AMP RESEARCH 74830-01A Black Bed X Tender HD Truck Bed Extender Installation Guide
- June 13, 2024
- AMP RESEARCH
Table of Contents
ASSEMBLY & INSTALLATION GUIDE
Bed X Tender HD
MADE IN USA
74830-01A Black Bed X Tender HD Truck Bed Extender
APPLICATION| YEAR| PART #|
---|---|---|---
RAM DT| 2019 – 2023| 74830-00A (Silver)| 74830-01A(Black)
(Not compatible with Ram Box or Multifunction Tailgate applications)
BEDXTENDER HD™ shown assembled and installed on truck.
Remove contents from box and check for damage.
Verify all parts against parts list.
Read and understand instructions completely before attempting assembly and
installation.
INSTALLATION TIME
1 Hour
SKILL LEVEL
1= Easy
TOOLS REQUIRED
Phillips screw driver
Torx T-25 driver
Power drill
5/32” drill bit
Center punch
Supplied templates
Soapy Water
WARRANTY
3-Year Limited Warranty
PARTS LIST AND HARDWARE IDENTIFICATION
UNIVERSAL MOUNTING BRACKET INSTALLATION
BED X-TENDER ASSEMBLY
-
Using template measure 7” from each end of the three long tubes and mark with tape. Tape is to be used as a reference point. (See step 6) Note: Template located on inside of box
-
Slide the center tube (With Amp logo) into the center tube of the 3-tube assembly. Be sure to slide on Strap Buckle Assembly to center tube of Pivot Upright Assembly Note: Tubes do not need to be pushed in to taped edge.
-
Insert the top long tube into the top tube of the 3-tube assembly. Note: If tube joints are tight Soapy Water can be used.
-
Insert the bottom long tube into the bottom tube of the 3-tube assembly.
-
Repeat for the other side. Note: Install Strap Buckle Assembly to center tube of Pivot Upright Assembly.
-
Adjust the width of the BEDXTENDER to fit the preinstalled mounting brackets.
To keep tube overlap constant, adjust each tube so that the gap between the edge and the tape is the same. -
Attach plastic upright around the tube juncture, placing rubber bumpers into the two ends of the upright.
NOTE: The inside of the upright is stepped to fit correctly around the small and large diameter tubes. -
Tighten PT-Screws using a T-25 torx driver, starting in the middle of each upright, then the outer screws and lastly the remaining two to evenly tighten. NOTE: Do not over tighten as this may strip out. Fastener will reach a noticeable stopping point.
-
Adjust Strap Buckles to lock into the tailgate when BEDXTENDER is deployed.
Your assembly is now complete.
When the BEDXTENDER is at the furthest rear position, push down on the buckle to insert into tailgate latch. Tighten straps. To release, pull tailgate handle.
NOTE: Ensure that buckles are properly inserted into latches by pulling on the straps after both buckles have been inserted.
-
Pull tailgate release handle to release buckles from the tailgate.
Before flipping the Bed Extender into the cargo divider position, secure the buckles/straps on the top clips while the Bed Extender is outward position, this is to secure them from swinging.
-
The straps will be secured on the bottom clips when Bed Extender is flipped in, this will leave the top clips free to use to hold grocery bags if needed. Closing tailgate to keep cargo secured in bed.
AMERICAN DESIGNED, ENGINEERED AND MANUFACTURED.
Thank you for your recent AMP Research Purchase.
REGISTER YOUR PRODUCT TODAY FOR FASTER SERVICE & PRODUCT UPDATES
Please visit:
www.amp-research.com/productregistration
or scan the QR Code
http://www.amp-research.com/productregistration
Product Registration Benefits:
- Ensure we have your purchase receipt and product info in our system which is required for warranty
- Faster and easier access to customer service and tech support in the unlikely event you need warranty or product support
- Registration helps us keep you up to date on product information and offers
To view other Amp Research products that may be offered for your vehicle. Please visit: www.amp-research.com
Congratulations on your purchase of the AMP Research BEDXTENDER HD.
Here’s what you need know…
BEDXTENDER HD™ OPERATION
With the tailgate open, place BEDXTENDER pivot pins into the left and right mounting brackets. Rotate to 45 until it drops into place, then lower onto the open tailgate.
Flip BEDXTENDER out to contain cargo in the truck bed when the tailgate is
open.
CAUTION! 200lb maximum load on open tailgate. Always distribute cargo evenly
and properly secure inside bed. Do not secure cargo to the BEDXTENDER or the
tailgate.
Before driving, secure BEDXTENDER by locking the provided strap buckles into the truck’s tailgate latches. To release, pull tailgate handle. NOTE: Ensure that both buckles are properly locked into the latches by pulling up on each strap.
Flip BEDXTENDER forward and close the tailgate to keep smaller cargo safe and organized.
AMP RESEARCH LIMITED WARRANTY
AMP RESEARCH warrants this product to be free from defects in material and
workmanship for THREE (3) YEARS FROM DATE OF PURCHASE, provided there has been
normal use and proper maintenance. This warranty applies to the original
purchaser only. All remedies under this warranty are limited to the repair
replacement of the product itself, or the repair or replacement of any
component part thereof, found by the factory to be defective within the time
period specified. The decision to repair or replace is wholly within the
discretion of the manufacturer.
This warranty specifically excludes labor. If you have a warranty claim, first
you must call our factory at the number below for instructions. You must
retain proof of purchase and submit a copy with any items returned for
warranty work. Upon completion of warranty work, if any, we will return the
repaired or replaced item or items to you freight prepaid. Damage to our
products caused by accidents, fire, vandalism, negligence, misinstallation,
misuse, Acts of God, or by defective parts not manufactured by us, is not
covered under this warranty.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE
AS THE EXPRESS WRITTEN WARRANTY. OUR OMPANY SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGE.
Some states do not allow limitations on how long an implied warranty lasts, or
the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that vary from state
to state.
FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH CUSTOMER
SERVICE 1-888-983-2204
WARNING
Be sure to read and precisely follow the provided instructions when installing
this product. Failure to do so could place the vehicle occupants in a
potentially dangerous situation. After installing or reinstalling, re-check to
insure that the product is properly installed.
The material that your product is made from can be recycled.
Please also consider recycling the packaging that your product came in.
AMP RESEARCH TECH SUPPORT
1-888-983-2204 Monday – Friday, 7:00 AM
– 5:00 PM PST
Designed and manufactured by AMP Research. Patent 5,700,047; 6,113,173;
6,402,215; 6,806,392; 7,063,366; 7,240,940; 7,393,035;7,547,054; D417,859;
D418,106;
D544,826 Other US and Worldwide patents pending. Made in USA. Three-year
limited warranty. “BED X-TENDER” is a trademark of AMP Research.
© 2010 AMP RESEARCH 15651 Mosher Ave., Tustin, CA 92780
www.amp-research.com
rev 03.27.23
Documents / Resources
| AMP
RESEARCH 74830-01A Black Bed X Tender HD Truck Bed
Extender
[pdf] Installation Guide
74830-01A Black Bed X Tender HD Truck Bed Extender, 74830-01A, Black Bed X
Tender HD Truck Bed Extender, Tender HD Truck Bed Extender, Truck Bed
Extender, Bed Extender, Extender
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>