 8.8lb 173x255x154mm 6.8x10x6.1in 173x255x164mm 6.8x10x6.5in
33

Xeo 10/20/30 Designed and engineered by Dynaudio Labs in Denmark

Search

Dynaudio A/S 8660 Skanderborg
Denmark
dynaudio.com
Owner’s manual Xeo 10/20/30, EN – Item no. 45563101B.
All text and image copyrights reserved. Subject to change without notice.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals