Hunter 13110 Vanning 1 Light Mini Pendant Instruction Manual
- June 13, 2024
- Hunter
Table of Contents
Hunter 13110 Vanning 1 Light Mini Pendant
Product Information:
The product is a lighting fixture that is designed to be installed on the ceiling. It comes with a mounting bracket assembly, a canopy, a glass dome, a socket cover, and necessary screws and nuts for installation. The fixture is compatible with a variety of light bulbs, and it has a maximum recommended wattage that should not be exceeded. The fixture is available in a Noble Bronze finish and comes with a clear glass dome.
Product Usage Instructions
- Carefully remove all contents from the packaging.
- Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket.
- Remove the new mounting bracket assembly from the bag.
- Remove cap nuts (H) from mounting screws (B).
- Place the mounting plate (A) over the junction box so that mounting screws (B) and nuts (C) extend out away from the ceiling.
- Adjust the position of mounting screws (B) so that they can be exposed 5-6 mm after passing through the canopy (F) to properly fit the cap nuts. Depending on the placement of your junction box, the position of mounting screws (B) may need to be adjusted to allow the canopy to be flush with the ceiling.
- Mounting screws (B) can be adjusted by loosening nuts (C) and loosening or tightening mounting screws (B).
- Once the ideal position of mounting screws (B) has been confirmed, tighten nuts (C) on mounting screws (B) on the front of the mounting plate to ensure that mounting screws (B) are secure.
- Pull the house wires through the center of mounting plate (A).
- Secure mounting plate (A) to the junction box by tightening the screws (D).
- Raise canopy (F) to mounting plate (A) and position mounting screws (B) so that they protrude through the openings of canopy (F).
- Secure canopy (F) in place with cap nuts (H).
- Place the glass (N) over the socket (M) and secure by screwing socket cover (O) onto socket (M).
- Install a light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage.
- Turn on the power and test the fixture to ensure it is functioning properly.
Cleaning Tips:
To clean the fixture, turn off the light and wipe it down with a clean lint- free cotton or microfiber cloth. Do not spray cleaner directly onto the fixture. Regular cleaning will reduce the need for deep cleaning.
Note: If you want to use a 12in. rod by itself, you must first remove the threaded post from the 6in. rod and install it on one of the ends of the 12in. rod. Twist or tape wire ends together to make it easier to pass them through the downrods. The threaded post may also be removed for easier wire access.
INCLUDE
1 Light Pendant
Fixture weight ±2 lbs: Peso ±2 lb:
Poids fixe ±2 lbs:
4.62 lbs (2.10 kg)
Here are the tools you’ll need to complete your installation:
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning installation of the
lighting fixture.
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. Remove cap nuts (H) from mounting screws (B). Place the mounting plate (A) over the junction box so that mounting screws (B) and nuts (C) extend out away from the ceiling. Adjust the position of mounting screws (B) so that mounting screws (B) can be exposed 5-6 mm after passing through the canopy (F) to properly fit the cap nuts. Depending on the placement of your junction box the position of mounting screws (B) may need to be adjusted to allow the canopy to be flush with the ceiling. Mounting screws (B) can be adjusted by loosening nuts (C) and loosening or tightening mounting screws (B). Once the ideal position of mounting screws (B) has been confirmed, tighten nuts (C) on mounting screws (B) on the front of the mounting plate to ensure that mounting screws (B) are secure. Pull the house wires through the center of mounting plate (A). Secure mounting plate (A) to the junction box by tightening the screws (D).
ASSEMBLING THE FIXTURE
There are 4 12-inch rods (K), and 1 6-inch rod (I) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. All threads should be engaged but do not overtighten (some manual straightening of the down rods may be required). Screw rod onto threaded post (L) of the fixture. Pull the fixture wires through the top of the canopy. Screw the top rod to hang straight (G) of canopy (F).
CONNECTING THE WIRES
Have a helper support the fixture’s weight while completing the wiring. Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (live); white to white (neutral); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (E) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Raise canopy (F) to mounting plate (A) and position mounting screws (B) so
that they protrude through the openings of canopy (F). Secure canopy (F) in
place with cap nuts (H). Place the glass (N) over the socket (M) and secure by
screwing socket cover (O) onto socket (M). Install light bulb (not included)
in accordance with the fixture’s specifications. Do not exceed the recommended
wattage. Turn on the power and test the fixture. Your installation is now
completed.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep
cleaning. For regular cleaning, turn off the light and wipe down the fixture
with a clean lint-free cotton or microfiber cloth. Never spray cleaner
directly onto the fixture.
NOTICE
In order to use a 12in. rod by itself you must first remove the threaded
post from the 6in. rod and install it on one of the ends of the 12in. rod.
Hunter Pro Tip:
Twist or tape wire ends together to make it easier to pass them through the
downrods. Threaded post may also be removed for easier wire access.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>