BODYCRAFT F660 Linear Bearing Hip Sled User Manual

BODYCRAFT F660 Linear Bearing Hip Sled

Product Information

Product Name: F660 HIP SLED
Manufacturer: BodyCraft, a division of Recreation Supply Inc.
Address: 7699 Green Meadows Drive Lewis Center, OH 43035
Model Number: F660 Product
Website: https://manual-hub.com/

Product Usage Instructions

1. Before using the F660 HIP SLED or starting any exercise program, consult your physician, especially if you are over the age of 35 or have pre-existing health problems.
2. Assemble the product on a flat and level surface to ensure proper function.
3. Clean the pads and frame regularly using warm, soapy water. Do not use harsh or abrasive chemicals.
4. Before each use, inspect and tighten all parts. Replace any worn parts immediately to avoid serious injury.
5. Keep children away from the F660 HIP SLED at all times.
6. During operation, keep your hands away from cables and pulleys, except for the designated handles.
7. When adjusting the seat, ensure that the spring pin is fully engaged to prevent the seat from slipping and causing injury.
8. Exercise with care to avoid injury.
9. If you are unsure about the proper use of the F660 HIP SLED strength training system, contact your local dealer or BodyCraft’s customer service department at 800-990-5556.

Parts List

1. Main Frame

   • Quantity: 1

2. Front Stabilizer

   • Quantity: 1

3. . Rear Upright

   • Quantity: 1

4. Linear Bearing Assembly

   • Quantity: 1

5. Solid Guide Rod

   • Quantity: 2

6. Base Connector

   • Quantity: 1

7. Right Shoulder Assembly

   • Quantity: 1

8. Left Shoulder Assembly

   • Quantity: 1

9. Leg Press Plate

   • Quantity:1

10. Foot Platform

    • Quantity: 1

11. Hip Pad Plate

    • Quantity: 1

12. Weight Holder

    • Quantity: 1

13. . Calf Block

    • Quantity: 1

14. Weight Holder Support

    • Quantity: 1

15. Right Safety Stopper

    • Quantity: 1

16. Left Safety Stopper

    • Quantity: 1

17. Foot Platform Adjuster Sleeve

    • Quantity: 1

18. Foot Platform Adjuster Inside Tube

    • Quantity: 1

19. Metal Hinge

    • Quantity: 2

20. Foot Platform Axle

    • Quantity: 1

21. Foot Plate Axle

    • Quantity: 1

22. Plastic Cap

    • Quantity: 6

23. Hand Grip

    • Quantity: 2

24. 8mm Locking Pin

    • Quantity: 2

25. Spring Clip

    • Quantity: 2

26. Seat Pad

    • Quantity: 1

27. Back and Hip Pad

    • Quantity: 3

28. Back Supporter Pad

    • Quantity: 1

29. Back Pad

    • Quantity: 1

30. Right Shoulder Pad

    • Quantity: 1

31. Left Shoulder Pad

    • Quantity: 1

32. . 50 X 75mm End Cap

33. 45 X 45mm SQ CAP

    • Quantity:1

34. 75 X 50mm END PLUG

    • Quantity:2
      

35. 38mm ROUND PLUG

    • Quantity:4

36. 31mm ROUND PLUG

    • Quantity:2

37. 25mm ROUND PLUG

    • Quantity:2

38. 50 X 55mm PLASTIC SLEEVE

    • Quantity:2

39. 1/2″ X 18mm BUSHING

    • Quantity:4

40. LINEAR BEARING

    • Quantity:4

41. RUBBER BUMPER

    • Quantity:2

42. PLASTIC STUD

    • Quantity:3

43. SPRING KNOB

    • Quantity:3

44. POP PIN

    • Quantity:1

45. 1/2″ X 3-1/2″ HEX BOLT

    • Quantity:2

46. 1/2″ X 3-1/4″ HEX BOLT

    • Quantity:1

47. 1/2″ X 3″ HEX BOLT

    • Quantity:1

48. 5/16″ X 2-1/4″ HEX BOLT

    • Quantity:4

49. 3/8″ X 2-3/4″ HEX BOLT (ALL)

    • Quantity:2

50. 3/8″ X 1″ INNER HEX SCREW

    • Quantity:10

51. 3/8″ X 1/2″ INNER HEX SCREW

    • Quantity:3

52. ALLEN BOLT

    • Quantity:1

53. M8 X 30mm DOME BOLT

    • Quantity:2

54. 5/16″ X 1/4″ SET SCREW

    • Quantity:2

55. 1/2″ WASHER

    • Quantity:21

56. 3/8″ WASHER (LARGER)

    • Quantity:10

57. 3/8″ WASHER (SMALLER)

    • Quantity:3

58. SPRING CLIP

    • Quantity:4

59. 1/2″ NYLON NUT

    • Quantity:17

60. 3/8″ NYLON NUT

    • Quantity:4

61. 5/16″ SPRING WASHER

    • Quantity:4

62. 6mm HEX KEY

    • Quantity:1

63. 3mm HEX KEY

    • Quantity:1

64. FOAM TUBE

    • Quantity:2

65. 42mm ROUND PLUG

    • Quantity:2

66. NON SLIP

    • Quantity:2

67. 50 X 50mm SQ CAP

    • Quantity:1

68. 75mm ROUND END CAP

    • Quantity:2

QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your complete satisfaction through our authorized dealer service centers or our home office customer service department. Please call your local dealer for assistance or BodyCraft at 800-990-5556 (9:00 AM – 5:00 PM). Our trained technicians will provide immediate assistance to you, free of charge.
Bodycraft is a division of Recreation Supply Inc. 7699 Green Meadows Drive
Lewis Center, OH 43035

BEFORE YOU BEGIN
Congratulations and thank you for selecting the F660 HIP SLED strength training system. The F660 HIP SLED offers an impressive array of strength training exercises to develop every major muscle group of the body. Whether your goal is cardiovascular fitness, a shapely, toned body or dramatic muscle size and strength, the F660 HIP SLED will help you achieve the specific results you want. For your safety and benefit, read this manual and the accompanying literature before using the F660 HIP SLED. Keep this manual for future reference. If you have additional questions, please call your local dealer or our customer service department at 800-990-5556 Monday through Friday, 9 a.m. until 5 p.m. Eastern Time.

IMPORTANT SAFETY NOTES

There is a risk assumed by individuals who use this type of equipment. Before beginning this or any other exercise program consult your physician. This is especially important for individuals over the age of 35 or persons with pre- existing health problems. Recreation Supply, Inc. assumes no responsibility for personal injury or property damage sustained by or through use of this product.

1. This product must be assembled on a flat, level surface to assure its proper function.
2. Clean pads and frame on a regular basis. We recommend warm, soapy water. Do not use harsh or abrasive chemicals.
3. Inspect and tighten all parts before every use. Replace any worn parts immediately. Failure to do so may result in serious injury.
4. Keep children away from the F660 HIP SLED at all times.
5. Keep your hands away from cables and pulleys during operation. Keep your hands away from moving parts other than the designated handles.
6. When adjusting the seat, make sure the spring pin is fully engaged. If not, the seat may slip and cause serious injury.
7. Exercise with care to avoid injury.
8. If unsure about the proper use of the F660 HIP SLED strength training system call your local dealer or our customer service department at 800-990-5556.

OVERVIEW

Base Frame Assembly

To ease the assembly process, do NOT tighten bolts until instructed. Assembly requires two people.

1. Attach the Base Connector (6) to the Bolts welded on the Front Stabilizer (2) using two 1/2″ Washers (55) and two 1/2″ Nylon Nuts (59).
2. Attach the Base Connector (6) to the Bolts welded on the Rear Upright (3) using two 1/2″ Washers (55) and two 1/2″ Nylon Nuts (59). Slide the two 50 X 75 mm End Caps (32) onto the Front Stabilizer (2) and the Rear Upright (3).
3. Attach the pre-assembled Main Frame (1) to the vertical bolts welded on the Front Stabilizer (2) using two 1/2″ Washers (55) and two 1/2″ Nylon Nuts (59). Attach the Rear Upright (3) to the bolts welded to the top of the Main Frame (1) using two 1/2″ Washers (55) and 1/2″ Nylon Nuts (59). Slide the two 75 X 50 mm End Caps (34) onto the Main Frame (1).
4. Slide the 50X50 mm Sq Cap (67) onto the Linear Bearing Assembly (4).

Shoulder Pads, Safety Stoppers, and Weight Holder Assembly

1. Attach the Weight Holder Support (14) to the Weight Holder (12) using one 1/2″ X 3-1/4″ Hex Bolt ( 46), two 1/2″ Washers (55), and one 1/2″ Nylon Nut (59) on the top hole of the Weight Holder
   (12) and one 1/2″ X 3″ Hex Bolt (47) at the bottom threaded hole.

2. Attach the Weight Holder Assembly (12 & 14) to the bolts welded to the underside of the Linear Bearing Assembly (4) and tighten with four 1/2″ Washers (55) and four 1/2″ Nylon Nuts (59).

3. Insert the top end of the Right Safety Stopper (15) into the top bracket on the Main Frame (1) and then slide the bottom end into the low bracket on Main Frame (1). Check to make sure the Safety Stopper rotates and slides freely. Insert an 8mm Locking Pin (24) into the hole on the top of the Right Safety Stopper (15). Tap the Locking Pin with a hammer to makes sure it is permanently attached. Repeat the procedure for the Left Safety Stopper (16).

4. Attach two 38mm Round Plugs (35) to the top on both Shoulder Assemblies (7, 8). Attach one 31 mm Round Plug (36) to the handles at the top on both Shoulder Assemblies (7, 8).

5. Pull the Spring Knob (43) on the right side of the Linear Bearing Assembly (4) and insert the Right Shoulder Assembly (7). Attach the Right Shoulder Pad (30) to Right Shoulder Assembly (7) using two 5/16″ X 2-1/4″ Hex Bolts (48) and two 5/16″ Spring Washers (61).

Repeat the same procedure 24 for the Left Shoulder Assembly (8).

Leg Press Plate and Foot Platform Assembly

1. Attach the bottom side of the Foot Platform (10) to the Main Frame (1) by aligning the holes and then inserting the solid Foot Platform Axle (20). Attach a 3/8″ Nut (60) to each side of the Foot Platform Axle (20).
2. Find the Foot Platform Adjuster Sleeve (17). Pull the Spring Knob (43) and insert the Foot Platform Adjuster Inside Tube (18). Attach the Foot Platform Adjuster Sleeve (17) to the Front Stabilizer (2), using one 1/2″ X 3-1/2″ Bolt (45), two 1/2″ Washers (55) and one 1/2″ Nylon Nut (59).
3. Attach the Foot Platform Adjuster Inside Tube (18) to the Foot Platform (10) using one 1/2″ X 3- 1/2″ Bolt (45), two 1/2″ Washers (55), and one 1/2″ Nylon Nut (59).
4. Attach a Back Pad (27) to the Leg Press Plate (9) using two 3/8″ X 1″ Hex Screws (50). Attach the Leg Press Plate (9) to the Linear Bearing Assembly (4) by aligning the holes and then inserting the solid Foot Plate Axle (21). Secure with a 3/8″ Nut (60) on both sides. Pull the Pop Pin (44) on the Linear Bearing Assembly (4) to adjust the Leg Press Plate (9) to your desired angle.

Back Pad Assembly

1. Adjust the Leg Press Plate (9) to the flat position and then attach the Back Pad (29) to the Linear Bearing Assembly (4) using two 3/8″ X 2-3/4″ Hex Bolts (49) and two 3/8″ Washers (56).
2. Attach two Back Pads (27) to Hip Pad Plate (11) using four 3/8″ X 1″ Hex Screws (50) and two 3/8″ Washers (56).
3. Slide the two Metal Hinges (19) onto the small axles welded to the top of the Foot Platform (10) and then attach the Back Pad (28) to the Metal Hinges (19) using two 3/8″ X 1″ Hex Screws (50) and two 3/8″ Washers (56).
4. The Spring Clips (25) are used to hold the weight plates on the Weight Holder (12).

Calf Raise Assembly

1. Attach two Non Slips (66) to the Calf Block (13A). Attach one 50mm End Plug (33) and two 75mm Round End Caps (69) to the Calf Block (13A). To perform calf raises, insert the Calf Block into the central hole in the Foot Platform (10).
2. Attach Back Pad Assembly (27) to the Leg Press Plate (9).

Assembly is complete! Please take the following steps before using the gym:

1. Make certain all bolts are tightened securely.
2. For better performance, apply a household lubricant (such as silicone) to any adjustable areas and to the Linear Bearing Assembly(4).
3. Enjoy many years of a Fit Lifestyle.

Thank you for purchasing the F660 HIP SLED. If You have any questions, please call your local BodyCraft dealer or call our customer service department at 800-990-5556

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>